From: Sven Eckelmann <seckelmann@xxxxxxxxx>
The capabilities for the HE mesh are generated from the capabilities
reported by the fw. But the firmware only reports the overall capabilities
and not the one which are specific for mesh. Some of them (TWT, MU UL/DL,
TB PPDU, ...) require an infrastructure setup with a main STA (AP)
controlling the operations. This is not the case for mesh and thus these
capabilities are removed from the list of capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@xxxxxxxxx>
---
drivers/net/wireless/ath/ath11k/mac.c | 63 +++++++++++++++++++++++++++
1 file changed, 63 insertions(+)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 8c47e09a84e7..b55a98902fba 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -3274,6 +3274,7 @@ static int ath11k_mac_copy_he_cap(struct ath11k *ar,
switch (i) {
case NL80211_IFTYPE_STATION:
case NL80211_IFTYPE_AP:
+ case NL80211_IFTYPE_MESH_POINT:
break;
default:
@@ -3314,6 +3315,61 @@ static int ath11k_mac_copy_he_cap(struct ath11k *ar,
he_cap_elem->phy_cap_info[9] |=
IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU;
break;
+ case NL80211_IFTYPE_MESH_POINT:
+ he_cap_elem->mac_cap_info[0] &=
+ ~(IEEE80211_HE_MAC_CAP0_TWT_RES |
+ IEEE80211_HE_MAC_CAP0_TWT_REQ);
+ he_cap_elem->mac_cap_info[2] &=
+ ~(IEEE80211_HE_MAC_CAP2_TRS |
+ IEEE80211_HE_MAC_CAP2_BCAST_TWT |
+ IEEE80211_HE_MAC_CAP2_MU_CASCADING);
+ he_cap_elem->mac_cap_info[3] &=
+ ~(IEEE80211_HE_MAC_CAP3_FLEX_TWT_SCHED |
+ IEEE80211_HE_MAC_CAP2_BCAST_TWT |
+ IEEE80211_HE_MAC_CAP2_MU_CASCADING);
+ he_cap_elem->mac_cap_info[4] &=
+ ~(IEEE80211_HE_MAC_CAP4_BSRP_BQRP_A_MPDU_AGG |
+ IEEE80211_HE_MAC_CAP4_BQR);
+ he_cap_elem->mac_cap_info[5] &=
+ ~(IEEE80211_HE_MAC_CAP5_SUBCHAN_SELECVITE_TRANSMISSION |
+ IEEE80211_HE_MAC_CAP5_UL_2x996_TONE_RU |
+ IEEE80211_HE_MAC_CAP5_PUNCTURED_SOUNDING |
+ IEEE80211_HE_MAC_CAP5_HT_VHT_TRIG_FRAME_RX);
+
+ he_cap_elem->phy_cap_info[2] &=
+ ~(IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO |
+ IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO);
+ he_cap_elem->phy_cap_info[3] &=
+ ~(IEEE80211_HE_PHY_CAP3_RX_HE_MU_PPDU_FROM_NON_AP_STA |
+ IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_MASK |
+ IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_MASK);
+ he_cap_elem->phy_cap_info[4] &=
+ ~IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER;
+ he_cap_elem->phy_cap_info[5] &=
+ ~IEEE80211_HE_PHY_CAP5_NG16_MU_FEEDBACK;
+ he_cap_elem->phy_cap_info[6] &=
+ ~(IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_75_MU |
+ IEEE80211_HE_PHY_CAP6_TRIG_MU_BEAMFORMER_FB |
+ IEEE80211_HE_PHY_CAP6_TRIG_CQI_FB |
+ IEEE80211_HE_PHY_CAP6_PARTIAL_BANDWIDTH_DL_MUMIMO);
+ he_cap_elem->phy_cap_info[7] &=
+ ~(IEEE80211_HE_PHY_CAP7_SRP_BASED_SR |
+ IEEE80211_HE_PHY_CAP7_POWER_BOOST_FACTOR_AR |
+ IEEE80211_HE_PHY_CAP7_STBC_TX_ABOVE_80MHZ |
+ IEEE80211_HE_PHY_CAP7_STBC_RX_ABOVE_80MHZ);
+ he_cap_elem->phy_cap_info[8] &=
+ ~(IEEE80211_HE_PHY_CAP8_HE_ER_SU_PPDU_4XLTF_AND_08_US_GI |
+ IEEE80211_HE_PHY_CAP8_20MHZ_IN_40MHZ_HE_PPDU_IN_2G |
+ IEEE80211_HE_PHY_CAP8_20MHZ_IN_160MHZ_HE_PPDU |
+ IEEE80211_HE_PHY_CAP8_80MHZ_IN_160MHZ_HE_PPDU);
+ he_cap_elem->phy_cap_info[9] &=
+ ~(IEEE80211_HE_PHY_CAP9_LONGER_THAN_16_SIGB_OFDM_SYM |
+ IEEE80211_HE_PHY_CAP9_NON_TRIGGERED_CQI_FEEDBACK |
+ IEEE80211_HE_PHY_CAP9_RX_1024_QAM_LESS_THAN_242_TONE_RU |
+ IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU |
+ IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_COMP_SIGB |
+ IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_NON_COMP_SIGB);
+ break;
}
he_cap->he_mcs_nss_supp.rx_mcs_80 =
@@ -4239,6 +4295,13 @@ ath11k_mac_vdev_start_restart(struct ath11k_vif *arvif,
int he_support = arvif->vif->bss_conf.he_support;
int ret = 0;
+ /* mesh_point interfaces don't use bss_conf.he_support and still
+ * requires HE PHY mode to be set during vdev restart to avoid
+ * FW hangs when a sta with HE support tries to associate
+ */
+ if (arvif->vif->type == NL80211_IFTYPE_MESH_POINT)
+ he_support = true;
+
lockdep_assert_held(&ar->conf_mutex);
reinit_completion(&ar->vdev_setup_done);
--
2.20.1
