Search Linux Wireless

Re: [PATCH v3 04/11] pinctrl: sunxi: Support I/O bias voltage setting on H6

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Thu, Apr 11, 2019 at 12:19:44PM +0200, megous@xxxxxxxxxx wrote:
> From: Ondrej Jirman <megous@xxxxxxxxxx>
>
> H6 SoC has a "pio group withstand voltage mode" register (datasheet
> description), that needs to be used to select either 1.8V or 3.3V I/O mode,
> based on what voltage is powering the respective pin banks and is thus used
> for I/O signals.
>
> Add support for configuring this register according to the voltage of the
> pin bank regulator (if enabled).
>
> This is similar to the support for I/O bias voltage setting patch for A80
> and the same concerns apply. See:
>
>   commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
>
> Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
> ---
>  drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c |  1 +
>  drivers/pinctrl/sunxi/pinctrl-sunxi.c     | 11 +++++++++++
>  drivers/pinctrl/sunxi/pinctrl-sunxi.h     |  5 +++++
>  3 files changed, 17 insertions(+)
>
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
> index ef4268cc6227..3cc1121589c9 100644
> --- a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6.c
> @@ -591,6 +591,7 @@ static const struct sunxi_pinctrl_desc h6_pinctrl_data = {
>  	.irq_banks = 4,
>  	.irq_bank_map = h6_irq_bank_map,
>  	.irq_read_needs_mux = true,
> +	.io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
>  };
>
>  static int h6_pinctrl_probe(struct platform_device *pdev)
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
> index 98c4de5f4019..0cbca30b75dc 100644
> --- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c
> +++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
> @@ -614,6 +614,8 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
>  					 unsigned pin,
>  					 struct regulator *supply)
>  {
> +	unsigned short bank = pin / PINS_PER_BANK;
> +	unsigned long flags;
>  	u32 val, reg;
>  	int uV;
>
> @@ -651,6 +653,15 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
>  		reg &= ~IO_BIAS_MASK;
>  		writel(reg | val, pctl->membase + sunxi_grp_config_reg(pin));
>  		return 0;
> +	case BIAS_VOLTAGE_PIO_POW_MODE_SEL:
> +		val = uV <= 1800000 ? 1 : 0;
> +
> +		raw_spin_lock_irqsave(&pctl->lock, flags);
> +		reg = readl(pctl->membase + PIO_POW_MOD_SEL_REG);
> +		reg &= ~(1 << bank);
> +		writel(reg | val << bank, pctl->membase + PIO_POW_MOD_SEL_REG);
> +		raw_spin_unlock_irqrestore(&pctl->lock, flags);
> +		return 0;
>  	default:
>  		return -EINVAL;
>  	}
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.h b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
> index 4bfc8a6d9dce..36186906f0a7 100644
> --- a/drivers/pinctrl/sunxi/pinctrl-sunxi.h
> +++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
> @@ -95,11 +95,16 @@
>  #define PINCTRL_SUN7I_A20	BIT(7)
>  #define PINCTRL_SUN8I_R40	BIT(8)
>
> +#define PIO_POW_MOD_SEL_REG	0x340
> +
>  enum sunxi_desc_bias_voltage {
>  	BIAS_VOLTAGE_NONE,
>  	/* Bias voltage configuration is done through
>  	 * Pn_GRP_CONFIG registers, as seen on A80 SoC. */
>  	BIAS_VOLTAGE_GRP_CONFIG,
> +	/* Bias voltage is set through PIO_POW_MOD_SEL_REG
> +	 * register, as seen on H6 SoC, for example. */

That's not the proper comment style.

Once fixed, this patch and the previous is
Acked-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Wireless Regulations]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux