Dave, Another big batch of wireless fixes for 2.6.27. The ath5k series is more than fixes, but I included it because it enables new ath5k hardware. (The ath5k.h changes in particular are documentation cleanups for registers based on info gleaned from the newly posted ath9k driver.) The others patches are fixes, some more obvious than others. :-) Let me know if there are any problems! Thanks, John --- Individual patches are available here: http://www.kernel.org/pub/linux/kernel/people/linville/wireless-2.6/ --- The following changes since commit 00b1304c4ca81dd893973cc620b87a5c3ff3f660: Adam Langley (1): tcp: MD5: Fix IPv6 signatures are available in the git repository at: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git master Andrea Merello (1): Rtl8187 PATCH add usb ID for asus wireless link Dan Williams (1): libertas: only enable rtap with mesh firmware Dmitry Baryshkov (2): RFKILL: allow one to specify led trigger name RFKILL: set the status of the leds on activation. Helmut Schaa (1): ath5k: remove obsolete declaration of struct ieee80211_hw_mode Henrique de Moraes Holschuh (1): rfkill: query EV_SW states when rfkill-input (re)?connects to a input device Ivo van Doorn (5): rt2x00: Fix access permissions on debugfs files rt2x00: Fix partial antenna configuration rt2x00: rt61pci needs another millisecond after firmware upload rt2x00: Fix VGC lower bound initialization rt2x00: Sequence counter should be protected in irqsave Jiri Slaby (1): Ath5k: mask out unneeded interrupts Larry Finger (1): rtl8187: Fix lockups due to concurrent access to config routine Maxim Levitsky (1): iwl3945: Fix statistics in monitor mode Nick Kossifidis (9): ath5k: Update register list ath5k: Restore saved initval after POST ath5k: Misc hw_attach fixes ath5k: Misc hw_reset updates ath5k: Do ADC test during reset ath5k: Reorder calibration calls during reset and update hw_set_power ath5k: Add RF2425 initial rfgain values ath5k: Update channel functions ath5k: Update phy calibration functions Peter Chubb (1): rt2500pci: restoring missing line Takashi Iwai (2): ipw2200 - Fix bad ipw_write8() macro prism54 - Use offsetof() Tomas Winkler (2): mac80211: fix fragmentation kludge iwlwifi: don't stop queue in the middle of fragmented packet drivers/net/wireless/Kconfig | 1 + drivers/net/wireless/ath5k/ath5k.h | 8 +- drivers/net/wireless/ath5k/base.c | 1 + drivers/net/wireless/ath5k/debug.c | 2 +- drivers/net/wireless/ath5k/debug.h | 1 - drivers/net/wireless/ath5k/hw.c | 239 +++++--- drivers/net/wireless/ath5k/initvals.c | 4 +- drivers/net/wireless/ath5k/phy.c | 185 +++++- drivers/net/wireless/ath5k/reg.h | 934 +++++++++++++++++++++------- drivers/net/wireless/ipw2200.c | 5 +- drivers/net/wireless/iwlwifi/iwl-3945.c | 10 +- drivers/net/wireless/iwlwifi/iwl-tx.c | 8 +- drivers/net/wireless/libertas/main.c | 15 +- drivers/net/wireless/prism54/isl_ioctl.c | 2 +- drivers/net/wireless/rt2x00/rt2500pci.c | 1 + drivers/net/wireless/rt2x00/rt2500usb.c | 6 +- drivers/net/wireless/rt2x00/rt2x00.h | 6 + drivers/net/wireless/rt2x00/rt2x00config.c | 4 + drivers/net/wireless/rt2x00/rt2x00debug.c | 17 +- drivers/net/wireless/rt2x00/rt2x00mac.c | 1 + drivers/net/wireless/rt2x00/rt2x00queue.c | 5 +- drivers/net/wireless/rt2x00/rt61pci.c | 5 + drivers/net/wireless/rtl8187.h | 4 + drivers/net/wireless/rtl8187_dev.c | 17 +- net/mac80211/ieee80211_i.h | 1 + net/mac80211/tx.c | 17 +- net/mac80211/util.c | 1 + net/rfkill/rfkill-input.c | 54 ++- net/rfkill/rfkill.c | 15 +- 29 files changed, 1161 insertions(+), 408 deletions(-) diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig index 91fc2c7..4c7ff61 100644 --- a/drivers/net/wireless/Kconfig +++ b/drivers/net/wireless/Kconfig @@ -649,6 +649,7 @@ config RTL8187 Trendnet TEW-424UB ASUS P5B Deluxe Toshiba Satellite Pro series of laptops + Asus Wireless Link Thanks to Realtek for their support! diff --git a/drivers/net/wireless/ath5k/ath5k.h b/drivers/net/wireless/ath5k/ath5k.h index ba35c30..9102eea 100644 --- a/drivers/net/wireless/ath5k/ath5k.h +++ b/drivers/net/wireless/ath5k/ath5k.h @@ -186,11 +186,13 @@ struct ath5k_srev_name { #define AR5K_SREV_RAD_2111 0x20 #define AR5K_SREV_RAD_5112 0x30 #define AR5K_SREV_RAD_5112A 0x35 +#define AR5K_SREV_RAD_5112B 0x36 #define AR5K_SREV_RAD_2112 0x40 #define AR5K_SREV_RAD_2112A 0x45 -#define AR5K_SREV_RAD_SC0 0x56 /* Found on 2413/2414 */ -#define AR5K_SREV_RAD_SC1 0x63 /* Found on 5413/5414 */ -#define AR5K_SREV_RAD_SC2 0xa2 /* Found on 2424-5/5424 */ +#define AR5K_SREV_RAD_2112B 0x46 +#define AR5K_SREV_RAD_SC0 0x50 /* Found on 2413/2414 */ +#define AR5K_SREV_RAD_SC1 0x60 /* Found on 5413/5414 */ +#define AR5K_SREV_RAD_SC2 0xa0 /* Found on 2424-5/5424 */ #define AR5K_SREV_RAD_5133 0xc0 /* MIMO found on 5418 */ /* IEEE defs */ diff --git a/drivers/net/wireless/ath5k/base.c b/drivers/net/wireless/ath5k/base.c index ff3fad7..ebf19bc 100644 --- a/drivers/net/wireless/ath5k/base.c +++ b/drivers/net/wireless/ath5k/base.c @@ -2170,6 +2170,7 @@ ath5k_beacon_config(struct ath5k_softc *sc) ath5k_hw_set_intr(ah, 0); sc->bmisscount = 0; + sc->imask &= ~(AR5K_INT_BMISS | AR5K_INT_SWBA); if (sc->opmode == IEEE80211_IF_TYPE_STA) { sc->imask |= AR5K_INT_BMISS; diff --git a/drivers/net/wireless/ath5k/debug.c b/drivers/net/wireless/ath5k/debug.c index 41d5fa3..6fa6c8e 100644 --- a/drivers/net/wireless/ath5k/debug.c +++ b/drivers/net/wireless/ath5k/debug.c @@ -129,7 +129,7 @@ static struct reg regs[] = { REG_STRUCT_INIT(AR5K_CPC1), REG_STRUCT_INIT(AR5K_CPC2), REG_STRUCT_INIT(AR5K_CPC3), - REG_STRUCT_INIT(AR5K_CPCORN), + REG_STRUCT_INIT(AR5K_CPCOVF), REG_STRUCT_INIT(AR5K_RESET_CTL), REG_STRUCT_INIT(AR5K_SLEEP_CTL), REG_STRUCT_INIT(AR5K_INTPEND), diff --git a/drivers/net/wireless/ath5k/debug.h b/drivers/net/wireless/ath5k/debug.h index 2cf8d18..ffc5293 100644 --- a/drivers/net/wireless/ath5k/debug.h +++ b/drivers/net/wireless/ath5k/debug.h @@ -63,7 +63,6 @@ struct ath5k_softc; struct ath5k_hw; -struct ieee80211_hw_mode; struct sk_buff; struct ath5k_buf; diff --git a/drivers/net/wireless/ath5k/hw.c b/drivers/net/wireless/ath5k/hw.c index 7ca87a5..ad1a5b4 100644 --- a/drivers/net/wireless/ath5k/hw.c +++ b/drivers/net/wireless/ath5k/hw.c @@ -139,6 +139,8 @@ static int ath5k_hw_post(struct ath5k_hw *ah) for (c = 0; c < 2; c++) { cur_reg = regs[c]; + + /* Save previous value */ init_val = ath5k_hw_reg_read(ah, cur_reg); for (i = 0; i < 256; i++) { @@ -170,6 +172,10 @@ static int ath5k_hw_post(struct ath5k_hw *ah) var_pattern = 0x003b080f; ath5k_hw_reg_write(ah, var_pattern, cur_reg); } + + /* Restore previous value */ + ath5k_hw_reg_write(ah, init_val, cur_reg); + } return 0; @@ -287,67 +293,42 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version) /* Identify the radio chip*/ if (ah->ah_version == AR5K_AR5210) { ah->ah_radio = AR5K_RF5110; + /* + * Register returns 0x0/0x04 for radio revision + * so ath5k_hw_radio_revision doesn't parse the value + * correctly. For now we are based on mac's srev to + * identify RF2425 radio. + */ + } else if (srev == AR5K_SREV_VER_AR2425) { + ah->ah_radio = AR5K_RF2425; + ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2425; } else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112) { ah->ah_radio = AR5K_RF5111; ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5111; } else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC0) { - ah->ah_radio = AR5K_RF5112; - - if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) { - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112; - } else { - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A; - } - + ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112; } else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC1) { ah->ah_radio = AR5K_RF2413; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A; + ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413; } else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC2) { ah->ah_radio = AR5K_RF5413; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A; + ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413; } else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5133) { - /* AR5424 */ if (srev >= AR5K_SREV_VER_AR5424) { ah->ah_radio = AR5K_RF5413; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5424; + ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413; /* AR2424 */ } else { ah->ah_radio = AR5K_RF2413; /* For testing */ - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A; + ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413; } - - /* - * Register returns 0x4 for radio revision - * so ath5k_hw_radio_revision doesn't parse the value - * correctly. For now we are based on mac's srev to - * identify RF2425 radio. - */ - } else if (srev == AR5K_SREV_VER_AR2425) { - ah->ah_radio = AR5K_RF2425; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112; } - ah->ah_phy = AR5K_PHY(0); /* - * Identify AR5212-based PCI-E cards - * And write some initial settings. - * - * (doing a "strings" on ndis driver - * -ar5211.sys- reveals the following - * pci-e related functions: - * - * pcieClockReq - * pcieRxErrNotify - * pcieL1SKPEnable - * pcieAspm - * pcieDisableAspmOnRfWake - * pciePowerSaveEnable - * - * I guess these point to ClockReq but - * i'm not sure.) + * Write PCI-E power save settings */ if ((ah->ah_version == AR5K_AR5212) && (pdev->is_pcie)) { ath5k_hw_reg_write(ah, 0x9248fc00, 0x4080); @@ -369,10 +350,15 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version) if (ret) goto err_free; + /* Write AR5K_PCICFG_UNK on 2112B and later chips */ + if (ah->ah_radio_5ghz_revision > AR5K_SREV_RAD_2112B || + srev > AR5K_SREV_VER_AR2413) { + ath5k_hw_reg_write(ah, AR5K_PCICFG_UNK, AR5K_PCICFG); + } + /* * Get card capabilities, values, ... */ - ret = ath5k_eeprom_init(ah); if (ret) { ATH5K_ERR(sc, "unable to init EEPROM\n"); @@ -843,27 +829,41 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, * Write some more initial register settings */ if (ah->ah_version == AR5K_AR5212) { - ath5k_hw_reg_write(ah, 0x0002a002, AR5K_PHY(11)); + ath5k_hw_reg_write(ah, 0x0002a002, 0x982c); if (channel->hw_value == CHANNEL_G) if (ah->ah_mac_srev < AR5K_SREV_VER_AR2413) ath5k_hw_reg_write(ah, 0x00f80d80, - AR5K_PHY(83)); + 0x994c); else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2424) ath5k_hw_reg_write(ah, 0x00380140, - AR5K_PHY(83)); + 0x994c); else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2425) ath5k_hw_reg_write(ah, 0x00fc0ec0, - AR5K_PHY(83)); + 0x994c); else /* 2425 */ ath5k_hw_reg_write(ah, 0x00fc0fc0, - AR5K_PHY(83)); + 0x994c); else - ath5k_hw_reg_write(ah, 0x00000000, - AR5K_PHY(83)); - - ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); - ath5k_hw_reg_write(ah, 0x0000000f, 0x8060); + ath5k_hw_reg_write(ah, 0x00000000, 0x994c); + + /* Some bits are disabled here, we know nothing about + * register 0xa228 yet, most of the times this ends up + * with a value 0x9b5 -haven't seen any dump with + * a different value- */ + /* Got this from decompiling binary HAL */ + data = ath5k_hw_reg_read(ah, 0xa228); + data &= 0xfffffdff; + ath5k_hw_reg_write(ah, data, 0xa228); + + data = ath5k_hw_reg_read(ah, 0xa228); + data &= 0xfffe03ff; + ath5k_hw_reg_write(ah, data, 0xa228); + data = 0; + + /* Just write 0x9b5 ? */ + /* ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); */ + ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK); ath5k_hw_reg_write(ah, 0x00000000, 0xa254); ath5k_hw_reg_write(ah, 0x0000000e, AR5K_PHY_SCAL); } @@ -879,6 +879,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, else data = 0xffb80d20; ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL); + data = 0; } /* @@ -898,7 +899,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, /* * Write RF registers - * TODO:Does this work on 5211 (5111) ? */ ret = ath5k_hw_rfregs(ah, channel, mode); if (ret) @@ -935,7 +935,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, return ret; /* Set antenna mode */ - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x44), + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_ANT_CTL, ah->ah_antenna[ee_mode][0], 0xfffffc06); /* @@ -965,15 +965,15 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, ath5k_hw_reg_write(ah, AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]), - AR5K_PHY(0x5a)); + AR5K_PHY_NFTHRES); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x11), + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_SETTLING, (ee->ee_switch_settling[ee_mode] << 7) & 0x3f80, 0xffffc07f); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x12), + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_GAIN, (ee->ee_ant_tx_rx[ee_mode] << 12) & 0x3f000, 0xfffc0fff); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x14), + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_DESIRED_SIZE, (ee->ee_adc_desired_size[ee_mode] & 0x00ff) | ((ee->ee_pga_desired_size[ee_mode] << 8) & 0xff00), 0xffff0000); @@ -982,13 +982,13 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, (ee->ee_tx_end2xpa_disable[ee_mode] << 24) | (ee->ee_tx_end2xpa_disable[ee_mode] << 16) | (ee->ee_tx_frm2xpa_enable[ee_mode] << 8) | - (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY(0x0d)); + (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x0a), + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_RF_CTL3, ee->ee_tx_end2xlna_enable[ee_mode] << 8, 0xffff00ff); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x19), + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_NF, (ee->ee_thr_62[ee_mode] << 12) & 0x7f000, 0xfff80fff); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x49), 4, 0xffffff01); + AR5K_REG_MASKED_BITS(ah, AR5K_PHY_OFDM_SELFCORR, 4, 0xffffff01); AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE | @@ -1063,7 +1063,8 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); /* - * 5111/5112 Specific + * On 5211+ read activation -> rx delay + * and use it. */ if (ah->ah_version != AR5K_AR5210) { data = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) & @@ -1071,40 +1072,77 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, data = (channel->hw_value & CHANNEL_CCK) ? ((data << 2) / 22) : (data / 10); - udelay(100 + data); + udelay(100 + (2 * data)); + data = 0; } else { mdelay(1); } /* - * Enable calibration and wait until completion + * Perform ADC test (?) + */ + data = ath5k_hw_reg_read(ah, AR5K_PHY_TST1); + ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1); + for (i = 0; i <= 20; i++) { + if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10)) + break; + udelay(200); + } + ath5k_hw_reg_write(ah, data, AR5K_PHY_TST1); + data = 0; + + /* + * Start automatic gain calibration + * + * During AGC calibration RX path is re-routed to + * a signal detector so we don't receive anything. + * + * This method is used to calibrate some static offsets + * used together with on-the fly I/Q calibration (the + * one performed via ath5k_hw_phy_calibrate), that doesn't + * interrupt rx path. + * + * If we are in a noisy environment AGC calibration may time + * out. */ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL); + /* At the same time start I/Q calibration for QAM constellation + * -no need for CCK- */ + ah->ah_calibration = false; + if (!(mode == AR5K_MODE_11B)) { + ah->ah_calibration = true; + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, + AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, + AR5K_PHY_IQ_RUN); + } + + /* Wait for gain calibration to finish (we check for I/Q calibration + * during ath5k_phy_calibrate) */ if (ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL, 0, false)) { - ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n", + ATH5K_ERR(ah->ah_sc, "gain calibration timeout (%uMHz)\n", channel->center_freq); return -EAGAIN; } + /* + * Start noise floor calibration + * + * If we run NF calibration before AGC, it always times out. + * Binary HAL starts NF and AGC calibration at the same time + * and only waits for AGC to finish. I believe that's wrong because + * during NF calibration, rx path is also routed to a detector, so if + * it doesn't finish we won't have RX. + * + * XXX: Find an interval that's OK for all cards... + */ ret = ath5k_hw_noise_floor_calibration(ah, channel->center_freq); if (ret) return ret; - ah->ah_calibration = false; - - /* A and G modes can use QAM modulation which requires enabling - * I and Q calibration. Don't bother in B mode. */ - if (!(mode == AR5K_MODE_11B)) { - ah->ah_calibration = true; - AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, - AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); - AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, - AR5K_PHY_IQ_RUN); - } - /* * Reset queues and start beacon timers at the end of the reset routine */ @@ -1154,6 +1192,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode, ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK); ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY); ath5k_hw_reg_write(ah, ah->ah_phy_spending, AR5K_PHY_SPENDING); + + data = ath5k_hw_reg_read(ah, AR5K_USEC_5211) & 0xffffc07f ; + data |= (ah->ah_phy_spending == AR5K_PHY_SPENDING_18) ? + 0x00000f80 : 0x00001380 ; + ath5k_hw_reg_write(ah, data, AR5K_USEC_5211); + data = 0; } if (ah->ah_version == AR5K_AR5212) { @@ -1226,7 +1270,7 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode, bool set_chip, u16 sleep_duration) { unsigned int i; - u32 staid; + u32 staid, data; ATH5K_TRACE(ah->ah_sc); staid = ath5k_hw_reg_read(ah, AR5K_STA_ID1); @@ -1238,7 +1282,8 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode, case AR5K_PM_NETWORK_SLEEP: if (set_chip) ath5k_hw_reg_write(ah, - AR5K_SLEEP_CTL_SLE | sleep_duration, + AR5K_SLEEP_CTL_SLE_ALLOW | + sleep_duration, AR5K_SLEEP_CTL); staid |= AR5K_STA_ID1_PWR_SV; @@ -1253,13 +1298,24 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode, break; case AR5K_PM_AWAKE: + + staid &= ~AR5K_STA_ID1_PWR_SV; + if (!set_chip) goto commit; - ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_WAKE, - AR5K_SLEEP_CTL); + /* Preserve sleep duration */ + data = ath5k_hw_reg_read(ah, AR5K_SLEEP_CTL); + if( data & 0xffc00000 ){ + data = 0; + } else { + data = data & 0xfffcffff; + } + + ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL); + udelay(15); - for (i = 5000; i > 0; i--) { + for (i = 50; i > 0; i--) { /* Check if the chip did wake up */ if ((ath5k_hw_reg_read(ah, AR5K_PCICFG) & AR5K_PCICFG_SPWR_DN) == 0) @@ -1267,15 +1323,13 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode, /* Wait a bit and retry */ udelay(200); - ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_WAKE, - AR5K_SLEEP_CTL); + ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL); } /* Fail if the chip didn't wake up */ if (i <= 0) return -EIO; - staid &= ~AR5K_STA_ID1_PWR_SV; break; default: @@ -1304,6 +1358,7 @@ void ath5k_hw_start_rx(struct ath5k_hw *ah) { ATH5K_TRACE(ah->ah_sc); ath5k_hw_reg_write(ah, AR5K_CR_RXE, AR5K_CR); + ath5k_hw_reg_read(ah, AR5K_CR); } /* @@ -1390,6 +1445,7 @@ int ath5k_hw_tx_start(struct ath5k_hw *ah, unsigned int queue) } /* Start queue */ ath5k_hw_reg_write(ah, tx_queue, AR5K_CR); + ath5k_hw_reg_read(ah, AR5K_CR); } else { /* Return if queue is disabled */ if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXD, queue)) @@ -1687,6 +1743,7 @@ enum ath5k_int ath5k_hw_set_intr(struct ath5k_hw *ah, enum ath5k_int new_mask) * (they will be re-enabled afterwards). */ ath5k_hw_reg_write(ah, AR5K_IER_DISABLE, AR5K_IER); + ath5k_hw_reg_read(ah, AR5K_IER); old_mask = ah->ah_imr; @@ -3363,11 +3420,13 @@ int ath5k_hw_reset_tx_queue(struct ath5k_hw *ah, unsigned int queue) ath5k_hw_reg_write(ah, ah->ah_turbo ? AR5K_INIT_PROTO_TIME_CNTRL_TURBO : AR5K_INIT_PROTO_TIME_CNTRL, AR5K_IFS1); - /* Set PHY register 0x9844 (??) */ + /* Set AR5K_PHY_SETTLING */ ath5k_hw_reg_write(ah, ah->ah_turbo ? - (ath5k_hw_reg_read(ah, AR5K_PHY(17)) & ~0x7F) | 0x38 : - (ath5k_hw_reg_read(ah, AR5K_PHY(17)) & ~0x7F) | 0x1C, - AR5K_PHY(17)); + (ath5k_hw_reg_read(ah, AR5K_PHY_SETTLING) & ~0x7F) + | 0x38 : + (ath5k_hw_reg_read(ah, AR5K_PHY_SETTLING) & ~0x7F) + | 0x1C, + AR5K_PHY_SETTLING); /* Set Frame Control Register */ ath5k_hw_reg_write(ah, ah->ah_turbo ? (AR5K_PHY_FRAME_CTL_INI | AR5K_PHY_TURBO_MODE | @@ -3488,7 +3547,7 @@ int ath5k_hw_reset_tx_queue(struct ath5k_hw *ah, unsigned int queue) if (tq->tqi_flags & AR5K_TXQ_FLAG_RDYTIME_EXP_POLICY_ENABLE) AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue), - AR5K_QCU_MISC_TXE); + AR5K_QCU_MISC_RDY_VEOL_POLICY); } if (tq->tqi_flags & AR5K_TXQ_FLAG_BACKOFF_DISABLE) diff --git a/drivers/net/wireless/ath5k/initvals.c b/drivers/net/wireless/ath5k/initvals.c index 04c84e9..2806b21 100644 --- a/drivers/net/wireless/ath5k/initvals.c +++ b/drivers/net/wireless/ath5k/initvals.c @@ -489,7 +489,7 @@ static const struct ath5k_ini ar5212_ini[] = { { AR5K_QUEUE_TXDP(9), 0x00000000 }, { AR5K_DCU_FP, 0x00000000 }, { AR5K_DCU_TXP, 0x00000000 }, - { AR5K_DCU_TX_FILTER, 0x00000000 }, + { AR5K_DCU_TX_FILTER_0_BASE, 0x00000000 }, /* Unknown table */ { 0x1078, 0x00000000 }, { 0x10b8, 0x00000000 }, @@ -679,7 +679,7 @@ static const struct ath5k_ini ar5212_ini[] = { { AR5K_PHY(645), 0x00106c10 }, { AR5K_PHY(646), 0x009c4060 }, { AR5K_PHY(647), 0x1483800a }, - /* { AR5K_PHY(648), 0x018830c6 },*/ /* 2413 */ + /* { AR5K_PHY(648), 0x018830c6 },*/ /* 2413/2425 */ { AR5K_PHY(648), 0x01831061 }, { AR5K_PHY(649), 0x00000400 }, /*{ AR5K_PHY(650), 0x000001b5 },*/ diff --git a/drivers/net/wireless/ath5k/phy.c b/drivers/net/wireless/ath5k/phy.c index afd8689..fa0d47f 100644 --- a/drivers/net/wireless/ath5k/phy.c +++ b/drivers/net/wireless/ath5k/phy.c @@ -1020,6 +1020,74 @@ static const struct ath5k_ini_rfgain rfgain_2413[] = { { AR5K_RF_GAIN(63), { 0x000000f9 } }, }; +/* Initial RF Gain settings for RF2425 */ +static const struct ath5k_ini_rfgain rfgain_2425[] = { + { AR5K_RF_GAIN(0), { 0x00000000 } }, + { AR5K_RF_GAIN(1), { 0x00000040 } }, + { AR5K_RF_GAIN(2), { 0x00000080 } }, + { AR5K_RF_GAIN(3), { 0x00000181 } }, + { AR5K_RF_GAIN(4), { 0x000001c1 } }, + { AR5K_RF_GAIN(5), { 0x00000001 } }, + { AR5K_RF_GAIN(6), { 0x00000041 } }, + { AR5K_RF_GAIN(7), { 0x00000081 } }, + { AR5K_RF_GAIN(8), { 0x00000188 } }, + { AR5K_RF_GAIN(9), { 0x000001c8 } }, + { AR5K_RF_GAIN(10), { 0x00000008 } }, + { AR5K_RF_GAIN(11), { 0x00000048 } }, + { AR5K_RF_GAIN(12), { 0x00000088 } }, + { AR5K_RF_GAIN(13), { 0x00000189 } }, + { AR5K_RF_GAIN(14), { 0x000001c9 } }, + { AR5K_RF_GAIN(15), { 0x00000009 } }, + { AR5K_RF_GAIN(16), { 0x00000049 } }, + { AR5K_RF_GAIN(17), { 0x00000089 } }, + { AR5K_RF_GAIN(18), { 0x000001b0 } }, + { AR5K_RF_GAIN(19), { 0x000001f0 } }, + { AR5K_RF_GAIN(20), { 0x00000030 } }, + { AR5K_RF_GAIN(21), { 0x00000070 } }, + { AR5K_RF_GAIN(22), { 0x00000171 } }, + { AR5K_RF_GAIN(23), { 0x000001b1 } }, + { AR5K_RF_GAIN(24), { 0x000001f1 } }, + { AR5K_RF_GAIN(25), { 0x00000031 } }, + { AR5K_RF_GAIN(26), { 0x00000071 } }, + { AR5K_RF_GAIN(27), { 0x000001b8 } }, + { AR5K_RF_GAIN(28), { 0x000001f8 } }, + { AR5K_RF_GAIN(29), { 0x00000038 } }, + { AR5K_RF_GAIN(30), { 0x00000078 } }, + { AR5K_RF_GAIN(31), { 0x000000b8 } }, + { AR5K_RF_GAIN(32), { 0x000001b9 } }, + { AR5K_RF_GAIN(33), { 0x000001f9 } }, + { AR5K_RF_GAIN(34), { 0x00000039 } }, + { AR5K_RF_GAIN(35), { 0x00000079 } }, + { AR5K_RF_GAIN(36), { 0x000000b9 } }, + { AR5K_RF_GAIN(37), { 0x000000f9 } }, + { AR5K_RF_GAIN(38), { 0x000000f9 } }, + { AR5K_RF_GAIN(39), { 0x000000f9 } }, + { AR5K_RF_GAIN(40), { 0x000000f9 } }, + { AR5K_RF_GAIN(41), { 0x000000f9 } }, + { AR5K_RF_GAIN(42), { 0x000000f9 } }, + { AR5K_RF_GAIN(43), { 0x000000f9 } }, + { AR5K_RF_GAIN(44), { 0x000000f9 } }, + { AR5K_RF_GAIN(45), { 0x000000f9 } }, + { AR5K_RF_GAIN(46), { 0x000000f9 } }, + { AR5K_RF_GAIN(47), { 0x000000f9 } }, + { AR5K_RF_GAIN(48), { 0x000000f9 } }, + { AR5K_RF_GAIN(49), { 0x000000f9 } }, + { AR5K_RF_GAIN(50), { 0x000000f9 } }, + { AR5K_RF_GAIN(51), { 0x000000f9 } }, + { AR5K_RF_GAIN(52), { 0x000000f9 } }, + { AR5K_RF_GAIN(53), { 0x000000f9 } }, + { AR5K_RF_GAIN(54), { 0x000000f9 } }, + { AR5K_RF_GAIN(55), { 0x000000f9 } }, + { AR5K_RF_GAIN(56), { 0x000000f9 } }, + { AR5K_RF_GAIN(57), { 0x000000f9 } }, + { AR5K_RF_GAIN(58), { 0x000000f9 } }, + { AR5K_RF_GAIN(59), { 0x000000f9 } }, + { AR5K_RF_GAIN(60), { 0x000000f9 } }, + { AR5K_RF_GAIN(61), { 0x000000f9 } }, + { AR5K_RF_GAIN(62), { 0x000000f9 } }, + { AR5K_RF_GAIN(63), { 0x000000f9 } }, +}; + static const struct ath5k_gain_opt rfgain_opt_5112 = { 1, 8, @@ -1588,8 +1656,8 @@ int ath5k_hw_rfgain(struct ath5k_hw *ah, unsigned int freq) freq = 0; /* only 2Ghz */ break; case AR5K_RF2425: - ath5k_rfg = rfgain_2413; - size = ARRAY_SIZE(rfgain_2413); + ath5k_rfg = rfgain_2425; + size = ARRAY_SIZE(rfgain_2425); freq = 0; /* only 2Ghz */ break; default: @@ -1830,9 +1898,6 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, data = data0 = data1 = data2 = 0; c = channel->center_freq; - /* - * Set the channel on the RF5112 or newer - */ if (c < 4800) { if (!((c - 2224) % 5)) { data0 = ((2 * (c - 704)) - 3040) / 10; @@ -1844,7 +1909,7 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, return -EINVAL; data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8); - } else { + } else if ((c - (c % 5)) != 2 || c > 5435) { if (!(c % 20) && c >= 5120) { data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); data2 = ath5k_hw_bitswap(3, 2); @@ -1856,6 +1921,9 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, data2 = ath5k_hw_bitswap(1, 2); } else return -EINVAL; + } else { + data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); + data2 = ath5k_hw_bitswap(0, 2); } data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001; @@ -1867,6 +1935,45 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah, } /* + * Set the channel on the RF2425 + */ +static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah, + struct ieee80211_channel *channel) +{ + u32 data, data0, data2; + u16 c; + + data = data0 = data2 = 0; + c = channel->center_freq; + + if (c < 4800) { + data0 = ath5k_hw_bitswap((c - 2272), 8); + data2 = 0; + /* ? 5GHz ? */ + } else if ((c - (c % 5)) != 2 || c > 5435) { + if (!(c % 20) && c < 5120) + data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8); + else if (!(c % 10)) + data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8); + else if (!(c % 5)) + data0 = ath5k_hw_bitswap((c - 4800) / 5, 8); + else + return -EINVAL; + data2 = ath5k_hw_bitswap(1, 2); + } else { + data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8); + data2 = ath5k_hw_bitswap(0, 2); + } + + data = (data0 << 4) | data2 << 2 | 0x1001; + + ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER); + ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5); + + return 0; +} + +/* * Set a channel on the radio chip */ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) @@ -1895,6 +2002,9 @@ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) case AR5K_RF5111: ret = ath5k_hw_rf5111_channel(ah, channel); break; + case AR5K_RF2425: + ret = ath5k_hw_rf2425_channel(ah, channel); + break; default: ret = ath5k_hw_rf5112_channel(ah, channel); break; @@ -1903,6 +2013,15 @@ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) if (ret) return ret; + /* Set JAPAN setting for channel 14 */ + if (channel->center_freq == 2484) { + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, + AR5K_PHY_CCKTXCTL_JAPAN); + } else { + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL, + AR5K_PHY_CCKTXCTL_WORLD); + } + ah->ah_current_channel.center_freq = channel->center_freq; ah->ah_current_channel.hw_value = channel->hw_value; ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false; @@ -1933,6 +2052,8 @@ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel) * http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL \ * &p=1&u=%2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7245893.PN.&OS=PN/7 * + * XXX: Since during noise floor calibration antennas are detached according to + * the patent, we should stop tx queues here. */ int ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq) @@ -1942,7 +2063,7 @@ ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq) s32 noise_floor; /* - * Enable noise floor calibration and wait until completion + * Enable noise floor calibration */ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_NF); @@ -1952,7 +2073,7 @@ ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq) if (ret) { ATH5K_ERR(ah->ah_sc, "noise floor calibration timeout (%uMHz)\n", freq); - return ret; + return -EAGAIN; } /* Wait until the noise floor is calibrated and read the value */ @@ -1974,7 +2095,7 @@ ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq) if (noise_floor > AR5K_TUNE_NOISE_FLOOR) { ATH5K_ERR(ah->ah_sc, "noise floor calibration failed (%uMHz)\n", freq); - return -EIO; + return -EAGAIN; } ah->ah_noise_floor = noise_floor; @@ -2087,38 +2208,66 @@ static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah, } /* - * Perform a PHY calibration on RF5111/5112 + * Perform a PHY calibration on RF5111/5112 and newer chips */ static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah, struct ieee80211_channel *channel) { u32 i_pwr, q_pwr; s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd; + int i; ATH5K_TRACE(ah->ah_sc); if (!ah->ah_calibration || - ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) + ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN) goto done; - ah->ah_calibration = false; + /* Calibration has finished, get the results and re-run */ + for (i = 0; i <= 10; i++) { + iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); + i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); + q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q); + } - iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR); - i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I); - q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q); i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7; - q_coffd = q_pwr >> 6; + q_coffd = q_pwr >> 7; + /* No correction */ if (i_coffd == 0 || q_coffd == 0) goto done; i_coff = ((-iq_corr) / i_coffd) & 0x3f; - q_coff = (((s32)i_pwr / q_coffd) - 64) & 0x1f; - /* Commit new IQ value */ + /* Boundary check */ + if (i_coff > 31) + i_coff = 31; + if (i_coff < -32) + i_coff = -32; + + q_coff = (((s32)i_pwr / q_coffd) - 128) & 0x1f; + + /* Boundary check */ + if (q_coff > 15) + q_coff = 15; + if (q_coff < -16) + q_coff = -16; + + /* Commit new I/Q value */ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE | ((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S)); + /* Re-enable calibration -if we don't we'll commit + * the same values again and again */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, + AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15); + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN); + done: + + /* TODO: Separate noise floor calibration from I/Q calibration + * since noise floor calibration interrupts rx path while I/Q + * calibration doesn't. We don't need to run noise floor calibration + * as often as I/Q calibration.*/ ath5k_hw_noise_floor_calibration(ah, channel->center_freq); /* Request RF gain */ diff --git a/drivers/net/wireless/ath5k/reg.h b/drivers/net/wireless/ath5k/reg.h index 30629b3..7562bf1 100644 --- a/drivers/net/wireless/ath5k/reg.h +++ b/drivers/net/wireless/ath5k/reg.h @@ -53,7 +53,7 @@ #define AR5K_CR_TXD0 0x00000008 /* TX Disable for queue 0 on 5210 */ #define AR5K_CR_TXD1 0x00000010 /* TX Disable for queue 1 on 5210 */ #define AR5K_CR_RXD 0x00000020 /* RX Disable */ -#define AR5K_CR_SWI 0x00000040 +#define AR5K_CR_SWI 0x00000040 /* Software Interrupt */ /* * RX Descriptor Pointer register @@ -65,19 +65,19 @@ */ #define AR5K_CFG 0x0014 /* Register Address */ #define AR5K_CFG_SWTD 0x00000001 /* Byte-swap TX descriptor (for big endian archs) */ -#define AR5K_CFG_SWTB 0x00000002 /* Byte-swap TX buffer (?) */ +#define AR5K_CFG_SWTB 0x00000002 /* Byte-swap TX buffer */ #define AR5K_CFG_SWRD 0x00000004 /* Byte-swap RX descriptor */ -#define AR5K_CFG_SWRB 0x00000008 /* Byte-swap RX buffer (?) */ -#define AR5K_CFG_SWRG 0x00000010 /* Byte-swap Register values (?) */ -#define AR5K_CFG_ADHOC 0x00000020 /* [5211+] */ +#define AR5K_CFG_SWRB 0x00000008 /* Byte-swap RX buffer */ +#define AR5K_CFG_SWRG 0x00000010 /* Byte-swap Register access */ +#define AR5K_CFG_ADHOC 0x00000020 /* AP/Adhoc indication [5211+] */ #define AR5K_CFG_PHY_OK 0x00000100 /* [5211+] */ #define AR5K_CFG_EEBS 0x00000200 /* EEPROM is busy */ -#define AR5K_CFG_CLKGD 0x00000400 /* Clock gated (?) */ +#define AR5K_CFG_CLKGD 0x00000400 /* Clock gated (Disable dynamic clock) */ #define AR5K_CFG_TXCNT 0x00007800 /* Tx frame count (?) [5210] */ #define AR5K_CFG_TXCNT_S 11 #define AR5K_CFG_TXFSTAT 0x00008000 /* Tx frame status (?) [5210] */ #define AR5K_CFG_TXFSTRT 0x00010000 /* [5210] */ -#define AR5K_CFG_PCI_THRES 0x00060000 /* [5211+] */ +#define AR5K_CFG_PCI_THRES 0x00060000 /* PCI Master req q threshold [5211+] */ #define AR5K_CFG_PCI_THRES_S 17 /* @@ -162,35 +162,40 @@ /* * Transmit configuration register */ -#define AR5K_TXCFG 0x0030 /* Register Address */ -#define AR5K_TXCFG_SDMAMR 0x00000007 /* DMA size */ -#define AR5K_TXCFG_SDMAMR_S 0 -#define AR5K_TXCFG_B_MODE 0x00000008 /* Set b mode for 5111 (enable 2111) */ -#define AR5K_TXCFG_TXFSTP 0x00000008 /* TX DMA full Stop [5210] */ -#define AR5K_TXCFG_TXFULL 0x000003f0 /* TX Triger level mask */ -#define AR5K_TXCFG_TXFULL_S 4 -#define AR5K_TXCFG_TXFULL_0B 0x00000000 -#define AR5K_TXCFG_TXFULL_64B 0x00000010 -#define AR5K_TXCFG_TXFULL_128B 0x00000020 -#define AR5K_TXCFG_TXFULL_192B 0x00000030 -#define AR5K_TXCFG_TXFULL_256B 0x00000040 -#define AR5K_TXCFG_TXCONT_EN 0x00000080 -#define AR5K_TXCFG_DMASIZE 0x00000100 /* Flag for passing DMA size [5210] */ -#define AR5K_TXCFG_JUMBO_TXE 0x00000400 /* Enable jumbo frames transmition (?) [5211+] */ -#define AR5K_TXCFG_RTSRND 0x00001000 /* [5211+] */ -#define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */ -#define AR5K_TXCFG_RDY_DIS 0x00004000 /* [5211+] */ +#define AR5K_TXCFG 0x0030 /* Register Address */ +#define AR5K_TXCFG_SDMAMR 0x00000007 /* DMA size (read) */ +#define AR5K_TXCFG_SDMAMR_S 0 +#define AR5K_TXCFG_B_MODE 0x00000008 /* Set b mode for 5111 (enable 2111) */ +#define AR5K_TXCFG_TXFSTP 0x00000008 /* TX DMA full Stop [5210] */ +#define AR5K_TXCFG_TXFULL 0x000003f0 /* TX Triger level mask */ +#define AR5K_TXCFG_TXFULL_S 4 +#define AR5K_TXCFG_TXFULL_0B 0x00000000 +#define AR5K_TXCFG_TXFULL_64B 0x00000010 +#define AR5K_TXCFG_TXFULL_128B 0x00000020 +#define AR5K_TXCFG_TXFULL_192B 0x00000030 +#define AR5K_TXCFG_TXFULL_256B 0x00000040 +#define AR5K_TXCFG_TXCONT_EN 0x00000080 +#define AR5K_TXCFG_DMASIZE 0x00000100 /* Flag for passing DMA size [5210] */ +#define AR5K_TXCFG_JUMBO_DESC_EN 0x00000400 /* Enable jumbo tx descriptors [5211+] */ +#define AR5K_TXCFG_ADHOC_BCN_ATIM 0x00000800 /* Adhoc Beacon ATIM Policy */ +#define AR5K_TXCFG_ATIM_WINDOW_DEF_DIS 0x00001000 /* Disable ATIM window defer [5211+] */ +#define AR5K_TXCFG_RTSRND 0x00001000 /* [5211+] */ +#define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */ +#define AR5K_TXCFG_RDY_CBR_DIS 0x00004000 /* Ready time CBR disable [5211+] */ +#define AR5K_TXCFG_JUMBO_FRM_MODE 0x00008000 /* Jumbo frame mode [5211+] */ +#define AR5K_TXCFG_DCU_CACHING_DIS 0x00010000 /* Disable DCU caching */ /* * Receive configuration register */ #define AR5K_RXCFG 0x0034 /* Register Address */ -#define AR5K_RXCFG_SDMAMW 0x00000007 /* DMA size */ +#define AR5K_RXCFG_SDMAMW 0x00000007 /* DMA size (write) */ #define AR5K_RXCFG_SDMAMW_S 0 -#define AR5K_RXCFG_DEF_ANTENNA 0x00000008 /* Default antenna */ -#define AR5K_RXCFG_ZLFDMA 0x00000010 /* Zero-length DMA */ -#define AR5K_RXCFG_JUMBO_RXE 0x00000020 /* Enable jumbo frames reception (?) [5211+] */ -#define AR5K_RXCFG_JUMBO_WRAP 0x00000040 /* Wrap jumbo frames (?) [5211+] */ +#define AR5K_RXCFG_ZLFDMA 0x00000008 /* Enable Zero-length frame DMA */ +#define AR5K_RXCFG_DEF_ANTENNA 0x00000010 /* Default antenna (?) */ +#define AR5K_RXCFG_JUMBO_RXE 0x00000020 /* Enable jumbo rx descriptors [5211+] */ +#define AR5K_RXCFG_JUMBO_WRAP 0x00000040 /* Wrap jumbo frames [5211+] */ +#define AR5K_RXCFG_SLE_ENTRY 0x00000080 /* Sleep entry policy */ /* * Receive jumbo descriptor last address register @@ -202,35 +207,35 @@ * MIB control register */ #define AR5K_MIBC 0x0040 /* Register Address */ -#define AR5K_MIBC_COW 0x00000001 -#define AR5K_MIBC_FMC 0x00000002 /* Freeze Mib Counters (?) */ -#define AR5K_MIBC_CMC 0x00000004 /* Clean Mib Counters (?) */ -#define AR5K_MIBC_MCS 0x00000008 +#define AR5K_MIBC_COW 0x00000001 /* Warn test indicator */ +#define AR5K_MIBC_FMC 0x00000002 /* Freeze MIB Counters */ +#define AR5K_MIBC_CMC 0x00000004 /* Clean MIB Counters */ +#define AR5K_MIBC_MCS 0x00000008 /* MIB counter strobe */ /* * Timeout prescale register */ #define AR5K_TOPS 0x0044 -#define AR5K_TOPS_M 0x0000ffff /* [5211+] (?) */ +#define AR5K_TOPS_M 0x0000ffff /* * Receive timeout register (no frame received) */ #define AR5K_RXNOFRM 0x0048 -#define AR5K_RXNOFRM_M 0x000003ff /* [5211+] (?) */ +#define AR5K_RXNOFRM_M 0x000003ff /* * Transmit timeout register (no frame sent) */ #define AR5K_TXNOFRM 0x004c -#define AR5K_TXNOFRM_M 0x000003ff /* [5211+] (?) */ -#define AR5K_TXNOFRM_QCU 0x000ffc00 /* [5211+] (?) */ +#define AR5K_TXNOFRM_M 0x000003ff +#define AR5K_TXNOFRM_QCU 0x000ffc00 /* * Receive frame gap timeout register */ #define AR5K_RPGTO 0x0050 -#define AR5K_RPGTO_M 0x000003ff /* [5211+] (?) */ +#define AR5K_RPGTO_M 0x000003ff /* * Receive frame count limit register @@ -241,6 +246,7 @@ /* * Misc settings register + * (reserved0-3) */ #define AR5K_MISC 0x0058 /* Register Address */ #define AR5K_MISC_DMA_OBS_M 0x000001e0 @@ -256,6 +262,7 @@ /* * QCU/DCU clock gating register (5311) + * (reserved4-5) */ #define AR5K_QCUDCU_CLKGT 0x005c /* Register Address (?) */ #define AR5K_QCUDCU_CLKGT_QCU 0x0000ffff /* Mask for QCU clock */ @@ -284,18 +291,18 @@ #define AR5K_ISR_TXEOL 0x00000400 /* Empty TX descriptor */ #define AR5K_ISR_TXURN 0x00000800 /* Transmit FIFO underrun */ #define AR5K_ISR_MIB 0x00001000 /* Update MIB counters */ -#define AR5K_ISR_SWI 0x00002000 /* Software interrupt (?) */ +#define AR5K_ISR_SWI 0x00002000 /* Software interrupt */ #define AR5K_ISR_RXPHY 0x00004000 /* PHY error */ -#define AR5K_ISR_RXKCM 0x00008000 +#define AR5K_ISR_RXKCM 0x00008000 /* RX Key cache miss */ #define AR5K_ISR_SWBA 0x00010000 /* Software beacon alert */ #define AR5K_ISR_BRSSI 0x00020000 #define AR5K_ISR_BMISS 0x00040000 /* Beacon missed */ #define AR5K_ISR_HIUERR 0x00080000 /* Host Interface Unit error [5211+] */ #define AR5K_ISR_BNR 0x00100000 /* Beacon not ready [5211+] */ -#define AR5K_ISR_MCABT 0x00100000 /* [5210] */ -#define AR5K_ISR_RXCHIRP 0x00200000 /* [5212+] */ -#define AR5K_ISR_SSERR 0x00200000 /* [5210] */ -#define AR5K_ISR_DPERR 0x00400000 /* [5210] */ +#define AR5K_ISR_MCABT 0x00100000 /* Master Cycle Abort [5210] */ +#define AR5K_ISR_RXCHIRP 0x00200000 /* CHIRP Received [5212+] */ +#define AR5K_ISR_SSERR 0x00200000 /* Signaled System Error [5210] */ +#define AR5K_ISR_DPERR 0x00400000 /* Det par Error (?) [5210] */ #define AR5K_ISR_TIM 0x00800000 /* [5210] */ #define AR5K_ISR_BCNMISC 0x00800000 /* [5212+] */ #define AR5K_ISR_GPIO 0x01000000 /* GPIO (rf kill)*/ @@ -320,14 +327,14 @@ #define AR5K_SISR2 0x008c /* Register Address [5211+] */ #define AR5K_SISR2_QCU_TXURN 0x000003ff /* Mask for QCU_TXURN */ -#define AR5K_SISR2_MCABT 0x00100000 -#define AR5K_SISR2_SSERR 0x00200000 -#define AR5K_SISR2_DPERR 0x00400000 +#define AR5K_SISR2_MCABT 0x00100000 /* Master Cycle Abort */ +#define AR5K_SISR2_SSERR 0x00200000 /* Signaled System Error */ +#define AR5K_SISR2_DPERR 0x00400000 /* Det par Error (?) */ #define AR5K_SISR2_TIM 0x01000000 /* [5212+] */ #define AR5K_SISR2_CAB_END 0x02000000 /* [5212+] */ -#define AR5K_SISR2_DTIM_SYNC 0x04000000 /* [5212+] */ -#define AR5K_SISR2_BCN_TIMEOUT 0x08000000 /* [5212+] */ -#define AR5K_SISR2_CAB_TIMEOUT 0x10000000 /* [5212+] */ +#define AR5K_SISR2_DTIM_SYNC 0x04000000 /* DTIM sync lost [5212+] */ +#define AR5K_SISR2_BCN_TIMEOUT 0x08000000 /* Beacon Timeout [5212+] */ +#define AR5K_SISR2_CAB_TIMEOUT 0x10000000 /* CAB Timeout [5212+] */ #define AR5K_SISR2_DTIM 0x20000000 /* [5212+] */ #define AR5K_SISR3 0x0090 /* Register Address [5211+] */ @@ -368,18 +375,18 @@ #define AR5K_IMR_TXEOL 0x00000400 /* Empty TX descriptor*/ #define AR5K_IMR_TXURN 0x00000800 /* Transmit FIFO underrun*/ #define AR5K_IMR_MIB 0x00001000 /* Update MIB counters*/ -#define AR5K_IMR_SWI 0x00002000 +#define AR5K_IMR_SWI 0x00002000 /* Software interrupt */ #define AR5K_IMR_RXPHY 0x00004000 /* PHY error*/ -#define AR5K_IMR_RXKCM 0x00008000 +#define AR5K_IMR_RXKCM 0x00008000 /* RX Key cache miss */ #define AR5K_IMR_SWBA 0x00010000 /* Software beacon alert*/ #define AR5K_IMR_BRSSI 0x00020000 #define AR5K_IMR_BMISS 0x00040000 /* Beacon missed*/ #define AR5K_IMR_HIUERR 0x00080000 /* Host Interface Unit error [5211+] */ #define AR5K_IMR_BNR 0x00100000 /* Beacon not ready [5211+] */ -#define AR5K_IMR_MCABT 0x00100000 /* [5210] */ -#define AR5K_IMR_RXCHIRP 0x00200000 /* [5212+]*/ -#define AR5K_IMR_SSERR 0x00200000 /* [5210] */ -#define AR5K_IMR_DPERR 0x00400000 /* [5210] */ +#define AR5K_IMR_MCABT 0x00100000 /* Master Cycle Abort [5210] */ +#define AR5K_IMR_RXCHIRP 0x00200000 /* CHIRP Received [5212+]*/ +#define AR5K_IMR_SSERR 0x00200000 /* Signaled System Error [5210] */ +#define AR5K_IMR_DPERR 0x00400000 /* Det par Error (?) [5210] */ #define AR5K_IMR_TIM 0x00800000 /* [5211+] */ #define AR5K_IMR_BCNMISC 0x00800000 /* [5212+] */ #define AR5K_IMR_GPIO 0x01000000 /* GPIO (rf kill)*/ @@ -405,14 +412,14 @@ #define AR5K_SIMR2 0x00ac /* Register Address [5211+] */ #define AR5K_SIMR2_QCU_TXURN 0x000003ff /* Mask for QCU_TXURN */ #define AR5K_SIMR2_QCU_TXURN_S 0 -#define AR5K_SIMR2_MCABT 0x00100000 -#define AR5K_SIMR2_SSERR 0x00200000 -#define AR5K_SIMR2_DPERR 0x00400000 +#define AR5K_SIMR2_MCABT 0x00100000 /* Master Cycle Abort */ +#define AR5K_SIMR2_SSERR 0x00200000 /* Signaled System Error */ +#define AR5K_SIMR2_DPERR 0x00400000 /* Det par Error (?) */ #define AR5K_SIMR2_TIM 0x01000000 /* [5212+] */ #define AR5K_SIMR2_CAB_END 0x02000000 /* [5212+] */ -#define AR5K_SIMR2_DTIM_SYNC 0x04000000 /* [5212+] */ -#define AR5K_SIMR2_BCN_TIMEOUT 0x08000000 /* [5212+] */ -#define AR5K_SIMR2_CAB_TIMEOUT 0x10000000 /* [5212+] */ +#define AR5K_SIMR2_DTIM_SYNC 0x04000000 /* DTIM Sync lost [5212+] */ +#define AR5K_SIMR2_BCN_TIMEOUT 0x08000000 /* Beacon Timeout [5212+] */ +#define AR5K_SIMR2_CAB_TIMEOUT 0x10000000 /* CAB Timeout [5212+] */ #define AR5K_SIMR2_DTIM 0x20000000 /* [5212+] */ #define AR5K_SIMR3 0x00b0 /* Register Address [5211+] */ @@ -425,23 +432,69 @@ #define AR5K_SIMR4_QTRIG 0x000003ff /* Mask for QTRIG */ #define AR5K_SIMR4_QTRIG_S 0 +/* + * DMA Debug registers 0-7 + * 0xe0 - 0xfc + */ /* * Decompression mask registers [5212+] */ -#define AR5K_DCM_ADDR 0x0400 /*Decompression mask address (?)*/ -#define AR5K_DCM_DATA 0x0404 /*Decompression mask data (?)*/ +#define AR5K_DCM_ADDR 0x0400 /*Decompression mask address (index) */ +#define AR5K_DCM_DATA 0x0404 /*Decompression mask data */ + +/* + * Wake On Wireless pattern control register [5212+] + */ +#define AR5K_WOW_PCFG 0x0410 /* Register Address */ +#define AR5K_WOW_PCFG_PAT_MATCH_EN 0x00000001 /* Pattern match enable */ +#define AR5K_WOW_PCFG_LONG_FRAME_POL 0x00000002 /* Long frame policy */ +#define AR5K_WOW_PCFG_WOBMISS 0x00000004 /* Wake on bea(con) miss (?) */ +#define AR5K_WOW_PCFG_PAT_0_EN 0x00000100 /* Enable pattern 0 */ +#define AR5K_WOW_PCFG_PAT_1_EN 0x00000200 /* Enable pattern 1 */ +#define AR5K_WOW_PCFG_PAT_2_EN 0x00000400 /* Enable pattern 2 */ +#define AR5K_WOW_PCFG_PAT_3_EN 0x00000800 /* Enable pattern 3 */ +#define AR5K_WOW_PCFG_PAT_4_EN 0x00001000 /* Enable pattern 4 */ +#define AR5K_WOW_PCFG_PAT_5_EN 0x00002000 /* Enable pattern 5 */ + +/* + * Wake On Wireless pattern index register (?) [5212+] + */ +#define AR5K_WOW_PAT_IDX 0x0414 + +/* + * Wake On Wireless pattern data register [5212+] + */ +#define AR5K_WOW_PAT_DATA 0x0418 /* Register Address */ +#define AR5K_WOW_PAT_DATA_0_3_V 0x00000001 /* Pattern 0, 3 value */ +#define AR5K_WOW_PAT_DATA_1_4_V 0x00000100 /* Pattern 1, 4 value */ +#define AR5K_WOW_PAT_DATA_2_5_V 0x00010000 /* Pattern 2, 5 value */ +#define AR5K_WOW_PAT_DATA_0_3_M 0x01000000 /* Pattern 0, 3 mask */ +#define AR5K_WOW_PAT_DATA_1_4_M 0x04000000 /* Pattern 1, 4 mask */ +#define AR5K_WOW_PAT_DATA_2_5_M 0x10000000 /* Pattern 2, 5 mask */ /* * Decompression configuration registers [5212+] */ -#define AR5K_DCCFG 0x0420 +#define AR5K_DCCFG 0x0420 /* Register Address */ +#define AR5K_DCCFG_GLOBAL_EN 0x00000001 /* Enable decompression on all queues */ +#define AR5K_DCCFG_BYPASS_EN 0x00000002 /* Bypass decompression */ +#define AR5K_DCCFG_BCAST_EN 0x00000004 /* Enable decompression for bcast frames */ +#define AR5K_DCCFG_MCAST_EN 0x00000008 /* Enable decompression for mcast frames */ /* * Compression configuration registers [5212+] */ -#define AR5K_CCFG 0x0600 -#define AR5K_CCFG_CUP 0x0604 +#define AR5K_CCFG 0x0600 /* Register Address */ +#define AR5K_CCFG_WINDOW_SIZE 0x00000007 /* Compression window size */ +#define AR5K_CCFG_CPC_EN 0x00000008 /* Enable performance counters */ + +#define AR5K_CCFG_CCU 0x0604 /* Register Address */ +#define AR5K_CCFG_CCU_CUP_EN 0x00000001 /* CCU Catchup enable */ +#define AR5K_CCFG_CCU_CREDIT 0x00000002 /* CCU Credit (field) */ +#define AR5K_CCFG_CCU_CD_THRES 0x00000080 /* CCU Cyc(lic?) debt threshold (field) */ +#define AR5K_CCFG_CCU_CUP_LCNT 0x00010000 /* CCU Catchup lit(?) count */ +#define AR5K_CCFG_CCU_INIT 0x00100200 /* Initial value during reset */ /* * Compression performance counter registers [5212+] @@ -450,7 +503,7 @@ #define AR5K_CPC1 0x0614 /* Compression performance counter 1*/ #define AR5K_CPC2 0x0618 /* Compression performance counter 2 */ #define AR5K_CPC3 0x061c /* Compression performance counter 3 */ -#define AR5K_CPCORN 0x0620 /* Compression performance overrun (?) */ +#define AR5K_CPCOVF 0x0620 /* Compression performance overflow */ /* @@ -466,8 +519,6 @@ * set/clear, which contain status for all queues (we shift by 1 for each * queue). To access these registers easily we define some macros here * that are used inside HAL. For more infos check out *_tx_queue functs. - * - * TODO: Boundary checking on macros (here?) */ /* @@ -513,7 +564,6 @@ #define AR5K_QCU_RDYTIMECFG_BASE 0x0900 /* Register Address - Queue0 RDYTIMECFG */ #define AR5K_QCU_RDYTIMECFG_INTVAL 0x00ffffff /* Ready time interval mask */ #define AR5K_QCU_RDYTIMECFG_INTVAL_S 0 -#define AR5K_QCU_RDYTIMECFG_DURATION 0x00ffffff /* Ready time duration mask */ #define AR5K_QCU_RDYTIMECFG_ENABLE 0x01000000 /* Ready time enable mask */ #define AR5K_QUEUE_RDYTIMECFG(_q) AR5K_QUEUE_REG(AR5K_QCU_RDYTIMECFG_BASE, _q) @@ -534,19 +584,20 @@ */ #define AR5K_QCU_MISC_BASE 0x09c0 /* Register Address -Queue0 MISC */ #define AR5K_QCU_MISC_FRSHED_M 0x0000000f /* Frame sheduling mask */ -#define AR5K_QCU_MISC_FRSHED_ASAP 0 /* ASAP */ -#define AR5K_QCU_MISC_FRSHED_CBR 1 /* Constant Bit Rate */ -#define AR5K_QCU_MISC_FRSHED_DBA_GT 2 /* DMA Beacon alert gated (?) */ -#define AR5K_QCU_MISC_FRSHED_TIM_GT 3 /* Time gated (?) */ +#define AR5K_QCU_MISC_FRSHED_ASAP 0 /* ASAP */ +#define AR5K_QCU_MISC_FRSHED_CBR 1 /* Constant Bit Rate */ +#define AR5K_QCU_MISC_FRSHED_DBA_GT 2 /* DMA Beacon alert gated (?) */ +#define AR5K_QCU_MISC_FRSHED_TIM_GT 3 /* Time gated (?) */ #define AR5K_QCU_MISC_FRSHED_BCN_SENT_GT 4 /* Beacon sent gated (?) */ #define AR5K_QCU_MISC_ONESHOT_ENABLE 0x00000010 /* Oneshot enable */ #define AR5K_QCU_MISC_CBREXP 0x00000020 /* CBR expired (normal queue) */ #define AR5K_QCU_MISC_CBREXP_BCN 0x00000040 /* CBR expired (beacon queue) */ -#define AR5K_QCU_MISC_BCN_ENABLE 0x00000080 /* Beacons enabled */ -#define AR5K_QCU_MISC_CBR_THRES_ENABLE 0x00000100 /* CBR threshold enabled (?) */ -#define AR5K_QCU_MISC_TXE 0x00000200 /* TXE reset when RDYTIME enalbed (?) */ -#define AR5K_QCU_MISC_CBR 0x00000400 /* CBR threshold reset (?) */ -#define AR5K_QCU_MISC_DCU_EARLY 0x00000800 /* DCU reset (?) */ +#define AR5K_QCU_MISC_BCN_ENABLE 0x00000080 /* Enable Beacon use */ +#define AR5K_QCU_MISC_CBR_THRES_ENABLE 0x00000100 /* CBR threshold enabled */ +#define AR5K_QCU_MISC_RDY_VEOL_POLICY 0x00000200 /* TXE reset when RDYTIME enalbed */ +#define AR5K_QCU_MISC_CBR_RESET_CNT 0x00000400 /* CBR threshold (counter) reset */ +#define AR5K_QCU_MISC_DCU_EARLY 0x00000800 /* DCU early termination */ +#define AR5K_QCU_MISC_DCU_CMP_EN 0x00001000 /* Enable frame compression */ #define AR5K_QUEUE_MISC(_q) AR5K_QUEUE_REG(AR5K_QCU_MISC_BASE, _q) @@ -555,7 +606,7 @@ */ #define AR5K_QCU_STS_BASE 0x0a00 /* Register Address - Queue0 STS */ #define AR5K_QCU_STS_FRMPENDCNT 0x00000003 /* Frames pending counter */ -#define AR5K_QCU_STS_CBREXPCNT 0x0000ff00 /* CBR expired counter (?) */ +#define AR5K_QCU_STS_CBREXPCNT 0x0000ff00 /* CBR expired counter */ #define AR5K_QUEUE_STATUS(_q) AR5K_QUEUE_REG(AR5K_QCU_STS_BASE, _q) /* @@ -569,9 +620,11 @@ */ #define AR5K_QCU_CBB_SELECT 0x0b00 #define AR5K_QCU_CBB_ADDR 0x0b04 +#define AR5K_QCU_CBB_ADDR_S 9 /* * QCU compression buffer configuration register [5212+] + * (buffer size) */ #define AR5K_QCU_CBCFG 0x0b08 @@ -652,80 +705,100 @@ * No lockout means there is no special handling. */ #define AR5K_DCU_MISC_BASE 0x1100 /* Register Address -Queue0 DCU_MISC */ -#define AR5K_DCU_MISC_BACKOFF 0x000007ff /* Mask for backoff setting (?) */ +#define AR5K_DCU_MISC_BACKOFF 0x000007ff /* Mask for backoff threshold */ #define AR5K_DCU_MISC_BACKOFF_FRAG 0x00000200 /* Enable backoff while bursting */ -#define AR5K_DCU_MISC_HCFPOLL_ENABLE 0x00000800 /* CF - Poll (?) */ -#define AR5K_DCU_MISC_BACKOFF_PERSIST 0x00001000 /* Persistent backoff (?) */ -#define AR5K_DCU_MISC_FRMPRFTCH_ENABLE 0x00002000 /* Enable frame pre-fetch (?) */ +#define AR5K_DCU_MISC_HCFPOLL_ENABLE 0x00000800 /* CF - Poll enable */ +#define AR5K_DCU_MISC_BACKOFF_PERSIST 0x00001000 /* Persistent backoff */ +#define AR5K_DCU_MISC_FRMPRFTCH_ENABLE 0x00002000 /* Enable frame pre-fetch */ #define AR5K_DCU_MISC_VIRTCOL 0x0000c000 /* Mask for Virtual Collision (?) */ -#define AR5K_DCU_MISC_VIRTCOL_NORMAL 0 -#define AR5K_DCU_MISC_VIRTCOL_MODIFIED 1 -#define AR5K_DCU_MISC_VIRTCOL_IGNORE 2 -#define AR5K_DCU_MISC_BCN_ENABLE 0x00010000 /* Beacon enable (?) */ +#define AR5K_DCU_MISC_VIRTCOL_NORMAL 0 +#define AR5K_DCU_MISC_VIRTCOL_MODIFIED 1 +#define AR5K_DCU_MISC_VIRTCOL_IGNORE 2 +#define AR5K_DCU_MISC_BCN_ENABLE 0x00010000 /* Enable Beacon use */ #define AR5K_DCU_MISC_ARBLOCK_CTL 0x00060000 /* Arbiter lockout control mask */ #define AR5K_DCU_MISC_ARBLOCK_CTL_S 17 -#define AR5K_DCU_MISC_ARBLOCK_CTL_NONE 0 /* No arbiter lockout */ +#define AR5K_DCU_MISC_ARBLOCK_CTL_NONE 0 /* No arbiter lockout */ #define AR5K_DCU_MISC_ARBLOCK_CTL_INTFRM 1 /* Intra-frame lockout */ #define AR5K_DCU_MISC_ARBLOCK_CTL_GLOBAL 2 /* Global lockout */ -#define AR5K_DCU_MISC_ARBLOCK_IGNORE 0x00080000 -#define AR5K_DCU_MISC_SEQ_NUM_INCR_DIS 0x00100000 /* Disable sequence number increment (?) */ -#define AR5K_DCU_MISC_POST_FR_BKOFF_DIS 0x00200000 /* Disable post-frame backoff (?) */ -#define AR5K_DCU_MISC_VIRT_COLL_POLICY 0x00400000 /* Virtual Collision policy (?) */ -#define AR5K_DCU_MISC_BLOWN_IFS_POLICY 0x00800000 +#define AR5K_DCU_MISC_ARBLOCK_IGNORE 0x00080000 /* Ignore Arbiter lockout */ +#define AR5K_DCU_MISC_SEQ_NUM_INCR_DIS 0x00100000 /* Disable sequence number increment */ +#define AR5K_DCU_MISC_POST_FR_BKOFF_DIS 0x00200000 /* Disable post-frame backoff */ +#define AR5K_DCU_MISC_VIRT_COLL_POLICY 0x00400000 /* Virtual Collision cw policy */ +#define AR5K_DCU_MISC_BLOWN_IFS_POLICY 0x00800000 /* Blown IFS policy (?) */ #define AR5K_DCU_MISC_SEQNUM_CTL 0x01000000 /* Sequence number control (?) */ #define AR5K_QUEUE_DFS_MISC(_q) AR5K_QUEUE_REG(AR5K_DCU_MISC_BASE, _q) /* * DCU frame sequence number registers */ -#define AR5K_DCU_SEQNUM_BASE 0x1140 -#define AR5K_DCU_SEQNUM_M 0x00000fff +#define AR5K_DCU_SEQNUM_BASE 0x1140 +#define AR5K_DCU_SEQNUM_M 0x00000fff #define AR5K_QUEUE_DFS_SEQNUM(_q) AR5K_QUEUE_REG(AR5K_DCU_SEQNUM_BASE, _q) /* - * DCU global IFS SIFS registers + * DCU global IFS SIFS register */ #define AR5K_DCU_GBL_IFS_SIFS 0x1030 #define AR5K_DCU_GBL_IFS_SIFS_M 0x0000ffff /* - * DCU global IFS slot interval registers + * DCU global IFS slot interval register */ #define AR5K_DCU_GBL_IFS_SLOT 0x1070 #define AR5K_DCU_GBL_IFS_SLOT_M 0x0000ffff /* - * DCU global IFS EIFS registers + * DCU global IFS EIFS register */ #define AR5K_DCU_GBL_IFS_EIFS 0x10b0 #define AR5K_DCU_GBL_IFS_EIFS_M 0x0000ffff /* - * DCU global IFS misc registers + * DCU global IFS misc register + * + * LFSR stands for Linear Feedback Shift Register + * and it's used for generating pseudo-random + * number sequences. + * + * (If i understand corectly, random numbers are + * used for idle sensing -multiplied with cwmin/max etc-) */ #define AR5K_DCU_GBL_IFS_MISC 0x10f0 /* Register Address */ -#define AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE 0x00000007 -#define AR5K_DCU_GBL_IFS_MISC_TURBO_MODE 0x00000008 /* Turbo mode (?) */ -#define AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC 0x000003f0 /* SIFS Duration mask (?) */ -#define AR5K_DCU_GBL_IFS_MISC_USEC_DUR 0x000ffc00 -#define AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY 0x00300000 +#define AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE 0x00000007 /* LFSR Slice Select */ +#define AR5K_DCU_GBL_IFS_MISC_TURBO_MODE 0x00000008 /* Turbo mode */ +#define AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC 0x000003f0 /* SIFS Duration mask */ +#define AR5K_DCU_GBL_IFS_MISC_USEC_DUR 0x000ffc00 /* USEC Duration mask */ +#define AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY 0x00300000 /* DCU Arbiter delay mask */ +#define AR5K_DCU_GBL_IFS_MISC_SIFS_CNT_RST 0x00400000 /* SIFC cnt reset policy (?) */ +#define AR5K_DCU_GBL_IFS_MISC_AIFS_CNT_RST 0x00800000 /* AIFS cnt reset policy (?) */ +#define AR5K_DCU_GBL_IFS_MISC_RND_LFSR_SL_DIS 0x01000000 /* Disable random LFSR slice */ /* * DCU frame prefetch control register */ -#define AR5K_DCU_FP 0x1230 +#define AR5K_DCU_FP 0x1230 /* Register Address */ +#define AR5K_DCU_FP_NOBURST_DCU_EN 0x00000001 /* Enable non-burst prefetch on DCU (?) */ +#define AR5K_DCU_FP_NOBURST_EN 0x00000010 /* Enable non-burst prefetch (?) */ +#define AR5K_DCU_FP_BURST_DCU_EN 0x00000020 /* Enable burst prefetch on DCU (?) */ /* * DCU transmit pause control/status register */ #define AR5K_DCU_TXP 0x1270 /* Register Address */ -#define AR5K_DCU_TXP_M 0x000003ff /* Tx pause mask (?) */ -#define AR5K_DCU_TXP_STATUS 0x00010000 /* Tx pause status (?) */ +#define AR5K_DCU_TXP_M 0x000003ff /* Tx pause mask */ +#define AR5K_DCU_TXP_STATUS 0x00010000 /* Tx pause status */ + +/* + * DCU transmit filter table 0 (32 entries) + */ +#define AR5K_DCU_TX_FILTER_0_BASE 0x1038 +#define AR5K_DCU_TX_FILTER_0(_n) (AR5K_DCU_TX_FILTER_0_BASE + (_n * 64)) /* - * DCU transmit filter register + * DCU transmit filter table 1 (16 entries) */ -#define AR5K_DCU_TX_FILTER 0x1038 +#define AR5K_DCU_TX_FILTER_1_BASE 0x103c +#define AR5K_DCU_TX_FILTER_1(_n) (AR5K_DCU_TX_FILTER_1_BASE + ((_n - 32) * 64)) /* * DCU clear transmit filter register @@ -739,9 +812,6 @@ /* * Reset control register - * - * 4 and 8 are not used in 5211/5212 and - * 2 means "baseband reset" on 5211/5212. */ #define AR5K_RESET_CTL 0x4000 /* Register Address */ #define AR5K_RESET_CTL_PCU 0x00000001 /* Protocol Control Unit reset */ @@ -765,6 +835,7 @@ #define AR5K_SLEEP_CTL_SLE_SLP 0x00010000 /* Force chip sleep */ #define AR5K_SLEEP_CTL_SLE_ALLOW 0x00020000 #define AR5K_SLEEP_CTL_SLE_UNITS 0x00000008 /* [5211+] */ +/* more bits */ /* * Interrupt pending register @@ -776,13 +847,14 @@ * Sleep force register */ #define AR5K_SFR 0x400c -#define AR5K_SFR_M 0x00000001 +#define AR5K_SFR_EN 0x00000001 /* * PCI configuration register */ #define AR5K_PCICFG 0x4010 /* Register Address */ #define AR5K_PCICFG_EEAE 0x00000001 /* Eeprom access enable [5210] */ +#define AR5K_PCICFG_SLEEP_CLOCK_EN 0x00000002 /* Enable sleep clock (?) */ #define AR5K_PCICFG_CLKRUNEN 0x00000004 /* CLKRUN enable [5211+] */ #define AR5K_PCICFG_EESIZE 0x00000018 /* Mask for EEPROM size [5211+] */ #define AR5K_PCICFG_EESIZE_S 3 @@ -798,19 +870,21 @@ #define AR5K_PCICFG_CBEFIX_DIS 0x00000400 /* Disable CBE fix (?) */ #define AR5K_PCICFG_SL_INTEN 0x00000800 /* Enable interrupts when asleep (?) */ #define AR5K_PCICFG_LED_BCTL 0x00001000 /* Led blink (?) [5210] */ -#define AR5K_PCICFG_SL_INPEN 0x00002800 /* Sleep even whith pending interrupts (?) */ +#define AR5K_PCICFG_UNK 0x00001000 /* Passed on some parts durring attach (?) */ +#define AR5K_PCICFG_SL_INPEN 0x00002000 /* Sleep even whith pending interrupts (?) */ #define AR5K_PCICFG_SPWR_DN 0x00010000 /* Mask for power status */ #define AR5K_PCICFG_LEDMODE 0x000e0000 /* Ledmode [5211+] */ #define AR5K_PCICFG_LEDMODE_PROP 0x00000000 /* Blink on standard traffic [5211+] */ #define AR5K_PCICFG_LEDMODE_PROM 0x00020000 /* Default mode (blink on any traffic) [5211+] */ #define AR5K_PCICFG_LEDMODE_PWR 0x00040000 /* Some other blinking mode (?) [5211+] */ #define AR5K_PCICFG_LEDMODE_RAND 0x00060000 /* Random blinking (?) [5211+] */ -#define AR5K_PCICFG_LEDBLINK 0x00700000 +#define AR5K_PCICFG_LEDBLINK 0x00700000 /* Led blink rate */ #define AR5K_PCICFG_LEDBLINK_S 20 -#define AR5K_PCICFG_LEDSLOW 0x00800000 /* Slow led blink rate (?) [5211+] */ +#define AR5K_PCICFG_LEDSLOW 0x00800000 /* Slowest led blink rate [5211+] */ #define AR5K_PCICFG_LEDSTATE \ (AR5K_PCICFG_LED | AR5K_PCICFG_LEDMODE | \ AR5K_PCICFG_LEDBLINK | AR5K_PCICFG_LEDSLOW) +#define AR5K_PCICFG_SLEEP_CLOCK_RATE 0x03000000 /* Sleep clock rate (field) */ /* * "General Purpose Input/Output" (GPIO) control register @@ -947,7 +1021,7 @@ #define AR5K_EEPROM_VERSION_4_4 0x4004 #define AR5K_EEPROM_VERSION_4_5 0x4005 #define AR5K_EEPROM_VERSION_4_6 0x4006 /* has ee_scaled_cck_delta */ -#define AR5K_EEPROM_VERSION_4_7 0x3007 +#define AR5K_EEPROM_VERSION_4_7 0x4007 #define AR5K_EEPROM_MODE_11A 0 #define AR5K_EEPROM_MODE_11B 1 @@ -1023,10 +1097,14 @@ #define AR5K_EEPROM_STAT_WRDONE 0x00000008 /* EEPROM write successful */ /* - * EEPROM config register (?) + * EEPROM config register */ -#define AR5K_EEPROM_CFG 0x6010 - +#define AR5K_EEPROM_CFG 0x6010 /* Register Addres */ +#define AR5K_EEPROM_CFG_SIZE_OVR 0x00000001 +#define AR5K_EEPROM_CFG_WR_WAIT_DIS 0x00000004 /* Disable write wait */ +#define AR5K_EEPROM_CFG_CLK_RATE 0x00000018 /* Clock rate */ +#define AR5K_EEPROM_CFG_PROT_KEY 0x00ffff00 /* Protectio key */ +#define AR5K_EEPROM_CFG_LIND_EN 0x01000000 /* Enable length indicator (?) */ /* @@ -1050,7 +1128,7 @@ #define AR5K_STA_ID1 0x8004 /* Register Address */ #define AR5K_STA_ID1_AP 0x00010000 /* Set AP mode */ #define AR5K_STA_ID1_ADHOC 0x00020000 /* Set Ad-Hoc mode */ -#define AR5K_STA_ID1_PWR_SV 0x00040000 /* Power save reporting (?) */ +#define AR5K_STA_ID1_PWR_SV 0x00040000 /* Power save reporting */ #define AR5K_STA_ID1_NO_KEYSRCH 0x00080000 /* No key search */ #define AR5K_STA_ID1_NO_PSPOLL 0x00100000 /* No power save polling [5210] */ #define AR5K_STA_ID1_PCF_5211 0x00100000 /* Enable PCF on [5211+] */ @@ -1059,9 +1137,13 @@ AR5K_STA_ID1_PCF_5210 : AR5K_STA_ID1_PCF_5211) #define AR5K_STA_ID1_DEFAULT_ANTENNA 0x00200000 /* Use default antenna */ #define AR5K_STA_ID1_DESC_ANTENNA 0x00400000 /* Update antenna from descriptor */ -#define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS (?) */ -#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS (?) */ +#define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS */ +#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS */ #define AR5K_STA_ID1_BASE_RATE_11B 0x02000000 /* Use 11b base rate (for ACK/CTS ?) [5211+] */ +#define AR5K_STA_ID1_SELF_GEN_SECTORE 0x04000000 /* Self generate sectore (?) */ +#define AR5K_STA_ID1_CRYPT_MIC_EN 0x08000000 /* Enable MIC */ +#define AR5K_STA_ID1_KEYSRCH_MODE 0x10000000 /* Keysearch mode (?) */ +#define AR5K_STA_ID1_PRESERVE_SEQ_NUM 0x20000000 /* Preserve sequence number */ /* * First BSSID register (MAC address, lower 32bits) @@ -1117,7 +1199,7 @@ * * Retry limit register for 5210 (no QCU/DCU so it's done in PCU) */ -#define AR5K_NODCU_RETRY_LMT 0x801c /*Register Address */ +#define AR5K_NODCU_RETRY_LMT 0x801c /* Register Address */ #define AR5K_NODCU_RETRY_LMT_SH_RETRY 0x0000000f /* Short retry limit mask */ #define AR5K_NODCU_RETRY_LMT_SH_RETRY_S 0 #define AR5K_NODCU_RETRY_LMT_LG_RETRY 0x000000f0 /* Long retry mask */ @@ -1136,9 +1218,9 @@ #define AR5K_USEC_5211 0x801c /* Register Address [5211+] */ #define AR5K_USEC (ah->ah_version == AR5K_AR5210 ? \ AR5K_USEC_5210 : AR5K_USEC_5211) -#define AR5K_USEC_1 0x0000007f +#define AR5K_USEC_1 0x0000007f /* clock cycles for 1us */ #define AR5K_USEC_1_S 0 -#define AR5K_USEC_32 0x00003f80 +#define AR5K_USEC_32 0x00003f80 /* clock cycles for 1us while on 32Mhz clock */ #define AR5K_USEC_32_S 7 #define AR5K_USEC_TX_LATENCY_5211 0x007fc000 #define AR5K_USEC_TX_LATENCY_5211_S 14 @@ -1152,16 +1234,16 @@ /* * PCU beacon control register */ -#define AR5K_BEACON_5210 0x8024 -#define AR5K_BEACON_5211 0x8020 +#define AR5K_BEACON_5210 0x8024 /*Register Address [5210] */ +#define AR5K_BEACON_5211 0x8020 /*Register Address [5211+] */ #define AR5K_BEACON (ah->ah_version == AR5K_AR5210 ? \ AR5K_BEACON_5210 : AR5K_BEACON_5211) -#define AR5K_BEACON_PERIOD 0x0000ffff +#define AR5K_BEACON_PERIOD 0x0000ffff /* Mask for beacon period */ #define AR5K_BEACON_PERIOD_S 0 -#define AR5K_BEACON_TIM 0x007f0000 +#define AR5K_BEACON_TIM 0x007f0000 /* Mask for TIM offset */ #define AR5K_BEACON_TIM_S 16 -#define AR5K_BEACON_ENABLE 0x00800000 -#define AR5K_BEACON_RESET_TSF 0x01000000 +#define AR5K_BEACON_ENABLE 0x00800000 /* Enable beacons */ +#define AR5K_BEACON_RESET_TSF 0x01000000 /* Force TSF reset */ /* * CFP period register @@ -1234,7 +1316,6 @@ /* * Receive filter register - * TODO: Get these out of ar5xxx.h on ath5k */ #define AR5K_RX_FILTER_5210 0x804c /* Register Address [5210] */ #define AR5K_RX_FILTER_5211 0x803c /* Register Address [5211+] */ @@ -1307,11 +1388,11 @@ #define AR5K_DIAG_SW_5211 0x8048 /* Register Address [5211+] */ #define AR5K_DIAG_SW (ah->ah_version == AR5K_AR5210 ? \ AR5K_DIAG_SW_5210 : AR5K_DIAG_SW_5211) -#define AR5K_DIAG_SW_DIS_WEP_ACK 0x00000001 -#define AR5K_DIAG_SW_DIS_ACK 0x00000002 /* Disable ACKs (?) */ -#define AR5K_DIAG_SW_DIS_CTS 0x00000004 /* Disable CTSs (?) */ -#define AR5K_DIAG_SW_DIS_ENC 0x00000008 /* Disable encryption (?) */ -#define AR5K_DIAG_SW_DIS_DEC 0x00000010 /* Disable decryption (?) */ +#define AR5K_DIAG_SW_DIS_WEP_ACK 0x00000001 /* Disable ACKs if WEP key is invalid */ +#define AR5K_DIAG_SW_DIS_ACK 0x00000002 /* Disable ACKs */ +#define AR5K_DIAG_SW_DIS_CTS 0x00000004 /* Disable CTSs */ +#define AR5K_DIAG_SW_DIS_ENC 0x00000008 /* Disable encryption */ +#define AR5K_DIAG_SW_DIS_DEC 0x00000010 /* Disable decryption */ #define AR5K_DIAG_SW_DIS_TX 0x00000020 /* Disable transmit [5210] */ #define AR5K_DIAG_SW_DIS_RX_5210 0x00000040 /* Disable recieve */ #define AR5K_DIAG_SW_DIS_RX_5211 0x00000020 @@ -1329,13 +1410,13 @@ #define AR5K_DIAG_SW_CHAN_INFO_5211 0x00000100 #define AR5K_DIAG_SW_CHAN_INFO (ah->ah_version == AR5K_AR5210 ? \ AR5K_DIAG_SW_CHAN_INFO_5210 : AR5K_DIAG_SW_CHAN_INFO_5211) -#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211 0x00000200 /* Scrambler seed (?) */ +#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211 0x00000200 /* Enable scrambler seed */ #define AR5K_DIAG_SW_EN_SCRAM_SEED_5210 0x00000400 #define AR5K_DIAG_SW_EN_SCRAM_SEED (ah->ah_version == AR5K_AR5210 ? \ AR5K_DIAG_SW_EN_SCRAM_SEED_5210 : AR5K_DIAG_SW_EN_SCRAM_SEED_5211) #define AR5K_DIAG_SW_ECO_ENABLE 0x00000400 /* [5211+] */ #define AR5K_DIAG_SW_SCVRAM_SEED 0x0003f800 /* [5210] */ -#define AR5K_DIAG_SW_SCRAM_SEED_M 0x0001fc00 /* Scrambler seed mask (?) */ +#define AR5K_DIAG_SW_SCRAM_SEED_M 0x0001fc00 /* Scrambler seed mask */ #define AR5K_DIAG_SW_SCRAM_SEED_S 10 #define AR5K_DIAG_SW_DIS_SEQ_INC 0x00040000 /* Disable seqnum increment (?)[5210] */ #define AR5K_DIAG_SW_FRAME_NV0_5210 0x00080000 @@ -1344,6 +1425,7 @@ AR5K_DIAG_SW_FRAME_NV0_5210 : AR5K_DIAG_SW_FRAME_NV0_5211) #define AR5K_DIAG_SW_OBSPT_M 0x000c0000 #define AR5K_DIAG_SW_OBSPT_S 18 +/* more bits */ /* * TSF (clock) register (lower 32 bits) @@ -1369,15 +1451,34 @@ /* * ADDAC test register [5211+] */ -#define AR5K_ADDAC_TEST 0x8054 -#define AR5K_ADDAC_TEST_TXCONT 0x00000001 +#define AR5K_ADDAC_TEST 0x8054 /* Register Address */ +#define AR5K_ADDAC_TEST_TXCONT 0x00000001 /* Test continuous tx */ +#define AR5K_ADDAC_TEST_TST_MODE 0x00000002 /* Test mode */ +#define AR5K_ADDAC_TEST_LOOP_EN 0x00000004 /* Enable loop */ +#define AR5K_ADDAC_TEST_LOOP_LEN 0x00000008 /* Loop length (field) */ +#define AR5K_ADDAC_TEST_USE_U8 0x00004000 /* Use upper 8 bits */ +#define AR5K_ADDAC_TEST_MSB 0x00008000 /* State of MSB */ +#define AR5K_ADDAC_TEST_TRIG_SEL 0x00010000 /* Trigger select */ +#define AR5K_ADDAC_TEST_TRIG_PTY 0x00020000 /* Trigger polarity */ +#define AR5K_ADDAC_TEST_RXCONT 0x00040000 /* Continuous capture */ +#define AR5K_ADDAC_TEST_CAPTURE 0x00080000 /* Begin capture */ +#define AR5K_ADDAC_TEST_TST_ARM 0x00100000 /* Test ARM (Adaptive Radio Mode ?) */ /* * Default antenna register [5211+] */ #define AR5K_DEFAULT_ANTENNA 0x8058 +/* + * Frame control QoS mask register (?) [5211+] + * (FC_QOS_MASK) + */ +#define AR5K_FRAME_CTL_QOSM 0x805c +/* + * Seq mask register (?) [5211+] + */ +#define AR5K_SEQ_MASK 0x8060 /* * Retry count register [5210] @@ -1449,124 +1550,242 @@ /* * XR (eXtended Range) mode register */ -#define AR5K_XRMODE 0x80c0 -#define AR5K_XRMODE_POLL_TYPE_M 0x0000003f +#define AR5K_XRMODE 0x80c0 /* Register Address */ +#define AR5K_XRMODE_POLL_TYPE_M 0x0000003f /* Mask for Poll type (?) */ #define AR5K_XRMODE_POLL_TYPE_S 0 -#define AR5K_XRMODE_POLL_SUBTYPE_M 0x0000003c +#define AR5K_XRMODE_POLL_SUBTYPE_M 0x0000003c /* Mask for Poll subtype (?) */ #define AR5K_XRMODE_POLL_SUBTYPE_S 2 -#define AR5K_XRMODE_POLL_WAIT_ALL 0x00000080 -#define AR5K_XRMODE_SIFS_DELAY 0x000fff00 -#define AR5K_XRMODE_FRAME_HOLD_M 0xfff00000 +#define AR5K_XRMODE_POLL_WAIT_ALL 0x00000080 /* Wait for poll */ +#define AR5K_XRMODE_SIFS_DELAY 0x000fff00 /* Mask for SIFS delay */ +#define AR5K_XRMODE_FRAME_HOLD_M 0xfff00000 /* Mask for frame hold (?) */ #define AR5K_XRMODE_FRAME_HOLD_S 20 /* * XR delay register */ -#define AR5K_XRDELAY 0x80c4 -#define AR5K_XRDELAY_SLOT_DELAY_M 0x0000ffff +#define AR5K_XRDELAY 0x80c4 /* Register Address */ +#define AR5K_XRDELAY_SLOT_DELAY_M 0x0000ffff /* Mask for slot delay */ #define AR5K_XRDELAY_SLOT_DELAY_S 0 -#define AR5K_XRDELAY_CHIRP_DELAY_M 0xffff0000 +#define AR5K_XRDELAY_CHIRP_DELAY_M 0xffff0000 /* Mask for CHIRP data delay */ #define AR5K_XRDELAY_CHIRP_DELAY_S 16 /* * XR timeout register */ -#define AR5K_XRTIMEOUT 0x80c8 -#define AR5K_XRTIMEOUT_CHIRP_M 0x0000ffff +#define AR5K_XRTIMEOUT 0x80c8 /* Register Address */ +#define AR5K_XRTIMEOUT_CHIRP_M 0x0000ffff /* Mask for CHIRP timeout */ #define AR5K_XRTIMEOUT_CHIRP_S 0 -#define AR5K_XRTIMEOUT_POLL_M 0xffff0000 +#define AR5K_XRTIMEOUT_POLL_M 0xffff0000 /* Mask for Poll timeout */ #define AR5K_XRTIMEOUT_POLL_S 16 /* * XR chirp register */ -#define AR5K_XRCHIRP 0x80cc -#define AR5K_XRCHIRP_SEND 0x00000001 -#define AR5K_XRCHIRP_GAP 0xffff0000 +#define AR5K_XRCHIRP 0x80cc /* Register Address */ +#define AR5K_XRCHIRP_SEND 0x00000001 /* Send CHIRP */ +#define AR5K_XRCHIRP_GAP 0xffff0000 /* Mask for CHIRP gap (?) */ /* * XR stomp register */ -#define AR5K_XRSTOMP 0x80d0 -#define AR5K_XRSTOMP_TX 0x00000001 -#define AR5K_XRSTOMP_RX_ABORT 0x00000002 -#define AR5K_XRSTOMP_RSSI_THRES 0x0000ff00 +#define AR5K_XRSTOMP 0x80d0 /* Register Address */ +#define AR5K_XRSTOMP_TX 0x00000001 /* Stomp Tx (?) */ +#define AR5K_XRSTOMP_RX 0x00000002 /* Stomp Rx (?) */ +#define AR5K_XRSTOMP_TX_RSSI 0x00000004 /* Stomp Tx RSSI (?) */ +#define AR5K_XRSTOMP_TX_BSSID 0x00000008 /* Stomp Tx BSSID (?) */ +#define AR5K_XRSTOMP_DATA 0x00000010 /* Stomp data (?)*/ +#define AR5K_XRSTOMP_RSSI_THRES 0x0000ff00 /* Mask for XR RSSI threshold */ /* * First enhanced sleep register */ -#define AR5K_SLEEP0 0x80d4 -#define AR5K_SLEEP0_NEXT_DTIM 0x0007ffff +#define AR5K_SLEEP0 0x80d4 /* Register Address */ +#define AR5K_SLEEP0_NEXT_DTIM 0x0007ffff /* Mask for next DTIM (?) */ #define AR5K_SLEEP0_NEXT_DTIM_S 0 -#define AR5K_SLEEP0_ASSUME_DTIM 0x00080000 -#define AR5K_SLEEP0_ENH_SLEEP_EN 0x00100000 -#define AR5K_SLEEP0_CABTO 0xff000000 +#define AR5K_SLEEP0_ASSUME_DTIM 0x00080000 /* Assume DTIM */ +#define AR5K_SLEEP0_ENH_SLEEP_EN 0x00100000 /* Enable enchanced sleep control */ +#define AR5K_SLEEP0_CABTO 0xff000000 /* Mask for CAB Time Out */ #define AR5K_SLEEP0_CABTO_S 24 /* * Second enhanced sleep register */ -#define AR5K_SLEEP1 0x80d8 -#define AR5K_SLEEP1_NEXT_TIM 0x0007ffff +#define AR5K_SLEEP1 0x80d8 /* Register Address */ +#define AR5K_SLEEP1_NEXT_TIM 0x0007ffff /* Mask for next TIM (?) */ #define AR5K_SLEEP1_NEXT_TIM_S 0 -#define AR5K_SLEEP1_BEACON_TO 0xff000000 +#define AR5K_SLEEP1_BEACON_TO 0xff000000 /* Mask for Beacon Time Out */ #define AR5K_SLEEP1_BEACON_TO_S 24 /* * Third enhanced sleep register */ -#define AR5K_SLEEP2 0x80dc -#define AR5K_SLEEP2_TIM_PER 0x0000ffff +#define AR5K_SLEEP2 0x80dc /* Register Address */ +#define AR5K_SLEEP2_TIM_PER 0x0000ffff /* Mask for TIM period (?) */ #define AR5K_SLEEP2_TIM_PER_S 0 -#define AR5K_SLEEP2_DTIM_PER 0xffff0000 +#define AR5K_SLEEP2_DTIM_PER 0xffff0000 /* Mask for DTIM period (?) */ #define AR5K_SLEEP2_DTIM_PER_S 16 /* * BSSID mask registers */ -#define AR5K_BSS_IDM0 0x80e0 -#define AR5K_BSS_IDM1 0x80e4 +#define AR5K_BSS_IDM0 0x80e0 /* Upper bits */ +#define AR5K_BSS_IDM1 0x80e4 /* Lower bits */ /* * TX power control (TPC) register + * + * XXX: PCDAC steps (0.5dbm) or DBM ? + * + * XXX: Mask changes for newer chips to 7f + * like tx power table ? */ -#define AR5K_TXPC 0x80e8 -#define AR5K_TXPC_ACK_M 0x0000003f +#define AR5K_TXPC 0x80e8 /* Register Address */ +#define AR5K_TXPC_ACK_M 0x0000003f /* Mask for ACK tx power */ #define AR5K_TXPC_ACK_S 0 -#define AR5K_TXPC_CTS_M 0x00003f00 +#define AR5K_TXPC_CTS_M 0x00003f00 /* Mask for CTS tx power */ #define AR5K_TXPC_CTS_S 8 -#define AR5K_TXPC_CHIRP_M 0x003f0000 +#define AR5K_TXPC_CHIRP_M 0x003f0000 /* Mask for CHIRP tx power */ #define AR5K_TXPC_CHIRP_S 22 /* * Profile count registers */ -#define AR5K_PROFCNT_TX 0x80ec -#define AR5K_PROFCNT_RX 0x80f0 -#define AR5K_PROFCNT_RXCLR 0x80f4 -#define AR5K_PROFCNT_CYCLE 0x80f8 +#define AR5K_PROFCNT_TX 0x80ec /* Tx count */ +#define AR5K_PROFCNT_RX 0x80f0 /* Rx count */ +#define AR5K_PROFCNT_RXCLR 0x80f4 /* Clear Rx count */ +#define AR5K_PROFCNT_CYCLE 0x80f8 /* Cycle count (?) */ + +/* + * Quiet (period) control registers (?) + */ +#define AR5K_QUIET_CTL1 0x80fc /* Register Address */ +#define AR5K_QUIET_CTL1_NEXT_QT 0x0000ffff /* Mask for next quiet (period?) (?) */ +#define AR5K_QUIET_CTL1_QT_EN 0x00010000 /* Enable quiet (period?) */ +#define AR5K_QUIET_CTL2 0x8100 /* Register Address */ +#define AR5K_QUIET_CTL2_QT_PER 0x0000ffff /* Mask for quiet period (?) */ +#define AR5K_QUIET_CTL2_QT_DUR 0xffff0000 /* Mask for quiet duration (?) */ /* * TSF parameter register */ -#define AR5K_TSF_PARM 0x8104 -#define AR5K_TSF_PARM_INC_M 0x000000ff +#define AR5K_TSF_PARM 0x8104 /* Register Address */ +#define AR5K_TSF_PARM_INC_M 0x000000ff /* Mask for TSF increment */ #define AR5K_TSF_PARM_INC_S 0 /* + * QoS register (?) + */ +#define AR5K_QOS 0x8108 /* Register Address */ +#define AR5K_QOS_NOACK_2BIT_VALUES 0x00000000 /* (field) */ +#define AR5K_QOS_NOACK_BIT_OFFSET 0x00000020 /* (field) */ +#define AR5K_QOS_NOACK_BYTE_OFFSET 0x00000080 /* (field) */ + +/* * PHY error filter register */ #define AR5K_PHY_ERR_FIL 0x810c -#define AR5K_PHY_ERR_FIL_RADAR 0x00000020 -#define AR5K_PHY_ERR_FIL_OFDM 0x00020000 -#define AR5K_PHY_ERR_FIL_CCK 0x02000000 +#define AR5K_PHY_ERR_FIL_RADAR 0x00000020 /* Radar signal */ +#define AR5K_PHY_ERR_FIL_OFDM 0x00020000 /* OFDM false detect (ANI) */ +#define AR5K_PHY_ERR_FIL_CCK 0x02000000 /* CCK false detect (ANI) */ + +/* + * XR latency register + */ +#define AR5K_XRLAT_TX 0x8110 /* - * Rate duration register + * ACK SIFS register + */ +#define AR5K_ACKSIFS 0x8114 /* Register Address */ +#define AR5K_ACKSIFS_INC 0x00000000 /* ACK SIFS Increment (field) */ + +/* + * MIC QoS control register (?) + */ +#define AR5K_MIC_QOS_CTL 0x8118 /* Register Address */ +#define AR5K_MIC_QOS_CTL_0 0x00000001 /* MIC QoS control 0 (?) */ +#define AR5K_MIC_QOS_CTL_1 0x00000004 /* MIC QoS control 1 (?) */ +#define AR5K_MIC_QOS_CTL_2 0x00000010 /* MIC QoS control 2 (?) */ +#define AR5K_MIC_QOS_CTL_3 0x00000040 /* MIC QoS control 3 (?) */ +#define AR5K_MIC_QOS_CTL_4 0x00000100 /* MIC QoS control 4 (?) */ +#define AR5K_MIC_QOS_CTL_5 0x00000400 /* MIC QoS control 5 (?) */ +#define AR5K_MIC_QOS_CTL_6 0x00001000 /* MIC QoS control 6 (?) */ +#define AR5K_MIC_QOS_CTL_7 0x00004000 /* MIC QoS control 7 (?) */ +#define AR5K_MIC_QOS_CTL_MQ_EN 0x00010000 /* Enable MIC QoS */ + +/* + * MIC QoS select register (?) + */ +#define AR5K_MIC_QOS_SEL 0x811c +#define AR5K_MIC_QOS_SEL_0 0x00000001 +#define AR5K_MIC_QOS_SEL_1 0x00000010 +#define AR5K_MIC_QOS_SEL_2 0x00000100 +#define AR5K_MIC_QOS_SEL_3 0x00001000 +#define AR5K_MIC_QOS_SEL_4 0x00010000 +#define AR5K_MIC_QOS_SEL_5 0x00100000 +#define AR5K_MIC_QOS_SEL_6 0x01000000 +#define AR5K_MIC_QOS_SEL_7 0x10000000 + +/* + * Misc mode control register (?) + */ +#define AR5K_MISC_MODE 0x8120 /* Register Address */ +#define AR5K_MISC_MODE_FBSSID_MATCH 0x00000001 /* Force BSSID match */ +#define AR5K_MISC_MODE_ACKSIFS_MEM 0x00000002 /* ACK SIFS memory (?) */ +/* more bits */ + +/* + * OFDM Filter counter + */ +#define AR5K_OFDM_FIL_CNT 0x8124 + +/* + * CCK Filter counter + */ +#define AR5K_CCK_FIL_CNT 0x8128 + +/* + * PHY Error Counters (?) + */ +#define AR5K_PHYERR_CNT1 0x812c +#define AR5K_PHYERR_CNT1_MASK 0x8130 + +#define AR5K_PHYERR_CNT2 0x8134 +#define AR5K_PHYERR_CNT2_MASK 0x8138 + +/* + * TSF Threshold register (?) + */ +#define AR5K_TSF_THRES 0x813c + +/* + * Rate -> ACK SIFS mapping table (32 entries) + */ +#define AR5K_RATE_ACKSIFS_BASE 0x8680 /* Register Address */ +#define AR5K_RATE_ACKSIFS(_n) (AR5K_RATE_ACKSIFS_BSE + ((_n) << 2)) +#define AR5K_RATE_ACKSIFS_NORMAL 0x00000001 /* Normal SIFS (field) */ +#define AR5K_RATE_ACKSIFS_TURBO 0x00000400 /* Turbo SIFS (field) */ + +/* + * Rate -> duration mapping table (32 entries) */ #define AR5K_RATE_DUR_BASE 0x8700 #define AR5K_RATE_DUR(_n) (AR5K_RATE_DUR_BASE + ((_n) << 2)) +/* + * Rate -> db mapping table + * (8 entries, each one has 4 8bit fields) + */ +#define AR5K_RATE2DB_BASE 0x87c0 +#define AR5K_RATE2DB(_n) (AR5K_RATE2DB_BASE + ((_n) << 2)) + +/* + * db -> Rate mapping table + * (8 entries, each one has 4 8bit fields) + */ +#define AR5K_DB2RATE_BASE 0x87e0 +#define AR5K_DB2RATE(_n) (AR5K_DB2RATE_BASE + ((_n) << 2)) + /*===5212 end===*/ /* @@ -1613,12 +1832,34 @@ /*===PHY REGISTERS===*/ /* - * PHY register + * PHY registers start */ #define AR5K_PHY_BASE 0x9800 #define AR5K_PHY(_n) (AR5K_PHY_BASE + ((_n) << 2)) -#define AR5K_PHY_SHIFT_2GHZ 0x00004007 -#define AR5K_PHY_SHIFT_5GHZ 0x00000007 + +/* + * TST_2 (Misc config parameters) + */ +#define AR5K_PHY_TST2 0x9800 /* Register Address */ +#define AR5K_PHY_TST2_TRIG_SEL 0x00000001 /* Trigger select (?) (field ?) */ +#define AR5K_PHY_TST2_TRIG 0x00000010 /* Trigger (?) (field ?) */ +#define AR5K_PHY_TST2_CBUS_MODE 0x00000100 /* Cardbus mode (?) */ +/* bit reserved */ +#define AR5K_PHY_TST2_CLK32 0x00000400 /* CLK_OUT is CLK32 (32Khz external) */ +#define AR5K_PHY_TST2_CHANCOR_DUMP_EN 0x00000800 /* Enable Chancor dump (?) */ +#define AR5K_PHY_TST2_EVEN_CHANCOR_DUMP 0x00001000 /* Even Chancor dump (?) */ +#define AR5K_PHY_TST2_RFSILENT_EN 0x00002000 /* Enable RFSILENT */ +#define AR5K_PHY_TST2_ALT_RFDATA 0x00004000 /* Alternate RFDATA (5-2GHz switch) */ +#define AR5K_PHY_TST2_MINI_OBS_EN 0x00008000 /* Enable mini OBS (?) */ +#define AR5K_PHY_TST2_RX2_IS_RX5_INV 0x00010000 /* 2GHz rx path is the 5GHz path inverted (?) */ +#define AR5K_PHY_TST2_SLOW_CLK160 0x00020000 /* Slow CLK160 (?) */ +#define AR5K_PHY_TST2_AGC_OBS_SEL_3 0x00040000 /* AGC OBS Select 3 (?) */ +#define AR5K_PHY_TST2_BBB_OBS_SEL 0x00080000 /* BB OBS Select (field ?) */ +#define AR5K_PHY_TST2_ADC_OBS_SEL 0x00800000 /* ADC OBS Select (field ?) */ +#define AR5K_PHY_TST2_RX_CLR_SEL 0x08000000 /* RX Clear Select (?) */ +#define AR5K_PHY_TST2_FORCE_AGC_CLR 0x10000000 /* Force AGC clear (?) */ +#define AR5K_PHY_SHIFT_2GHZ 0x00004007 /* Used to access 2GHz radios */ +#define AR5K_PHY_SHIFT_5GHZ 0x00000007 /* Used to access 5GHz radios (default) */ /* * PHY frame control register [5110] /turbo mode register [5111+] @@ -1630,18 +1871,21 @@ * a "turbo mode register" for 5110. We treat this one as * a frame control register for 5110 below. */ -#define AR5K_PHY_TURBO 0x9804 -#define AR5K_PHY_TURBO_MODE 0x00000001 -#define AR5K_PHY_TURBO_SHORT 0x00000002 +#define AR5K_PHY_TURBO 0x9804 /* Register Address */ +#define AR5K_PHY_TURBO_MODE 0x00000001 /* Enable turbo mode */ +#define AR5K_PHY_TURBO_SHORT 0x00000002 /* Short mode (20Mhz channels) (?) */ /* * PHY agility command register + * (aka TST_1) */ -#define AR5K_PHY_AGC 0x9808 -#define AR5K_PHY_AGC_DISABLE 0x08000000 +#define AR5K_PHY_AGC 0x9808 /* Register Address */ +#define AR5K_PHY_TST1 0x9808 +#define AR5K_PHY_AGC_DISABLE 0x08000000 /* Disable AGC to A2 (?)*/ +#define AR5K_PHY_TST1_TXHOLD 0x00003800 /* Set tx hold (?) */ /* - * PHY timing register [5112+] + * PHY timing register 3 [5112+] */ #define AR5K_PHY_TIMING_3 0x9814 #define AR5K_PHY_TIMING_3_DSC_MAN 0xfffe0000 @@ -1657,26 +1901,81 @@ /* * PHY activation register */ -#define AR5K_PHY_ACT 0x981c -#define AR5K_PHY_ACT_ENABLE 0x00000001 -#define AR5K_PHY_ACT_DISABLE 0x00000002 +#define AR5K_PHY_ACT 0x981c /* Register Address */ +#define AR5K_PHY_ACT_ENABLE 0x00000001 /* Activate PHY */ +#define AR5K_PHY_ACT_DISABLE 0x00000002 /* Deactivate PHY */ + +/* + * PHY RF control registers + * (i think these are delay times, + * these calibration values exist + * in EEPROM) + */ +#define AR5K_PHY_RF_CTL2 0x9824 /* Register Address */ +#define AR5K_PHY_RF_CTL2_TXF2TXD_START 0x0000000f /* Mask for TX frame to TX d(esc?) start */ + +#define AR5K_PHY_RF_CTL3 0x9828 /* Register Address */ +#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON 0x0000000f /* Mask for TX end to XLNA on */ + +#define AR5K_PHY_RF_CTL4 0x9834 /* Register Address */ +#define AR5K_PHY_RF_CTL4_TXF2XPA_A_ON 0x00000001 /* TX frame to XPA A on (field) */ +#define AR5K_PHY_RF_CTL4_TXF2XPA_B_ON 0x00000100 /* TX frame to XPA B on (field) */ +#define AR5K_PHY_RF_CTL4_TXE2XPA_A_OFF 0x00010000 /* TX end to XPA A off (field) */ +#define AR5K_PHY_RF_CTL4_TXE2XPA_B_OFF 0x01000000 /* TX end to XPA B off (field) */ + +/* + * Pre-Amplifier control register + * (XPA -> external pre-amplifier) + */ +#define AR5K_PHY_PA_CTL 0x9838 /* Register Address */ +#define AR5K_PHY_PA_CTL_XPA_A_HI 0x00000001 /* XPA A high (?) */ +#define AR5K_PHY_PA_CTL_XPA_B_HI 0x00000002 /* XPA B high (?) */ +#define AR5K_PHY_PA_CTL_XPA_A_EN 0x00000004 /* Enable XPA A */ +#define AR5K_PHY_PA_CTL_XPA_B_EN 0x00000008 /* Enable XPA B */ + +/* + * PHY settling register + */ +#define AR5K_PHY_SETTLING 0x9844 /* Register Address */ +#define AR5K_PHY_SETTLING_AGC 0x0000007f /* Mask for AGC settling time */ +#define AR5K_PHY_SETTLING_SWITCH 0x00003f80 /* Mask for Switch settlig time */ + +/* + * PHY Gain registers + */ +#define AR5K_PHY_GAIN 0x9848 /* Register Address */ +#define AR5K_PHY_GAIN_TXRX_ATTEN 0x0003f000 /* Mask for TX-RX Attenuation */ + +#define AR5K_PHY_GAIN_OFFSET 0x984c /* Register Address */ +#define AR5K_PHY_GAIN_OFFSET_RXTX_FLAG 0x00020000 /* RX-TX flag (?) */ + +/* + * Desired size register + * (for more infos read ANI patent) + */ +#define AR5K_PHY_DESIRED_SIZE 0x9850 /* Register Address */ +#define AR5K_PHY_DESIRED_SIZE_ADC 0x000000ff /* Mask for ADC desired size */ +#define AR5K_PHY_DESIRED_SIZE_PGA 0x0000ff00 /* Mask for PGA desired size */ +#define AR5K_PHY_DESIRED_SIZE_TOT 0x0ff00000 /* Mask for Total desired size (?) */ /* * PHY signal register + * (for more infos read ANI patent) */ -#define AR5K_PHY_SIG 0x9858 -#define AR5K_PHY_SIG_FIRSTEP 0x0003f000 +#define AR5K_PHY_SIG 0x9858 /* Register Address */ +#define AR5K_PHY_SIG_FIRSTEP 0x0003f000 /* Mask for FIRSTEP */ #define AR5K_PHY_SIG_FIRSTEP_S 12 -#define AR5K_PHY_SIG_FIRPWR 0x03fc0000 +#define AR5K_PHY_SIG_FIRPWR 0x03fc0000 /* Mask for FIPWR */ #define AR5K_PHY_SIG_FIRPWR_S 18 /* * PHY coarse agility control register + * (for more infos read ANI patent) */ -#define AR5K_PHY_AGCCOARSE 0x985c -#define AR5K_PHY_AGCCOARSE_LO 0x00007f80 +#define AR5K_PHY_AGCCOARSE 0x985c /* Register Address */ +#define AR5K_PHY_AGCCOARSE_LO 0x00007f80 /* Mask for AGC Coarse low */ #define AR5K_PHY_AGCCOARSE_LO_S 7 -#define AR5K_PHY_AGCCOARSE_HI 0x003f8000 +#define AR5K_PHY_AGCCOARSE_HI 0x003f8000 /* Mask for AGC Coarse high */ #define AR5K_PHY_AGCCOARSE_HI_S 15 /* @@ -1689,12 +1988,13 @@ /* * PHY noise floor status register */ -#define AR5K_PHY_NF 0x9864 -#define AR5K_PHY_NF_M 0x000001ff -#define AR5K_PHY_NF_ACTIVE 0x00000100 +#define AR5K_PHY_NF 0x9864 /* Register address */ +#define AR5K_PHY_NF_M 0x000001ff /* Noise floor mask */ +#define AR5K_PHY_NF_ACTIVE 0x00000100 /* Noise floor calibration still active */ #define AR5K_PHY_NF_RVAL(_n) (((_n) >> 19) & AR5K_PHY_NF_M) #define AR5K_PHY_NF_AVAL(_n) (-((_n) ^ AR5K_PHY_NF_M) + 1) #define AR5K_PHY_NF_SVAL(_n) (((_n) & AR5K_PHY_NF_M) | (1 << 9)) +#define AR5K_PHY_NF_THRESH62 0x00001000 /* Thresh62 -check ANI patent- (field) */ /* * PHY ADC saturation register [5110] @@ -1706,6 +2006,30 @@ #define AR5K_PHY_ADCSAT_THR_S 5 /* + * PHY Weak ofdm signal detection threshold registers (ANI) [5212+] + */ + +/* High thresholds */ +#define AR5K_PHY_WEAK_OFDM_HIGH_THR 0x9868 +#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT 0x0000001f +#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT_S 0 +#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1 0x00fe0000 +#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1_S 17 +#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2 0x7f000000 +#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_S 24 + +/* Low thresholds */ +#define AR5K_PHY_WEAK_OFDM_LOW_THR 0x986c +#define AR5K_PHY_WEAK_OFDM_LOW_THR_SELFCOR_EN 0x00000001 +#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT 0x00003f00 +#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT_S 8 +#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1 0x001fc000 +#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1_S 14 +#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2 0x0fe00000 +#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_S 21 + + +/* * PHY sleep registers [5112+] */ #define AR5K_PHY_SCR 0x9870 @@ -1730,6 +2054,8 @@ AR5K_PHY_PLL_44MHZ_5211 : AR5K_PHY_PLL_44MHZ_5212) #define AR5K_PHY_PLL_RF5111 0x00000000 #define AR5K_PHY_PLL_RF5112 0x00000040 +#define AR5K_PHY_PLL_HALF_RATE 0x00000100 +#define AR5K_PHY_PLL_QUARTER_RATE 0x00000200 /* * RF Buffer register @@ -1792,23 +2118,74 @@ #define AR5K_PHY_RFSTG_DISABLE 0x00000021 /* + * PHY Antenna control register + */ +#define AR5K_PHY_ANT_CTL 0x9910 /* Register Address */ +#define AR5K_PHY_ANT_CTL_TXRX_EN 0x00000001 /* Enable TX/RX (?) */ +#define AR5K_PHY_ANT_CTL_SECTORED_ANT 0x00000004 /* Sectored Antenna */ +#define AR5K_PHY_ANT_CTL_HITUNE5 0x00000008 /* Hitune5 (?) */ +#define AR5K_PHY_ANT_CTL_SWTABLE_IDLE 0x00000010 /* Switch table idle (?) */ + +/* * PHY receiver delay register [5111+] */ -#define AR5K_PHY_RX_DELAY 0x9914 -#define AR5K_PHY_RX_DELAY_M 0x00003fff +#define AR5K_PHY_RX_DELAY 0x9914 /* Register Address */ +#define AR5K_PHY_RX_DELAY_M 0x00003fff /* Mask for RX activate to receive delay (/100ns) */ + +/* + * PHY max rx length register (?) [5111] + */ +#define AR5K_PHY_MAX_RX_LEN 0x991c /* - * PHY timing I(nphase) Q(adrature) control register [5111+] + * PHY timing register 4 + * I(nphase)/Q(adrature) calibration register [5111+] */ -#define AR5K_PHY_IQ 0x9920 /* Register address */ +#define AR5K_PHY_IQ 0x9920 /* Register Address */ #define AR5K_PHY_IQ_CORR_Q_Q_COFF 0x0000001f /* Mask for q correction info */ #define AR5K_PHY_IQ_CORR_Q_I_COFF 0x000007e0 /* Mask for i correction info */ #define AR5K_PHY_IQ_CORR_Q_I_COFF_S 5 #define AR5K_PHY_IQ_CORR_ENABLE 0x00000800 /* Enable i/q correction */ -#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX 0x0000f000 +#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX 0x0000f000 /* Mask for max number of samples in log scale */ #define AR5K_PHY_IQ_CAL_NUM_LOG_MAX_S 12 #define AR5K_PHY_IQ_RUN 0x00010000 /* Run i/q calibration */ +#define AR5K_PHY_IQ_USE_PT_DF 0x00020000 /* Use pilot track df (?) */ +#define AR5K_PHY_IQ_EARLY_TRIG_THR 0x00200000 /* Early trigger threshold (?) (field) */ +#define AR5K_PHY_IQ_PILOT_MASK_EN 0x10000000 /* Enable pilot mask (?) */ +#define AR5K_PHY_IQ_CHAN_MASK_EN 0x20000000 /* Enable channel mask (?) */ +#define AR5K_PHY_IQ_SPUR_FILT_EN 0x40000000 /* Enable spur filter */ +#define AR5K_PHY_IQ_SPUR_RSSI_EN 0x80000000 /* Enable spur rssi */ +/* + * PHY timing register 5 + * OFDM Self-correlator Cyclic RSSI threshold params + * (Check out bb_cycpwr_thr1 on ANI patent) + */ +#define AR5K_PHY_OFDM_SELFCORR 0x9924 /* Register Address */ +#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_EN 0x00000001 /* Enable cyclic RSSI thr 1 */ +#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1 0x000000fe /* Mask for Cyclic RSSI threshold 1 */ +#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR3 0x00000100 /* Cyclic RSSI threshold 3 (field) (?) */ +#define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR_EN 0x00008000 /* Enable 1A RSSI threshold (?) */ +#define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR 0x00010000 /* 1A RSSI threshold (field) (?) */ +#define AR5K_PHY_OFDM_SELFCORR_LSCTHR_HIRSSI 0x00800000 /* Long sc threshold hi rssi (?) */ + +/* + * PHY-only warm reset register + */ +#define AR5K_PHY_WARM_RESET 0x9928 + +/* + * PHY-only control register + */ +#define AR5K_PHY_CTL 0x992c /* Register Address */ +#define AR5K_PHY_CTL_RX_DRAIN_RATE 0x00000001 /* RX drain rate (?) */ +#define AR5K_PHY_CTL_LATE_TX_SIG_SYM 0x00000002 /* Late tx signal symbol (?) */ +#define AR5K_PHY_CTL_GEN_SCRAMBLER 0x00000004 /* Generate scrambler */ +#define AR5K_PHY_CTL_TX_ANT_SEL 0x00000008 /* TX antenna select */ +#define AR5K_PHY_CTL_TX_ANT_STATIC 0x00000010 /* Static TX antenna */ +#define AR5K_PHY_CTL_RX_ANT_SEL 0x00000020 /* RX antenna select */ +#define AR5K_PHY_CTL_RX_ANT_STATIC 0x00000040 /* Static RX antenna */ +#define AR5K_PHY_CTL_LOW_FREQ_SLE_EN 0x00000080 /* Enable low freq sleep */ /* * PHY PAPD probe register [5111+ (?)] @@ -1816,9 +2193,13 @@ * Because it's always 0 in 5211 initialization code */ #define AR5K_PHY_PAPD_PROBE 0x9930 +#define AR5K_PHY_PAPD_PROBE_SH_HI_PAR 0x00000001 +#define AR5K_PHY_PAPD_PROBE_PCDAC_BIAS 0x00000002 +#define AR5K_PHY_PAPD_PROBE_COMP_GAIN 0x00000040 #define AR5K_PHY_PAPD_PROBE_TXPOWER 0x00007e00 #define AR5K_PHY_PAPD_PROBE_TXPOWER_S 9 #define AR5K_PHY_PAPD_PROBE_TX_NEXT 0x00008000 +#define AR5K_PHY_PAPD_PROBE_PREDIST_EN 0x00010000 #define AR5K_PHY_PAPD_PROBE_TYPE 0x01800000 /* [5112+] */ #define AR5K_PHY_PAPD_PROBE_TYPE_S 23 #define AR5K_PHY_PAPD_PROBE_TYPE_OFDM 0 @@ -1848,15 +2229,16 @@ #define AR5K_PHY_FRAME_CTL (ah->ah_version == AR5K_AR5210 ? \ AR5K_PHY_FRAME_CTL_5210 : AR5K_PHY_FRAME_CTL_5211) /*---[5111+]---*/ -#define AR5K_PHY_FRAME_CTL_TX_CLIP 0x00000038 +#define AR5K_PHY_FRAME_CTL_TX_CLIP 0x00000038 /* Mask for tx clip (?) */ #define AR5K_PHY_FRAME_CTL_TX_CLIP_S 3 +#define AR5K_PHY_FRAME_CTL_PREP_CHINFO 0x00010000 /* Prepend chan info */ /*---[5110/5111]---*/ -#define AR5K_PHY_FRAME_CTL_TIMING_ERR 0x01000000 -#define AR5K_PHY_FRAME_CTL_PARITY_ERR 0x02000000 -#define AR5K_PHY_FRAME_CTL_ILLRATE_ERR 0x04000000 /* illegal rate */ -#define AR5K_PHY_FRAME_CTL_ILLLEN_ERR 0x08000000 /* illegal length */ +#define AR5K_PHY_FRAME_CTL_TIMING_ERR 0x01000000 /* PHY timing error */ +#define AR5K_PHY_FRAME_CTL_PARITY_ERR 0x02000000 /* Parity error */ +#define AR5K_PHY_FRAME_CTL_ILLRATE_ERR 0x04000000 /* Illegal rate */ +#define AR5K_PHY_FRAME_CTL_ILLLEN_ERR 0x08000000 /* Illegal length */ #define AR5K_PHY_FRAME_CTL_SERVICE_ERR 0x20000000 -#define AR5K_PHY_FRAME_CTL_TXURN_ERR 0x40000000 /* tx underrun */ +#define AR5K_PHY_FRAME_CTL_TXURN_ERR 0x40000000 /* TX underrun */ #define AR5K_PHY_FRAME_CTL_INI AR5K_PHY_FRAME_CTL_SERVICE_ERR | \ AR5K_PHY_FRAME_CTL_TXURN_ERR | \ AR5K_PHY_FRAME_CTL_ILLLEN_ERR | \ @@ -1915,6 +2297,11 @@ after DFS is enabled */ #define AR5K_PHY_ANT_SWITCH_TABLE_1 0x9964 /* + * PHY Noise floor threshold + */ +#define AR5K_PHY_NFTHRES 0x9968 + +/* * PHY clock sleep registers [5112+] */ #define AR5K_PHY_SCLOCK 0x99f0 @@ -1922,56 +2309,116 @@ after DFS is enabled */ #define AR5K_PHY_SDELAY 0x99f4 #define AR5K_PHY_SDELAY_32MHZ 0x000000ff #define AR5K_PHY_SPENDING 0x99f8 +#define AR5K_PHY_SPENDING_14 0x00000014 +#define AR5K_PHY_SPENDING_18 0x00000018 #define AR5K_PHY_SPENDING_RF5111 0x00000018 -#define AR5K_PHY_SPENDING_RF5112 0x00000014 /* <- i 've only seen this on 2425 dumps ! */ -#define AR5K_PHY_SPENDING_RF5112A 0x0000000e /* but since i only have 5112A-based chips */ -#define AR5K_PHY_SPENDING_RF5424 0x00000012 /* to test it might be also for old 5112. */ +#define AR5K_PHY_SPENDING_RF5112 0x00000014 +/* #define AR5K_PHY_SPENDING_RF5112A 0x0000000e */ +/* #define AR5K_PHY_SPENDING_RF5424 0x00000012 */ +#define AR5K_PHY_SPENDING_RF5413 0x00000014 +#define AR5K_PHY_SPENDING_RF2413 0x00000014 +#define AR5K_PHY_SPENDING_RF2425 0x00000018 /* * Misc PHY/radio registers [5110 - 5111] */ -#define AR5K_BB_GAIN_BASE 0x9b00 /* BaseBand Amplifier Gain table base address */ +#define AR5K_BB_GAIN_BASE 0x9b00 /* BaseBand Amplifier Gain table base address */ #define AR5K_BB_GAIN(_n) (AR5K_BB_GAIN_BASE + ((_n) << 2)) -#define AR5K_RF_GAIN_BASE 0x9a00 /* RF Amplrifier Gain table base address */ +#define AR5K_RF_GAIN_BASE 0x9a00 /* RF Amplrifier Gain table base address */ #define AR5K_RF_GAIN(_n) (AR5K_RF_GAIN_BASE + ((_n) << 2)) /* * PHY timing IQ calibration result register [5111+] */ -#define AR5K_PHY_IQRES_CAL_PWR_I 0x9c10 /* I (Inphase) power value */ -#define AR5K_PHY_IQRES_CAL_PWR_Q 0x9c14 /* Q (Quadrature) power value */ +#define AR5K_PHY_IQRES_CAL_PWR_I 0x9c10 /* I (Inphase) power value */ +#define AR5K_PHY_IQRES_CAL_PWR_Q 0x9c14 /* Q (Quadrature) power value */ #define AR5K_PHY_IQRES_CAL_CORR 0x9c18 /* I/Q Correlation */ /* * PHY current RSSI register [5111+] */ -#define AR5K_PHY_CURRENT_RSSI 0x9c1c +#define AR5K_PHY_CURRENT_RSSI 0x9c1c + +/* + * PHY RF Bus grant register (?) + */ +#define AR5K_PHY_RFBUS_GRANT 0x9c20 + +/* + * PHY ADC test register + */ +#define AR5K_PHY_ADC_TEST 0x9c24 +#define AR5K_PHY_ADC_TEST_I 0x00000001 +#define AR5K_PHY_ADC_TEST_Q 0x00000200 + +/* + * PHY DAC test register + */ +#define AR5K_PHY_DAC_TEST 0x9c28 +#define AR5K_PHY_DAC_TEST_I 0x00000001 +#define AR5K_PHY_DAC_TEST_Q 0x00000200 + +/* + * PHY PTAT register (?) + */ +#define AR5K_PHY_PTAT 0x9c2c + +/* + * PHY Illegal TX rate register [5112+] + */ +#define AR5K_PHY_BAD_TX_RATE 0x9c30 + +/* + * PHY SPUR Power register [5112+] + */ +#define AR5K_PHY_SPUR_PWR 0x9c34 /* Register Address */ +#define AR5K_PHY_SPUR_PWR_I 0x00000001 /* SPUR Power estimate for I (field) */ +#define AR5K_PHY_SPUR_PWR_Q 0x00000100 /* SPUR Power estimate for Q (field) */ +#define AR5K_PHY_SPUR_PWR_FILT 0x00010000 /* Power with SPUR removed (field) */ + +/* + * PHY Channel status register [5112+] (?) + */ +#define AR5K_PHY_CHAN_STATUS 0x9c38 +#define AR5K_PHY_CHAN_STATUS_BT_ACT 0x00000001 +#define AR5K_PHY_CHAN_STATUS_RX_CLR_RAW 0x00000002 +#define AR5K_PHY_CHAN_STATUS_RX_CLR_MAC 0x00000004 +#define AR5K_PHY_CHAN_STATUS_RX_CLR_PAP 0x00000008 + +/* + * PHY PAPD I (power?) table (?) + * (92! entries) + */ +#define AR5K_PHY_PAPD_I_BASE 0xa000 +#define AR5K_PHY_PAPD_I(_n) (AR5K_PHY_PAPD_I_BASE + ((_n) << 2)) /* * PHY PCDAC TX power table */ #define AR5K_PHY_PCDAC_TXPOWER_BASE_5211 0xa180 -#define AR5K_PHY_PCDAC_TXPOWER_BASE_5413 0xa280 -#define AR5K_PHY_PCDAC_TXPOWER_BASE (ah->ah_radio >= AR5K_RF5413 ? \ - AR5K_PHY_PCDAC_TXPOWER_BASE_5413 :\ +#define AR5K_PHY_PCDAC_TXPOWER_BASE_2413 0xa280 +#define AR5K_PHY_PCDAC_TXPOWER_BASE (ah->ah_radio >= AR5K_RF2413 ? \ + AR5K_PHY_PCDAC_TXPOWER_BASE_2413 :\ AR5K_PHY_PCDAC_TXPOWER_BASE_5211) #define AR5K_PHY_PCDAC_TXPOWER(_n) (AR5K_PHY_PCDAC_TXPOWER_BASE + ((_n) << 2)) /* * PHY mode register [5111+] */ -#define AR5K_PHY_MODE 0x0a200 /* Register address */ -#define AR5K_PHY_MODE_MOD 0x00000001 /* PHY Modulation mask*/ +#define AR5K_PHY_MODE 0x0a200 /* Register Address */ +#define AR5K_PHY_MODE_MOD 0x00000001 /* PHY Modulation bit */ #define AR5K_PHY_MODE_MOD_OFDM 0 #define AR5K_PHY_MODE_MOD_CCK 1 -#define AR5K_PHY_MODE_FREQ 0x00000002 /* Freq mode mask */ +#define AR5K_PHY_MODE_FREQ 0x00000002 /* Freq mode bit */ #define AR5K_PHY_MODE_FREQ_5GHZ 0 #define AR5K_PHY_MODE_FREQ_2GHZ 2 -#define AR5K_PHY_MODE_MOD_DYN 0x00000004 /* Dynamic OFDM/CCK mode mask [5112+] */ +#define AR5K_PHY_MODE_MOD_DYN 0x00000004 /* Enable Dynamic OFDM/CCK mode [5112+] */ #define AR5K_PHY_MODE_RAD 0x00000008 /* [5212+] */ #define AR5K_PHY_MODE_RAD_RF5111 0 #define AR5K_PHY_MODE_RAD_RF5112 8 -#define AR5K_PHY_MODE_XR 0x00000010 /* [5112+] */ +#define AR5K_PHY_MODE_XR 0x00000010 /* Enable XR mode [5112+] */ +#define AR5K_PHY_MODE_HALF_RATE 0x00000020 /* Enable Half rate (test) */ +#define AR5K_PHY_MODE_QUARTER_RATE 0x00000040 /* Enable Quarter rat (test) */ /* * PHY CCK transmit control register [5111+ (?)] @@ -1979,6 +2426,15 @@ after DFS is enabled */ #define AR5K_PHY_CCKTXCTL 0xa204 #define AR5K_PHY_CCKTXCTL_WORLD 0x00000000 #define AR5K_PHY_CCKTXCTL_JAPAN 0x00000010 +#define AR5K_PHY_CCKTXCTL_SCRAMBLER_DIS 0x00000001 +#define AR5K_PHY_CCKTXCTK_DAC_SCALE 0x00000004 + +/* + * PHY CCK Cross-correlator Barker RSSI threshold register [5212+] + */ +#define AR5K_PHY_CCK_CROSSCORR 0xa208 +#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR 0x0000000f +#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR_S 0 /* * PHY 2GHz gain register [5111+] diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c index 1acfbcd..9509fd2 100644 --- a/drivers/net/wireless/ipw2200.c +++ b/drivers/net/wireless/ipw2200.c @@ -305,9 +305,10 @@ static inline void ipw_write_reg32(struct ipw_priv *a, u32 b, u32 c) #define _ipw_write8(ipw, ofs, val) writeb((val), (ipw)->hw_base + (ofs)) /* 8-bit direct write (for low 4K of SRAM/regs), with debug wrapper */ -#define ipw_write8(ipw, ofs, val) \ +#define ipw_write8(ipw, ofs, val) do { \ IPW_DEBUG_IO("%s %d: write_direct8(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(ofs), (u32)(val)); \ - _ipw_write8(ipw, ofs, val) + _ipw_write8(ipw, ofs, val); \ + } while (0) /* 16-bit direct write (low 4K) */ #define _ipw_write16(ipw, ofs, val) writew((val), (ipw)->hw_base + (ofs)) diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.c b/drivers/net/wireless/iwlwifi/iwl-3945.c index a51e0ea..56a9361 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945.c @@ -710,10 +710,7 @@ static void iwl3945_rx_reply_rx(struct iwl3945_priv *priv, return; } - if (priv->iw_mode == IEEE80211_IF_TYPE_MNTR) { - iwl3945_pass_packet_to_mac80211(priv, rxb, &rx_status); - return; - } + /* Convert 3945's rssi indicator to dBm */ rx_status.signal = rx_stats->rssi - IWL_RSSI_OFFSET; @@ -775,6 +772,11 @@ static void iwl3945_rx_reply_rx(struct iwl3945_priv *priv, priv->last_rx_noise = rx_status.noise; } + if (priv->iw_mode == IEEE80211_IF_TYPE_MNTR) { + iwl3945_pass_packet_to_mac80211(priv, rxb, &rx_status); + return; + } + switch (le16_to_cpu(header->frame_control) & IEEE80211_FCTL_FTYPE) { case IEEE80211_FTYPE_MGMT: switch (le16_to_cpu(header->frame_control) & diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index f72cd0b..0182e4d 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -962,16 +962,16 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb) if (ret) return ret; - if ((iwl_queue_space(q) < q->high_mark) - && priv->mac80211_registered) { + if ((iwl_queue_space(q) < q->high_mark) && priv->mac80211_registered) { if (wait_write_ptr) { spin_lock_irqsave(&priv->lock, flags); txq->need_update = 1; iwl_txq_update_write_ptr(priv, txq); spin_unlock_irqrestore(&priv->lock, flags); + } else { + ieee80211_stop_queue(priv->hw, + skb_get_queue_mapping(skb)); } - - ieee80211_stop_queue(priv->hw, skb_get_queue_mapping(skb)); } return 0; diff --git a/drivers/net/wireless/libertas/main.c b/drivers/net/wireless/libertas/main.c index 14d5d61..bd32ac0 100644 --- a/drivers/net/wireless/libertas/main.c +++ b/drivers/net/wireless/libertas/main.c @@ -297,9 +297,7 @@ static ssize_t lbs_rtap_set(struct device *dev, lbs_add_rtap(priv); } priv->monitormode = monitor_mode; - } - - else { + } else { if (!priv->monitormode) return strlen(buf); priv->monitormode = 0; @@ -1242,8 +1240,6 @@ int lbs_start_card(struct lbs_private *priv) lbs_pr_err("cannot register ethX device\n"); goto done; } - if (device_create_file(&dev->dev, &dev_attr_lbs_rtap)) - lbs_pr_err("cannot register lbs_rtap attribute\n"); lbs_update_channel(priv); @@ -1275,6 +1271,13 @@ int lbs_start_card(struct lbs_private *priv) if (device_create_file(&dev->dev, &dev_attr_lbs_mesh)) lbs_pr_err("cannot register lbs_mesh attribute\n"); + + /* While rtap isn't related to mesh, only mesh-enabled + * firmware implements the rtap functionality via + * CMD_802_11_MONITOR_MODE. + */ + if (device_create_file(&dev->dev, &dev_attr_lbs_rtap)) + lbs_pr_err("cannot register lbs_rtap attribute\n"); } } @@ -1306,9 +1309,9 @@ void lbs_stop_card(struct lbs_private *priv) netif_carrier_off(priv->dev); lbs_debugfs_remove_one(priv); - device_remove_file(&dev->dev, &dev_attr_lbs_rtap); if (priv->mesh_tlv) { device_remove_file(&dev->dev, &dev_attr_lbs_mesh); + device_remove_file(&dev->dev, &dev_attr_lbs_rtap); } /* Flush pending command nodes */ diff --git a/drivers/net/wireless/prism54/isl_ioctl.c b/drivers/net/wireless/prism54/isl_ioctl.c index 97fa14e..3d75a71 100644 --- a/drivers/net/wireless/prism54/isl_ioctl.c +++ b/drivers/net/wireless/prism54/isl_ioctl.c @@ -2518,7 +2518,7 @@ enum { #define PRISM2_HOSTAPD_MAX_BUF_SIZE 1024 #define PRISM2_HOSTAPD_GENERIC_ELEMENT_HDR_LEN \ -((int) (&((struct prism2_hostapd_param *) 0)->u.generic_elem.data)) + offsetof(struct prism2_hostapd_param, u.generic_elem.data) /* Maximum length for algorithm names (-1 for nul termination) * used in ioctl() */ diff --git a/drivers/net/wireless/rt2x00/rt2500pci.c b/drivers/net/wireless/rt2x00/rt2500pci.c index aa6dfb8..181a146 100644 --- a/drivers/net/wireless/rt2x00/rt2500pci.c +++ b/drivers/net/wireless/rt2x00/rt2500pci.c @@ -1220,6 +1220,7 @@ static void rt2500pci_write_tx_desc(struct rt2x00_dev *rt2x00dev, rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->ifs); rt2x00_set_field32(&word, TXD_W0_RETRY_MODE, test_bit(ENTRY_TXD_RETRY_MODE, &txdesc->flags)); + rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, skb->len); rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, CIPHER_NONE); rt2x00_desc_write(txd, 0, word); } diff --git a/drivers/net/wireless/rt2x00/rt2500usb.c b/drivers/net/wireless/rt2x00/rt2500usb.c index 3078417..c6f6eb6 100644 --- a/drivers/net/wireless/rt2x00/rt2500usb.c +++ b/drivers/net/wireless/rt2x00/rt2500usb.c @@ -1376,6 +1376,9 @@ static int rt2500usb_validate_eeprom(struct rt2x00_dev *rt2x00dev) rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); EEPROM(rt2x00dev, "BBPtune vgc: 0x%04x\n", word); + } else { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); } rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R17, &word); @@ -1384,9 +1387,6 @@ static int rt2500usb_validate_eeprom(struct rt2x00_dev *rt2x00dev) rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_HIGH, 0x41); rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R17, word); EEPROM(rt2x00dev, "BBPtune r17: 0x%04x\n", word); - } else { - rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); - rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); } rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24, &word); diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h index db2dc97..8b10ea4 100644 --- a/drivers/net/wireless/rt2x00/rt2x00.h +++ b/drivers/net/wireless/rt2x00/rt2x00.h @@ -368,6 +368,12 @@ struct rt2x00_intf { #define DELAYED_CONFIG_ERP 0x00000002 #define DELAYED_LED_ASSOC 0x00000004 + /* + * Software sequence counter, this is only required + * for hardware which doesn't support hardware + * sequence counting. + */ + spinlock_t seqlock; u16 seqno; }; diff --git a/drivers/net/wireless/rt2x00/rt2x00config.c b/drivers/net/wireless/rt2x00/rt2x00config.c index 3f89516..d134c3b 100644 --- a/drivers/net/wireless/rt2x00/rt2x00config.c +++ b/drivers/net/wireless/rt2x00/rt2x00config.c @@ -254,6 +254,8 @@ config: libconf.ant.rx = default_ant->rx; else if (active_ant->rx == ANTENNA_SW_DIVERSITY) libconf.ant.rx = ANTENNA_B; + else + libconf.ant.rx = active_ant->rx; if (conf->antenna_sel_tx) libconf.ant.tx = conf->antenna_sel_tx; @@ -261,6 +263,8 @@ config: libconf.ant.tx = default_ant->tx; else if (active_ant->tx == ANTENNA_SW_DIVERSITY) libconf.ant.tx = ANTENNA_B; + else + libconf.ant.tx = active_ant->tx; } if (flags & CONFIG_UPDATE_SLOT_TIME) { diff --git a/drivers/net/wireless/rt2x00/rt2x00debug.c b/drivers/net/wireless/rt2x00/rt2x00debug.c index 300cf06..6bee1d6 100644 --- a/drivers/net/wireless/rt2x00/rt2x00debug.c +++ b/drivers/net/wireless/rt2x00/rt2x00debug.c @@ -372,9 +372,6 @@ static ssize_t rt2x00debug_write_##__name(struct file *file, \ if (*offset) \ return 0; \ \ - if (!capable(CAP_NET_ADMIN)) \ - return -EPERM; \ - \ if (intf->offset_##__name >= debug->__name.word_count) \ return -EINVAL; \ \ @@ -454,7 +451,7 @@ static struct dentry *rt2x00debug_create_file_driver(const char *name, data += sprintf(data, "compiled: %s %s\n", __DATE__, __TIME__); blob->size = strlen(blob->data); - return debugfs_create_blob(name, S_IRUGO, intf->driver_folder, blob); + return debugfs_create_blob(name, S_IRUSR, intf->driver_folder, blob); } static struct dentry *rt2x00debug_create_file_chipset(const char *name, @@ -482,7 +479,7 @@ static struct dentry *rt2x00debug_create_file_chipset(const char *name, data += sprintf(data, "rf length: %d\n", debug->rf.word_count); blob->size = strlen(blob->data); - return debugfs_create_blob(name, S_IRUGO, intf->driver_folder, blob); + return debugfs_create_blob(name, S_IRUSR, intf->driver_folder, blob); } void rt2x00debug_register(struct rt2x00_dev *rt2x00dev) @@ -517,7 +514,7 @@ void rt2x00debug_register(struct rt2x00_dev *rt2x00dev) if (IS_ERR(intf->chipset_entry)) goto exit; - intf->dev_flags = debugfs_create_file("dev_flags", S_IRUGO, + intf->dev_flags = debugfs_create_file("dev_flags", S_IRUSR, intf->driver_folder, intf, &rt2x00debug_fop_dev_flags); if (IS_ERR(intf->dev_flags)) @@ -532,7 +529,7 @@ void rt2x00debug_register(struct rt2x00_dev *rt2x00dev) ({ \ (__intf)->__name##_off_entry = \ debugfs_create_u32(__stringify(__name) "_offset", \ - S_IRUGO | S_IWUSR, \ + S_IRUSR | S_IWUSR, \ (__intf)->register_folder, \ &(__intf)->offset_##__name); \ if (IS_ERR((__intf)->__name##_off_entry)) \ @@ -540,7 +537,7 @@ void rt2x00debug_register(struct rt2x00_dev *rt2x00dev) \ (__intf)->__name##_val_entry = \ debugfs_create_file(__stringify(__name) "_value", \ - S_IRUGO | S_IWUSR, \ + S_IRUSR | S_IWUSR, \ (__intf)->register_folder, \ (__intf), &rt2x00debug_fop_##__name);\ if (IS_ERR((__intf)->__name##_val_entry)) \ @@ -560,7 +557,7 @@ void rt2x00debug_register(struct rt2x00_dev *rt2x00dev) goto exit; intf->queue_frame_dump_entry = - debugfs_create_file("dump", S_IRUGO, intf->queue_folder, + debugfs_create_file("dump", S_IRUSR, intf->queue_folder, intf, &rt2x00debug_fop_queue_dump); if (IS_ERR(intf->queue_frame_dump_entry)) goto exit; @@ -569,7 +566,7 @@ void rt2x00debug_register(struct rt2x00_dev *rt2x00dev) init_waitqueue_head(&intf->frame_dump_waitqueue); intf->queue_stats_entry = - debugfs_create_file("queue", S_IRUGO, intf->queue_folder, + debugfs_create_file("queue", S_IRUSR, intf->queue_folder, intf, &rt2x00debug_fop_queue_stats); return; diff --git a/drivers/net/wireless/rt2x00/rt2x00mac.c b/drivers/net/wireless/rt2x00/rt2x00mac.c index c3ee4ec..bd422fd 100644 --- a/drivers/net/wireless/rt2x00/rt2x00mac.c +++ b/drivers/net/wireless/rt2x00/rt2x00mac.c @@ -247,6 +247,7 @@ int rt2x00mac_add_interface(struct ieee80211_hw *hw, rt2x00dev->intf_sta_count++; spin_lock_init(&intf->lock); + spin_lock_init(&intf->seqlock); intf->beacon = entry; if (conf->type == IEEE80211_IF_TYPE_AP) diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.c b/drivers/net/wireless/rt2x00/rt2x00queue.c index 3b27f6a..898cdd7 100644 --- a/drivers/net/wireless/rt2x00/rt2x00queue.c +++ b/drivers/net/wireless/rt2x00/rt2x00queue.c @@ -128,6 +128,7 @@ static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry, unsigned int data_length; unsigned int duration; unsigned int residual; + unsigned long irqflags; memset(txdesc, 0, sizeof(*txdesc)); @@ -213,14 +214,14 @@ static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry, * sequence counter given by mac80211. */ if (tx_info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { - spin_lock(&intf->lock); + spin_lock_irqsave(&intf->seqlock, irqflags); if (test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags)) intf->seqno += 0x10; hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); hdr->seq_ctrl |= cpu_to_le16(intf->seqno); - spin_unlock(&intf->lock); + spin_unlock_irqrestore(&intf->seqlock, irqflags); __set_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags); } diff --git a/drivers/net/wireless/rt2x00/rt61pci.c b/drivers/net/wireless/rt2x00/rt61pci.c index fbe2a65..087e90b 100644 --- a/drivers/net/wireless/rt2x00/rt61pci.c +++ b/drivers/net/wireless/rt2x00/rt61pci.c @@ -1004,6 +1004,11 @@ static int rt61pci_load_firmware(struct rt2x00_dev *rt2x00dev, const void *data, } /* + * Hardware needs another millisecond before it is ready. + */ + msleep(1); + + /* * Reset MAC and BBP registers. */ reg = 0; diff --git a/drivers/net/wireless/rtl8187.h b/drivers/net/wireless/rtl8187.h index 1b0d750..5a9515c 100644 --- a/drivers/net/wireless/rtl8187.h +++ b/drivers/net/wireless/rtl8187.h @@ -94,6 +94,10 @@ struct rtl8187_priv { const struct rtl818x_rf_ops *rf; struct ieee80211_vif *vif; int mode; + /* The mutex protects the TX loopback state. + * Any attempt to set channels concurrently locks the device. + */ + struct mutex conf_mutex; /* rtl8187 specific */ struct ieee80211_channel channels[14]; diff --git a/drivers/net/wireless/rtl8187_dev.c b/drivers/net/wireless/rtl8187_dev.c index 177988e..57376fb 100644 --- a/drivers/net/wireless/rtl8187_dev.c +++ b/drivers/net/wireless/rtl8187_dev.c @@ -31,6 +31,8 @@ MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver"); MODULE_LICENSE("GPL"); static struct usb_device_id rtl8187_table[] __devinitdata = { + /* Asus */ + {USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187}, /* Realtek */ {USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187}, {USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B}, @@ -726,6 +728,7 @@ static int rtl8187_start(struct ieee80211_hw *dev) if (ret) return ret; + mutex_lock(&priv->conf_mutex); if (priv->is_rtl8187b) { reg = RTL818X_RX_CONF_MGMT | RTL818X_RX_CONF_DATA | @@ -747,6 +750,7 @@ static int rtl8187_start(struct ieee80211_hw *dev) (7 << 0 /* long retry limit */) | (7 << 21 /* MAX TX DMA */)); rtl8187_init_urbs(dev); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -790,6 +794,7 @@ static int rtl8187_start(struct ieee80211_hw *dev) reg |= RTL818X_CMD_TX_ENABLE; reg |= RTL818X_CMD_RX_ENABLE; rtl818x_iowrite8(priv, &priv->map->CMD, reg); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -801,6 +806,7 @@ static void rtl8187_stop(struct ieee80211_hw *dev) struct sk_buff *skb; u32 reg; + mutex_lock(&priv->conf_mutex); rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); reg = rtl818x_ioread8(priv, &priv->map->CMD); @@ -820,7 +826,7 @@ static void rtl8187_stop(struct ieee80211_hw *dev) usb_kill_urb(info->urb); kfree_skb(skb); } - return; + mutex_unlock(&priv->conf_mutex); } static int rtl8187_add_interface(struct ieee80211_hw *dev, @@ -840,6 +846,7 @@ static int rtl8187_add_interface(struct ieee80211_hw *dev, return -EOPNOTSUPP; } + mutex_lock(&priv->conf_mutex); priv->vif = conf->vif; rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); @@ -848,6 +855,7 @@ static int rtl8187_add_interface(struct ieee80211_hw *dev, ((u8 *)conf->mac_addr)[i]); rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -855,8 +863,10 @@ static void rtl8187_remove_interface(struct ieee80211_hw *dev, struct ieee80211_if_init_conf *conf) { struct rtl8187_priv *priv = dev->priv; + mutex_lock(&priv->conf_mutex); priv->mode = IEEE80211_IF_TYPE_MNTR; priv->vif = NULL; + mutex_unlock(&priv->conf_mutex); } static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) @@ -864,6 +874,7 @@ static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) struct rtl8187_priv *priv = dev->priv; u32 reg; + mutex_lock(&priv->conf_mutex); reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); /* Enable TX loopback on MAC level to avoid TX during channel * changes, as this has be seen to causes problems and the @@ -896,6 +907,7 @@ static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100); rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100); rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -907,6 +919,7 @@ static int rtl8187_config_interface(struct ieee80211_hw *dev, int i; u8 reg; + mutex_lock(&priv->conf_mutex); for (i = 0; i < ETH_ALEN; i++) rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]); @@ -920,6 +933,7 @@ static int rtl8187_config_interface(struct ieee80211_hw *dev, rtl818x_iowrite8(priv, &priv->map->MSR, reg); } + mutex_unlock(&priv->conf_mutex); return 0; } @@ -1187,6 +1201,7 @@ static int __devinit rtl8187_probe(struct usb_interface *intf, printk(KERN_ERR "rtl8187: Cannot register device\n"); goto err_free_dev; } + mutex_init(&priv->conf_mutex); printk(KERN_INFO "%s: hwaddr %s, %s V%d + %s\n", wiphy_name(dev->wiphy), print_mac(mac, dev->wiphy->perm_addr), diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h index a4f9a83..a2e200f 100644 --- a/net/mac80211/ieee80211_i.h +++ b/net/mac80211/ieee80211_i.h @@ -586,6 +586,7 @@ struct ieee80211_local { struct timer_list sta_cleanup; unsigned long queues_pending[BITS_TO_LONGS(IEEE80211_MAX_QUEUES)]; + unsigned long queues_pending_run[BITS_TO_LONGS(IEEE80211_MAX_QUEUES)]; struct ieee80211_tx_stored_packet pending_packet[IEEE80211_MAX_QUEUES]; struct tasklet_struct tx_pending_tasklet; diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c index 69019e9..771ec68 100644 --- a/net/mac80211/tx.c +++ b/net/mac80211/tx.c @@ -1060,13 +1060,14 @@ static int ieee80211_tx_prepare(struct ieee80211_tx_data *tx, static int __ieee80211_tx(struct ieee80211_local *local, struct sk_buff *skb, struct ieee80211_tx_data *tx) { - struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); + struct ieee80211_tx_info *info; int ret, i; - if (netif_subqueue_stopped(local->mdev, skb)) - return IEEE80211_TX_AGAIN; - if (skb) { + if (netif_subqueue_stopped(local->mdev, skb)) + return IEEE80211_TX_AGAIN; + info = IEEE80211_SKB_CB(skb); + ieee80211_dump_frame(wiphy_name(local->hw.wiphy), "TX to low-level driver", skb); ret = local->ops->tx(local_to_hw(local), skb); @@ -1215,6 +1216,7 @@ retry: if (ret == IEEE80211_TX_FRAG_AGAIN) skb = NULL; + set_bit(queue, local->queues_pending); smp_mb(); /* @@ -1708,14 +1710,19 @@ void ieee80211_tx_pending(unsigned long data) netif_tx_lock_bh(dev); for (i = 0; i < ieee80211_num_regular_queues(&local->hw); i++) { /* Check that this queue is ok */ - if (__netif_subqueue_stopped(local->mdev, i)) + if (__netif_subqueue_stopped(local->mdev, i) && + !test_bit(i, local->queues_pending_run)) continue; if (!test_bit(i, local->queues_pending)) { + clear_bit(i, local->queues_pending_run); ieee80211_wake_queue(&local->hw, i); continue; } + clear_bit(i, local->queues_pending_run); + netif_start_subqueue(local->mdev, i); + store = &local->pending_packet[i]; tx.extra_frag = store->extra_frag; tx.num_extra_frag = store->num_extra_frag; diff --git a/net/mac80211/util.c b/net/mac80211/util.c index 19f85e1..0d463c8 100644 --- a/net/mac80211/util.c +++ b/net/mac80211/util.c @@ -361,6 +361,7 @@ void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue) struct ieee80211_local *local = hw_to_local(hw); if (test_bit(queue, local->queues_pending)) { + set_bit(queue, local->queues_pending_run); tasklet_schedule(&local->tx_pending_tasklet); } else { netif_wake_subqueue(local->mdev, queue); diff --git a/net/rfkill/rfkill-input.c b/net/rfkill/rfkill-input.c index 8aa8227..e5b6955 100644 --- a/net/rfkill/rfkill-input.c +++ b/net/rfkill/rfkill-input.c @@ -109,6 +109,25 @@ static DEFINE_RFKILL_TASK(rfkill_uwb, RFKILL_TYPE_UWB); static DEFINE_RFKILL_TASK(rfkill_wimax, RFKILL_TYPE_WIMAX); static DEFINE_RFKILL_TASK(rfkill_wwan, RFKILL_TYPE_WWAN); +static void rfkill_schedule_evsw_rfkillall(int state) +{ + /* EVERY radio type. state != 0 means radios ON */ + /* handle EPO (emergency power off) through shortcut */ + if (state) { + rfkill_schedule_set(&rfkill_wwan, + RFKILL_STATE_UNBLOCKED); + rfkill_schedule_set(&rfkill_wimax, + RFKILL_STATE_UNBLOCKED); + rfkill_schedule_set(&rfkill_uwb, + RFKILL_STATE_UNBLOCKED); + rfkill_schedule_set(&rfkill_bt, + RFKILL_STATE_UNBLOCKED); + rfkill_schedule_set(&rfkill_wlan, + RFKILL_STATE_UNBLOCKED); + } else + rfkill_schedule_epo(); +} + static void rfkill_event(struct input_handle *handle, unsigned int type, unsigned int code, int data) { @@ -132,21 +151,7 @@ static void rfkill_event(struct input_handle *handle, unsigned int type, } else if (type == EV_SW) { switch (code) { case SW_RFKILL_ALL: - /* EVERY radio type. data != 0 means radios ON */ - /* handle EPO (emergency power off) through shortcut */ - if (data) { - rfkill_schedule_set(&rfkill_wwan, - RFKILL_STATE_UNBLOCKED); - rfkill_schedule_set(&rfkill_wimax, - RFKILL_STATE_UNBLOCKED); - rfkill_schedule_set(&rfkill_uwb, - RFKILL_STATE_UNBLOCKED); - rfkill_schedule_set(&rfkill_bt, - RFKILL_STATE_UNBLOCKED); - rfkill_schedule_set(&rfkill_wlan, - RFKILL_STATE_UNBLOCKED); - } else - rfkill_schedule_epo(); + rfkill_schedule_evsw_rfkillall(data); break; default: break; @@ -168,6 +173,7 @@ static int rfkill_connect(struct input_handler *handler, struct input_dev *dev, handle->handler = handler; handle->name = "rfkill"; + /* causes rfkill_start() to be called */ error = input_register_handle(handle); if (error) goto err_free_handle; @@ -185,6 +191,23 @@ static int rfkill_connect(struct input_handler *handler, struct input_dev *dev, return error; } +static void rfkill_start(struct input_handle *handle) +{ + /* Take event_lock to guard against configuration changes, we + * should be able to deal with concurrency with rfkill_event() + * just fine (which event_lock will also avoid). */ + spin_lock_irq(&handle->dev->event_lock); + + if (test_bit(EV_SW, handle->dev->evbit)) { + if (test_bit(SW_RFKILL_ALL, handle->dev->swbit)) + rfkill_schedule_evsw_rfkillall(test_bit(SW_RFKILL_ALL, + handle->dev->sw)); + /* add resync for further EV_SW events here */ + } + + spin_unlock_irq(&handle->dev->event_lock); +} + static void rfkill_disconnect(struct input_handle *handle) { input_close_device(handle); @@ -225,6 +248,7 @@ static struct input_handler rfkill_handler = { .event = rfkill_event, .connect = rfkill_connect, .disconnect = rfkill_disconnect, + .start = rfkill_start, .name = "rfkill", .id_table = rfkill_ids, }; diff --git a/net/rfkill/rfkill.c b/net/rfkill/rfkill.c index c6f2f38..d2d4565 100644 --- a/net/rfkill/rfkill.c +++ b/net/rfkill/rfkill.c @@ -105,6 +105,16 @@ static void rfkill_led_trigger(struct rfkill *rfkill, #endif /* CONFIG_RFKILL_LEDS */ } +#ifdef CONFIG_RFKILL_LEDS +static void rfkill_led_trigger_activate(struct led_classdev *led) +{ + struct rfkill *rfkill = container_of(led->trigger, + struct rfkill, led_trigger); + + rfkill_led_trigger(rfkill, rfkill->state); +} +#endif /* CONFIG_RFKILL_LEDS */ + static void notify_rfkill_state_change(struct rfkill *rfkill) { blocking_notifier_call_chain(&rfkill_notifier_list, @@ -589,7 +599,10 @@ static void rfkill_led_trigger_register(struct rfkill *rfkill) #ifdef CONFIG_RFKILL_LEDS int error; - rfkill->led_trigger.name = rfkill->dev.bus_id; + if (!rfkill->led_trigger.name) + rfkill->led_trigger.name = rfkill->dev.bus_id; + if (!rfkill->led_trigger.activate) + rfkill->led_trigger.activate = rfkill_led_trigger_activate; error = led_trigger_register(&rfkill->led_trigger); if (error) rfkill->led_trigger.name = NULL; -- John W. Linville linville@xxxxxxxxxxxxx -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
