On Tue, 11 Dec 2018 at 22:51, Ricardo Salveti <rsalveti@xxxxxxxxxxxx> wrote:
>
> On Tue, Dec 11, 2018 at 6:23 PM Ricardo Salveti <rsalveti@xxxxxxxxxxxx> wrote:
> > And now with while true:
> > Dec 11 20:18:13 hikey kernel: wlcore: mac80211 configure filter
> > changed 0 total 80000000
> > Dec 11 20:18:13 hikey kernel: wlcore: waking up chip from elp
> > Dec 11 20:18:13 hikey kernel: wlcore: wakeup time: 8 ms
> > Dec 11 20:18:13 hikey kernel: wlcore: acx group address tbl
> > Dec 11 20:18:13 hikey kernel: wlcore: cmd configure (63)
> > Dec 11 20:18:13 hikey kernel: wlcore: mac80211 remove interface
> > Dec 11 20:18:13 hikey kernel: wlcore: down
> > Dec 11 20:18:13 hikey kernel: wlcore: cmd role disable
> > Dec 11 20:18:13 hikey kernel: wlcore: IRQ work
> > Dec 11 20:18:13 hikey kernel: wlcore: mac80211 stop
> > Dec 11 20:18:13 hikey kernel: wlcore: intr: 0x20 (fw_rx_counter = 0,
> > drv_rx_counter = 0, tx_results_counter = 0)
> > Dec 11 20:18:13 hikey kernel: wlcore: WL1271_ACX_INTR_HW_AVAILABLE
> >
> > Dec 11 20:18:13 hikey kernel: wlcore: mac80211 start
> > Dec 11 20:18:13 hikey kernel: wlcore: mac80211 add interface type 2
> > mac 84:dd:20:92:54:5b
> > Dec 11 20:18:13 hikey kernel: wlcore: allocating hw queue base: 0
> > Dec 11 20:18:13 hikey kernel: wlcore: clock freq 5 (13, 120, 0, 0, spit)
> > Dec 11 20:18:13 hikey kernel: wlcore: chip id 0x6030111
> > Dec 11 20:18:13 hikey kernel: wlcore: firmware chunks to be uploaded: 15
> > Dec 11 20:18:13 hikey kernel: wlcore: chunk 14 addr 0x0 len 120432
> > Dec 11 20:18:13 hikey kernel: wlcore: starting firmware upload
> > Dec 11 20:18:13 hikey kernel: wlcore: fw_data_len 120432 chunk_size 16384
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x000000002d8a6a40 to 0x0
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x0000000048dff62f to 0x4000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000f9372750 to 0x8000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000f2685ee4 to 0xc000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000c4fc484d to 0x10000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000a6d3c9bf to 0x14000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x000000007404dc0f to 0x18000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw last chunk (5744 B)
> > 0x00000000d7beb1f6 to 0x1c000
> > Dec 11 20:18:13 hikey kernel: wlcore: chunk 13 addr 0x100000 len 131072
> > Dec 11 20:18:13 hikey kernel: wlcore: starting firmware upload
> > Dec 11 20:18:13 hikey kernel: wlcore: fw_data_len 131072 chunk_size 16384
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000c3cad69f to 0x100000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000a9e4f338 to 0x104000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x000000003169e0a1 to 0x108000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000cc5b7549 to 0x10c000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x000000009c0bb98a to 0x110000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000f4d0b2c2 to 0x114000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x0000000026e1d203 to 0x118000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000a3905e9c to 0x11c000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw last chunk (0 B)
> > 0x00000000f0c022b6 to 0x120000
> > Dec 11 20:18:13 hikey kernel: wlcore: chunk 12 addr 0x20400000 len 52600
> > Dec 11 20:18:13 hikey kernel: wlcore: starting firmware upload
> > Dec 11 20:18:13 hikey kernel: wlcore: fw_data_len 52600 chunk_size 16384
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x000000004f52801e to 0x20400000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x0000000066503358 to 0x20404000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000433fff1b to 0x20408000
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw last chunk (3448 B)
> > 0x00000000a38c9bd9 to 0x2040c000
> > Dec 11 20:18:13 hikey kernel: wlcore: chunk 11 addr 0xb00000 len 536
> > Dec 11 20:18:13 hikey kernel: wlcore: starting firmware upload
> > Dec 11 20:18:13 hikey kernel: wlcore: fw_data_len 536 chunk_size 16384
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw last chunk (536 B)
> > 0x00000000ced82f93 to 0xb00000
> > Dec 11 20:18:13 hikey kernel: wlcore: chunk 10 addr 0xb0ae40 len 28120
> > Dec 11 20:18:13 hikey kernel: wlcore: starting firmware upload
> > Dec 11 20:18:13 hikey kernel: wlcore: fw_data_len 28120 chunk_size 16384
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x00000000d6832925 to 0xb0ae40
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw last chunk (11736
> > B) 0x0000000037ae96d5 to 0xb0ee40
> > Dec 11 20:18:13 hikey kernel: wlcore: chunk 9 addr 0x80900000 len 61140
> > Dec 11 20:18:13 hikey kernel: wlcore: starting firmware upload
> > Dec 11 20:18:13 hikey kernel: wlcore: fw_data_len 61140 chunk_size 16384
> > Dec 11 20:18:13 hikey kernel: wlcore: uploading fw chunk
> > 0x0000000096b9ba67 to 0x80900000 -------> hangs
> >
> > See the missing 'mmc_host mmc2' messages, which probably indicates
> > that mmc_host wasn't properly set after the down/up sequence, causing
> > the hang when uploading the firmware.
>
> Tried to change back wl12xx_sdio_power_off to use pm_runtime_put_sync
> as a test, and noticed I always get -EBUSY when reproducing the hang,
> so it looks like this could be a race between pm_runtime_put/get when
> doing if down/up (and the side effect on the mmc controller).
I have different serious, one when our board hangs on udhcpc [1], then I see
wlcore and wl18xx_driver.
[ 8.824419] cfg80211: Loading compiled-in X.509 certificates for
regulatory database
[ 8.852546] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 8.861006] platform regulatory.0: Direct firmware load for
regulatory.db failed with error -2
[ 8.870248] cfg80211: failed to load regulatory.db
[ 8.895501] asix 1-1.1:1.0 eth0: register 'asix' at
usb-f72c0000.usb-1.1, ASIX AX88772B USB 2.0 Ethernet,
00:50:b6:14:c8:76
[ 8.912285] usbcore: registered new interface driver asix
[ 9.053373] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot
req 100000Hz, actual 100000HZ div = 124)
[ 9.130886] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot
req 25000000Hz, actual 24800000HZ div = 0)
[ 9.149318] wl18xx_driver wl18xx.3.auto: Direct firmware load for
ti-connectivity/wl18xx-conf.bin failed with error -2
[ 9.160459] wlcore: ERROR could not get configuration binary
ti-connectivity/wl18xx-conf.bin: -2
[ 9.169615] wlcore: WARNING falling back to default config
[ 9.214108] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot
req 100000Hz, actual 100000HZ div = 124)
[ 9.294294] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot
req 25000000Hz, actual 24800000HZ div = 0)
[[0;32m OK [0m] Listening on Load/Save RF Kill Switch Status
/dev/rfkill Watch.
[[0;32m OK [0m] Reached target Sockets.
[[0;32m OK [0m] Reached target Basic System.
Starting Entropy Daemon based on the HAVEGE algorithm...
[[0;32m OK [0m] Started TEE Supplicant.
[ 9.514713] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[ 9.526319] wlcore: WARNING Detected unconfigured mac address in
nvs, derive from fuse instead.
[ 9.535454] wlcore: WARNING This default nvs file can be removed
from the file system
and when it passes that stage I can't find wlcore nor wl18xx_driver.
However, I can see
wl1271_sdio failing instead. See [2]
[ 8.435849] Bluetooth: HCI UART protocol Broadcom registered
[ 8.439669] mmc_host mmc2: Bus speed (slot 0) = 24800000Hz (slot
req 200000Hz, actual 200000HZ div = 62)
[[0;32m OK [0m] Started dnf-automatic-download timer.
[ 8.469492] wl1271_sdio: probe of mmc2:0001:2 failed with error -16
[[0;32m OK [0m] Started Daily Cleanup of Temporary Directories.
[[0;32m OK [0m] Started dnf-automatic-install timer.
[ 8.525443] Console: switching to colour frame buffer device 256x72
[ 8.533489] Bluetooth: hci0: change remote baud rate command in firmware
[ 8.584607] kirin-drm f4100000.ade: fb0: DRM emulated frame buffer device
[[0;32m OK [0m] Started dnf-automatic-notifyonly timer.
[[0;32m OK [0m] Listening on R[ 8.614417] [drm] Initialized kirin
1.0.0 20150718 for f4100000.ade on minor 0
and another job that have the similar issue with the previous is [3]:
[ 8.670110] adv7511 2-0039: 2-0039 supply pvdd not found, using
dummy regulator
[ 8.677908] adv7511 2-0039: 2-0039 supply a2vdd not found, using
dummy regulator
[ 8.685788] adv7511 2-0039: 2-0039 supply v3p3 not found, using
dummy regulator
[ 8.688699] wl1271_sdio: probe of mmc2:0001:1 failed with error -16
[ 8.690154] Bluetooth: Core ver 2.22
[ 8.690346] NET: Registered protocol family 31
[ 8.690355] Bluetooth: HCI device and connection manager
initialized
[ 8.693495] adv7511 2-0039: 2-0039 supply v1p2 not found, using
dummy regulator
[ 8.700240] wl1271_sdio: probe of mmc2:0001:2 failed with error -16
[ 8.700992] Bluetooth: HCI socket layer initialized
[ 8.701022] Bluetooth: L2CAP socket layer initialized
[ 8.701554] Bluetooth: SCO socket layer initialized
Starting sshd.socket.
[[0;32m OK [0m] Listening on RPCbind Server Activation Socket.
[[0;32m OK [0m] Started Daily rotation of log files.
[ 8.791540] Bluetooth: HCI UART driver ver 2.3
I'm confused why we only see wlcore wl18xx in job [1] and that we see wl1271
in the other and that we are able to start running tests, even though
I don't think
the jobs where we run tests booted up OK, since we can see
"wl1271_sdio: probe of mmc2:0001:1 failed with error -16".
Cheers,
Anders
[1] https://lkft.validation.linaro.org/scheduler/job/543012
[2] https://lkft.validation.linaro.org/scheduler/job/506683
[3] https://lkft.validation.linaro.org/scheduler/job/487494
