> On Fri, Nov 09, 2018 at 01:50:51PM +0100, Lorenzo Bianconi wrote:
> > > On 2018-11-09 12:09, Lorenzo Bianconi wrote:
> > > >> Use MT_MAC_APC_BSSID0_H_EN bit to indicatate we are
> > > >> setting BSSID for STA.
> > > >>
> > > >> Signed-off-by: Stanislaw Gruszka <sgruszka@xxxxxxxxxx>
> > > >> ---
> > > >> drivers/net/wireless/mediatek/mt76/mt76x02_mac.c | 12 +++++++++---
> > > >> 1 file changed, 9 insertions(+), 3 deletions(-)
> > > >>
> > > >> diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c b/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
> > > >> index 59b336e34cb5..cfeae5586897 100644
> > > >> --- a/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
> > > >> +++ b/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
> > > >> @@ -826,10 +826,16 @@ void mt76x02_mac_work(struct work_struct *work)
> > > >>
> > > >> void mt76x02_mac_set_bssid(struct mt76x02_dev *dev, u8 idx, const u8 *addr)
> > > >> {
> > > >> + u32 bssid_h = FIELD_PREP(MT_MAC_APC_BSSID_H_ADDR,
> > > >> + get_unaligned_le16(addr + 4));
> > > >> + u32 bssid_l = get_unaligned_le32(addr);
> > > >> +
> > > >> + if (idx > 7)
> > > >> + bssid_h |= MT_MAC_APC_BSSID0_H_EN;
> > > >
> > > > This bit is to enable APClient mode and it is valid just for register 0x1094
> > > > (MT_MAC_APC_BSSID_{L,h}(0)). Moreover IIRC APClient has been disabled because
> > > > it causes a performance degradation.
> > > The performance degradation was with MAC_ADDR_EXT, not AP-Client.
> > > This patch should be fine.
> >
> > Ah, now I remember sorry, you are right :)
> > Anyway IIRC MT_MAC_APC_BSSID0_H_EN is just for AP_CLIENT_BSSID0 (at least for
> > 76x2), for others we need to use BIT(31) but just if APClient is disabled, right?
> > Moreover BSSID filter is currently disabled (BIT(3) in RX_FILTER_CFG).
> >
> > # echo 0x1400 > /sys/kernel/debug/ieee80211/phy0/mt76/regidx
> > # cat /sys/kernel/debug/ieee80211/phy0/mt76/regval
> > 0x00017f97
> >
> > Have you tried to enabled it?
>
> I didn't try this yet, but I think it should be enabled to support
> mulit BSS and MAC address change.
I agree we can use multi-BSS for mac filtering in AP mode but my gut feeling in
STA the hw uses the value in MT_MAC_ADDR_DW{0,1} for unicast packet filtering
(BIT(2) in RX_FILTER_CFG). Moreover I think there is a relation between
MT_MAC_ADDR_DW and BSSID values in multiAP mode.
Regards,
Lorenzo
>
> However I still don't know how to set multiple bssid for STA,
> Use BIT(31) or BIT(16) as indicator or maybe
> just write BSSID to MT_MAC_APC_BSSID_{H,L} and hardware will
> recognize this is not AP BSSID ?
>
> Thanks
> Stanislaw
