Hi, > Stefan Wahren <stefan.wahren@xxxxxxxx> hat am 26. November 2018 um 19:14 geschrieben: > > > Hi Arend, > > > Arend van Spriel <arend.vanspriel@xxxxxxxxxxxx> hat am 26. November 2018 um 11:11 geschrieben: > > > > So no AP listed here. I suspect Rafał was focusing on "device_ap_sme=1 > > use_monitor=1" scenario. You can try adding AP entry with similar rx > > bits as P2P_GO above. > > thanks this make all driver errors like "setting AP mode failed -52" disappear, but now hostapd 2.6 seems to stuck in a loop during establishing the link: > i increased the debug level of brcmfmac to 0x5 and i'm getting this while booting: [ 5.288806] brcmfmac: F1 signature read @0x18000000=0x15264345 [ 5.289167] brcmfmac: brcmf_chip_recognition found AXI chip: BCM4345/6 [ 5.293319] brcmfmac: brcmf_chip_cores_check [1 ] core 0x800:51 base 0x18000000 wrap 0x18100000 [ 5.293333] brcmfmac: brcmf_chip_cores_check [2 ] core 0x812:54 base 0x18001000 wrap 0x18101000 [ 5.293344] brcmfmac: brcmf_chip_cores_check [3 ] core 0x83e:9 base 0x18002000 wrap 0x18102000 [ 5.293353] brcmfmac: brcmf_chip_cores_check [4 ] core 0x83c:14 base 0x18003000 wrap 0x18103000 [ 5.293362] brcmfmac: brcmf_chip_cores_check [5 ] core 0x829:21 base 0x18004000 wrap 0x18104000 [ 5.293371] brcmfmac: brcmf_chip_cores_check [6 ] core 0x135:0 base 0x00000000 wrap 0x18107000 [ 5.293379] brcmfmac: brcmf_chip_cores_check [7 ] core 0x240:0 base 0x00000000 wrap 0x00000000 [ 5.295574] brcmfmac: brcmf_chip_get_raminfo RAM: base=0x198000 size=819200 (0xc8000) sr=0 (0x0) [ 5.295686] brcmfmac: brcmf_chip_setup ccrev=51, pmurev=27, pmucaps=0x39d05f1b [ 5.295698] brcmfmac: brcmf_get_module_param Enter, bus=0, chip=17221, rev=6 [ 5.295765] brcmfmac: brcmf_sdio_drivestrengthinit No SDIO driver strength init needed for chip BCM4345/6 rev 6 pmurev 27 [ 5.296204] brcmfmac: brcmf_sdio_probe completed!! [ 5.296219] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 5.413840] brcmfmac: brcmf_sdio_verifymemory Compare RAM dl & ul at 0x00198000; size=600487 [ 5.442090] random: crng init done [ 5.442105] random: 7 urandom warning(s) missed due to ratelimiting [ 5.539438] brcmfmac: brcmf_sdio_verifymemory Compare RAM dl & ul at 0x0025f940; size=1728 [ 5.636378] brcmfmac: brcmf_sdio_firmware_callback enable F2: err=0 [ 5.636577] brcmfmac: brcmf_bus_change_state ignoring transition, bus not attached yet [ 5.636819] brcmfmac: brcmf_add_if allocate netdev interface [ 5.637199] brcmfmac: brcmf_sdio_readshared sdpcm_shared address 0x001FF350 [ 5.638014] brcmfmac: brcmf_sdio_readshared sdpcm_shared address 0x001FF350 [ 5.641788] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ 5.665557] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04 [ 5.666203] brcmfmac: brcmf_c_preinit_dcmds CLM version = API: 12.2 Data: 9.10.105 Compiler: 1.29.4 ClmImport: 1.36.3 Creation: 2018-03-09 18:56:28 [ 5.673860] brcmfmac: brcmf_feat_firmware_capabilities [ ap sta wme 802.11d 802.11h rm cqa cac dualband ampdu ampdu_tx ampdu_rx amsdurx tdls radio_pwrsave btamp p2p proptxstatus mchan p2po anqpo vht-prop-rates dfrts txpwrcache stbc-tx stbc-rx-1ss epno pfnx wnm bsstrans mfp ] [ 5.673890] brcmfmac: brcmf_feat_firmware_capabilities enabling feature: MCHAN [ 5.673899] brcmfmac: brcmf_feat_firmware_capabilities enabling feature: P2P [ 5.674522] brcmfmac: brcmf_feat_iovar_int_get enabling feature: PNO [ 5.675854] brcmfmac: brcmf_feat_iovar_int_get enabling feature: TDLS [ 5.676955] brcmfmac: brcmf_feat_iovar_int_get enabling feature: MFP [ 5.678014] brcmfmac: brcmf_feat_iovar_int_get enabling feature: FWSUP [ 5.678066] brcmfmac: brcmf_fws_attach FWS queueing will be avoided [ 5.678920] brcmfmac: brcmf_cfg80211_attach Registering custom regulatory [ 5.681508] brcmfmac: brcmf_setup_wiphybands nmode=1, vhtmode=1, bw_cap=(1, 7) [ 5.684720] brcmfmac: brcmf_setup_wiphybands nchain=1 [ 5.721118] brcmfmac: check_vif_up device is not ready : status (0) [ 5.721190] brcmfmac: brcmf_net_attach wlan0: Broadcom Dongle Host Driver [ 5.844422] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0252 [ 10.845747] brcmfmac: check_vif_up device is not ready : status (0) [ 11.612740] brcmfmac: check_vif_up device is not ready : status (0) [ 11.613251] brcmfmac: check_vif_up device is not ready : status (0) [ 11.614724] brcmfmac: check_vif_up device is not ready : status (0) [ 11.616385] brcmfmac: check_vif_up device is not ready : status (0) [ 11.637118] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event [ 11.638643] brcmfmac: brcmf_config_dongle power save set to enabled [ 11.639137] brcmfmac: brcmf_dongle_roam Internal Roaming = On [ 11.640504] brcmfmac: brcmf_cfg80211_change_iface IF Type = Infra [ 11.642531] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.642545] brcmfmac: brcmf_cfg80211_set_power_mgmt power save enabled [ 11.767278] brcmfmac: brcmf_p2p_add_vif adding vif "p2p-dev-wlan0" (type=10) [ 11.789469] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event [ 11.791667] brcmfmac: brcmf_add_if allocate non-netdev interface [ 11.792237] brcmfmac: check_vif_up device is not ready : status (0) [ 11.792260] brcmfmac: check_vif_up device is not ready : status (0) [ 11.912572] brcmfmac: check_vif_up device is not ready : status (0) [ 11.913704] brcmfmac: check_vif_up device is not ready : status (0) [ 11.913881] brcmfmac: check_vif_up device is not ready : status (0) [ 11.914027] brcmfmac: check_vif_up device is not ready : status (0) [ 11.915150] brcmfmac: check_vif_up device is not ready : status (0) [ 11.915230] brcmfmac: check_vif_up device is not ready : status (0) [ 14.706985] brcmfmac: brcmf_cfg80211_connect ie (29d9d630), ie_len (28) [ 17.638253] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 19.655039] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 21.780277] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 24.744917] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 24.995983] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 25.246750] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 25.446303] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 26.569338] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 28.692076] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) and this after starting hostapd 2.6: [ 207.921068] brcmfmac: brcmf_btcoex_set_mode DHCP session ends [ 207.921352] brcmfmac: brcmf_cfg80211_change_iface IF Type = AP [ 209.114209] brcmfmac: brcmf_set_mpc MPC : 0 [ 209.143594] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event [ 211.049412] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 213.051521] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 218.084704] brcmfmac: brcmf_escan_timeout: timer expired [ 218.531282] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event [ 218.531776] brcmfmac: brcmf_vif_set_mgmt_ie: vndr ie set error : -52 [ 218.532228] brcmfmac: brcmf_set_mpc MPC : 1 [ 218.533962] brcmfmac: brcmf_cfg80211_change_iface IF Type = Infra [ 218.537955] brcmfmac: brcmf_cfg80211_connect ie (537583ca), ie_len (28) [ 223.410796] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 225.526035] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 227.705830] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 227.956466] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 228.207019] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 228.407567] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 229.521312] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0) [ 231.621031] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
