* Anders Roxell <anders.roxell@xxxxxxxxxx> [181211 23:45]: > I have different serious, one when our board hangs on udhcpc [1], then I see > wlcore and wl18xx_driver. Hmm so on what SoC is this with? Adding Eyeal to Cc here too. Regards, Tony > [ 8.824419] cfg80211: Loading compiled-in X.509 certificates for > regulatory database > [ 8.852546] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' > [ 8.861006] platform regulatory.0: Direct firmware load for > regulatory.db failed with error -2 > [ 8.870248] cfg80211: failed to load regulatory.db > [ 8.895501] asix 1-1.1:1.0 eth0: register 'asix' at > usb-f72c0000.usb-1.1, ASIX AX88772B USB 2.0 Ethernet, > 00:50:b6:14:c8:76 > [ 8.912285] usbcore: registered new interface driver asix > [ 9.053373] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot > req 100000Hz, actual 100000HZ div = 124) > [ 9.130886] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot > req 25000000Hz, actual 24800000HZ div = 0) > [ 9.149318] wl18xx_driver wl18xx.3.auto: Direct firmware load for > ti-connectivity/wl18xx-conf.bin failed with error -2 > [ 9.160459] wlcore: ERROR could not get configuration binary > ti-connectivity/wl18xx-conf.bin: -2 > [ 9.169615] wlcore: WARNING falling back to default config > [ 9.214108] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot > req 100000Hz, actual 100000HZ div = 124) > [ 9.294294] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot > req 25000000Hz, actual 24800000HZ div = 0) > [[0;32m OK [0m] Listening on Load/Save RF Kill Switch Status > /dev/rfkill Watch. > [[0;32m OK [0m] Reached target Sockets. > [[0;32m OK [0m] Reached target Basic System. > Starting Entropy Daemon based on the HAVEGE algorithm... > [[0;32m OK [0m] Started TEE Supplicant. > [ 9.514713] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) > [ 9.526319] wlcore: WARNING Detected unconfigured mac address in > nvs, derive from fuse instead. > [ 9.535454] wlcore: WARNING This default nvs file can be removed > from the file system > > and when it passes that stage I can't find wlcore nor wl18xx_driver. > However, I can see > wl1271_sdio failing instead. See [2] > > [ 8.435849] Bluetooth: HCI UART protocol Broadcom registered > [ 8.439669] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot > req 200000Hz, actual 200000HZ div = 62) > [[0;32m OK [0m] Started dnf-automatic-download timer. > [ 8.469492] wl1271_sdio: probe of mmc2:0001:2 failed with error -16 > [[0;32m OK [0m] Started Daily Cleanup of Temporary Directories. > [[0;32m OK [0m] Started dnf-automatic-install timer. > [ 8.525443] Console: switching to colour frame buffer device 256x72 > [ 8.533489] Bluetooth: hci0: change remote baud rate command in firmware > [ 8.584607] kirin-drm f4100000.ade: fb0: DRM emulated frame buffer device > [[0;32m OK [0m] Started dnf-automatic-notifyonly timer. > [[0;32m OK [0m] Listening on R[ 8.614417] [drm] Initialized kirin > 1.0.0 20150718 for f4100000.ade on minor 0 > > and another job that have the similar issue with the previous is [3]: > > [ 8.670110] adv7511 2-0039: 2-0039 supply pvdd not found, using > dummy regulator > [ 8.677908] adv7511 2-0039: 2-0039 supply a2vdd not found, using > dummy regulator > [ 8.685788] adv7511 2-0039: 2-0039 supply v3p3 not found, using > dummy regulator > [ 8.688699] wl1271_sdio: probe of mmc2:0001:1 failed with error -16 > [ 8.690154] Bluetooth: Core ver 2.22 > [ 8.690346] NET: Registered protocol family 31 > [ 8.690355] Bluetooth: HCI device and connection manager > initialized > [ 8.693495] adv7511 2-0039: 2-0039 supply v1p2 not found, using > dummy regulator > [ 8.700240] wl1271_sdio: probe of mmc2:0001:2 failed with error -16 > [ 8.700992] Bluetooth: HCI socket layer initialized > [ 8.701022] Bluetooth: L2CAP socket layer initialized > [ 8.701554] Bluetooth: SCO socket layer initialized > Starting sshd.socket. > [[0;32m OK [0m] Listening on RPCbind Server Activation Socket. > [[0;32m OK [0m] Started Daily rotation of log files. > [ 8.791540] Bluetooth: HCI UART driver ver 2.3 > > > I'm confused why we only see wlcore wl18xx in job [1] and that we see wl1271 > in the other and that we are able to start running tests, even though > I don't think > the jobs where we run tests booted up OK, since we can see > "wl1271_sdio: probe of mmc2:0001:1 failed with error -16". > > Cheers, > Anders > > [1] https://lkft.validation.linaro.org/scheduler/job/543012 > [2] https://lkft.validation.linaro.org/scheduler/job/506683 > [3] https://lkft.validation.linaro.org/scheduler/job/487494
