On 05/14/2018 08:52 AM, greearb@xxxxxxxxxxxxxxx wrote:
From: Ben Greear <greearb@xxxxxxxxxxxxxxx>
These feature flags are used by ath10k-ct firmware. Add these
so we can use them in future patches and so there are no warnings
about feature flags on loading ath10k-ct firmware.
Hello Kalle,
Any chance you could apply this series? It has been sitting in patchwork in
new state with no feedback for months (last I checked).
I've plenty more patches after this to provide better support for my
firmware, and some of it will probably also be useful for stock firmware.
If I can get these initial patches in, I'll cook up some more and post
them.
Thanks,
Ben
Signed-off-by: Ben Greear <greearb@xxxxxxxxxxxxxxx>
---
v2: Fix warings typo in description.
drivers/net/wireless/ath/ath10k/core.c | 17 +++++++++
drivers/net/wireless/ath/ath10k/core.h | 67 ++++++++++++++++++++++++++++++++++
2 files changed, 84 insertions(+)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 4cf54a7..f2f8f61 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -552,6 +552,23 @@ static const char *const ath10k_core_fw_feature_str[] = {
[ATH10K_FW_FEATURE_NO_PS] = "no-ps",
[ATH10K_FW_FEATURE_MGMT_TX_BY_REF] = "mgmt-tx-by-reference",
[ATH10K_FW_FEATURE_NON_BMI] = "non-bmi",
+ [ATH10K_FW_FEATURE_WMI_10X_CT] = "wmi-10.x-CT",
+ [ATH10K_FW_FEATURE_CT_RXSWCRYPT] = "rxswcrypt-CT",
+ [ATH10K_FW_FEATURE_HAS_TXSTATUS_NOACK] = "txstatus-noack",
+ [ATH10K_FW_FEATURE_CT_RATEMASK] = "ratemask-CT",
+ [ATH10K_FW_FEATURE_HAS_SAFE_BURST] = "safe-burst",
+ [ATH10K_FW_FEATURE_REGDUMP_CT] = "regdump-CT",
+ [ATH10K_FW_FEATURE_TXRATE_CT] = "txrate-CT",
+ [ATH10K_FW_FEATURE_FLUSH_ALL_CT] = "flush-all-CT",
+ [ATH10K_FW_FEATURE_PINGPONG_READ_CT] = "pingpong-CT",
+ [ATH10K_FW_FEATURE_SKIP_CH_RES_CT] = "ch-regs-CT",
+ [ATH10K_FW_FEATURE_NOP_CT] = "nop-CT",
+ [ATH10K_FW_FEATURE_HTT_MGT_CT] = "htt-mgt-CT",
+ [ATH10K_FW_FEATURE_SET_SPECIAL_CT] = "set-special-CT",
+ [ATH10K_FW_FEATURE_NO_BMISS_CT] = "no-bmiss-CT",
+ [ATH10K_FW_FEATURE_HAS_GET_TEMP_CT] = "get-temp-CT",
+ [ATH10K_FW_FEATURE_HAS_TX_RC_CT] = "tx-rc-CT",
+ [ATH10K_FW_FEATURE_CUST_STATS_CT] = "cust-stats-CT",
};
static unsigned int ath10k_core_get_fw_feature_str(char *buf,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index e4ac8f2..c1342c5 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -711,6 +711,73 @@ enum ath10k_fw_features {
/* Firmware load is done externally, not by bmi */
ATH10K_FW_FEATURE_NON_BMI = 19,
+ /* tx-status has the noack bits (CT firmware version 14 and higher ) */
+ ATH10K_FW_FEATURE_HAS_TXSTATUS_NOACK = 30,
+
+ /* Firmware from Candela Technologies, enables more VIFs, etc */
+ ATH10K_FW_FEATURE_WMI_10X_CT = 31,
+
+ /* Firmware from Candela Technologies with rx-software-crypt.
+ * Required for multiple stations connected to same AP when using
+ * encryption (ie, commercial version of CT firmware)
+ */
+ ATH10K_FW_FEATURE_CT_RXSWCRYPT = 32,
+
+ /* Firmware supports extended wmi_common_peer_assoc_complete_cmd that
+ * contains an array of rate-disable masks. This allows the host to
+ * have better control over what rates the firmware will use. CT
+ * Firmware only (v15 and higher)
+ */
+ ATH10K_FW_FEATURE_CT_RATEMASK = 33,
+
+ /* Versions of firmware before approximately 10.2.4.72 would corrupt
+ * txop fields during burst. Since this is fixed now, add a flag to
+ * denote this.
+ */
+ ATH10K_FW_FEATURE_HAS_SAFE_BURST = 34,
+
+ /* Register-dump is supported. */
+ ATH10K_FW_FEATURE_REGDUMP_CT = 35,
+
+ /* TX-Rate is reported. */
+ ATH10K_FW_FEATURE_TXRATE_CT = 36,
+
+ /* Firmware can flush all peers. */
+ ATH10K_FW_FEATURE_FLUSH_ALL_CT = 37,
+
+ /* Firmware can read memory with ping-pong protocol. */
+ ATH10K_FW_FEATURE_PINGPONG_READ_CT = 38,
+
+ /* Firmware can skip channel reservation. */
+ ATH10K_FW_FEATURE_SKIP_CH_RES_CT = 39,
+
+ /* Firmware supports NOP keep-alive message. */
+ ATH10K_FW_FEATURE_NOP_CT = 40,
+
+ /* Firmware supports CT HTT MGT feature. */
+ ATH10K_FW_FEATURE_HTT_MGT_CT = 41,
+
+ /* Set-special cmd-id is supported. */
+ ATH10K_FW_FEATURE_SET_SPECIAL_CT = 42,
+
+ /* SW Beacon Miss is disabled in this kernel, so you have to
+ * let mac80211 manage the connection.
+ */
+ ATH10K_FW_FEATURE_NO_BMISS_CT = 43,
+
+ /* 10.1 firmware that supports getting temperature. Stock
+ * 10.1 cannot.
+ */
+ ATH10K_FW_FEATURE_HAS_GET_TEMP_CT = 44,
+
+ /* Can peer-id be over-ridden to provide rix + retries for raw pkts?
+ * CT only option.
+ */
+ ATH10K_FW_FEATURE_HAS_TX_RC_CT = 45,
+
+ /* Do we support requesting custom stats */
+ ATH10K_FW_FEATURE_CUST_STATS_CT = 46,
+
/* keep last */
ATH10K_FW_FEATURE_COUNT,
};
--
Ben Greear <greearb@xxxxxxxxxxxxxxx>
Candela Technologies Inc http://www.candelatech.com
