On 04/27/2018 11:54 AM, Sebastian Gottschall wrote:
Am 27.04.2018 um 18:07 schrieb Ben Greear:
On 04/26/2018 09:40 PM, Sebastian Gottschall wrote:
Am 26.04.2018 um 22:35 schrieb Ben Greear:
On 04/26/2018 01:21 PM, Sebastian Gottschall wrote:
Am 26.04.2018 um 17:30 schrieb Ben Greear:
On 04/26/2018 02:28 AM, s.gottschall@xxxxxxxxxx wrote:
From: Sebastian Gottschall <s.gottschall@xxxxxxxxxx>
current handling of peer_bw_rxnss_override parameter is based on guessing the VHT160/8080 capability by rx rate. this is wrong and may lead
to a non initialized peer_bw_rxnss_override parameter which is required since VHT160 operation mode only supports 2x2 chainmasks in addition the original
code
initialized the parameter with wrong masked values.
This patch uses the peer phymode and peer nss information for correct initialisation of the peer_bw_rxnss_override parameter.
if this peer information is not available, we initialize the parameter by minimum nss which is suggested by QCA as temporary workaround according
to the QCA sourcecodes.
Signed-off-by: Sebastian Gottschall <s.gottschall@xxxxxxxxxx>
v2: remove debug messages
---
drivers/net/wireless/ath/ath10k/mac.c | 36 +++++++++++++++++++----------------
drivers/net/wireless/ath/ath10k/wmi.c | 4 +---
drivers/net/wireless/ath/ath10k/wmi.h | 14 +++++++++++++-
3 files changed, 34 insertions(+), 20 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 5be6386ede8f..df79af89ee71 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2505,8 +2505,9 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
if (sta->bandwidth == IEEE80211_STA_RX_BW_80)
arg->peer_flags |= ar->wmi.peer_flags->bw80;
- if (sta->bandwidth == IEEE80211_STA_RX_BW_160)
+ if (sta->bandwidth == IEEE80211_STA_RX_BW_160) {
arg->peer_flags |= ar->wmi.peer_flags->bw160;
+ }
/* Calculate peer NSS capability from VHT capabilities if STA
* supports VHT.
@@ -2529,22 +2530,25 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
arg->peer_vht_rates.tx_mcs_set = ath10k_peer_assoc_h_vht_limit(
__le16_to_cpu(vht_cap->vht_mcs.tx_mcs_map), vht_mcs_mask);
- ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x\n",
- sta->addr, arg->peer_max_mpdu, arg->peer_flags);
+ if (arg->peer_num_spatial_streams && (arg->peer_phymode == MODE_11AC_VHT160 || arg->peer_phymode == MODE_11AC_VHT80_80)) {
+ arg->peer_bw_rxnss_override = BW_NSS_FWCONF_160(arg->peer_num_spatial_streams);
+ }
So, an 80Mhz peer could be 4x4 and could connect to a VHT-160 AP. From what I can tell,
the VHT-160 AP can talk 4x4 @ 80Mhz to the peer in this case, but if peer is VHT-160,
then of course it can only talk at 2x2.
So, I don't think you can just look at the peer_num_spatial_streams here.
no? rxnss_override is only taked if peer phymode is vht160 or vht80_80. vht80 is not considered in that code PEER phy_mode, not HOST phy_mode
this parameter is a assoc per peer parameter as far as i can say here.
consider that the firmware will accept anything except 0 for peer_bw_rxnss_override in vht160 operation mode
if a peer is 80 mhz, the code will be skipped here.
From what I can tell, this feature is supposed to configure the rate-ctrl in the firmware to know that
it can only send 1x1 or 2x2 when sending at 160Mhz, but that it can send at higher NSS if it sends
at 80Mhz or lower.
right. but thats exactly what it should does in case that a peer is connecting with vht160 / 80_80
and the peer itself does also send his own nss capabilities which is used if available. if not ,it uses the fallback.
If a 2x2 peer connects to the AP, will it have peer_num_spatial_streams set to 2?
yes. i had some debug code in my initial early versions. the peer does transmit his own nss capabilities.
If so,
then your code will configure the peer_bw_rxnss_override to indicate it can send at 160Mhz
2x2 as well, right? And if so, then that is incorrect.
no. since nss_override is only set if peer phymode is 160 mhz as well
The peer can run at 2x2 80Mhz and 1x1 160Mhz at the same time, so it can advertise
2x2 nss and phy-mode of 160Mhz when associating to the 160Mhz AP, but the peer can only do 1x1 at 160Mhz. There
is no standard way I know of for the peer to tell you specifically that it can only do
1x1 at 160Mhz and also 2x2 at 80Mhz in this case.
per specification the peer is able to provide max nss to the ap. the rx_nss property is calculated
from the mcs rateset provided by the peer by mac80211. this is mcs set provided on on assoc is mandatory.
so there is a way the peer can tell you what it supports and this is what is used.
if a peer does not provide the mcs rateset (which i have seen for a single marvell client)
the fallback mechanism will still work, but just with 1x1. the problem is anything else will crash the firmware.
we have to deal with that.
That is why this rxnns_override exists, to hack around this problem.
i dont think so, because its not just a hack. without providing that parameter the firmware will crash.
so its a always required parameter and not just a hack. for sure the firmware can handle it by itself, just someone
at qca should start to work on it.
but again. my implementation is correct from the information i have out of the qca propertiery wireless driver sources
Your patch is going to break in this case as far as I can tell.
no it isnt. my tests with various different clients from different vendors shows that its working. with 2x2 and 1x1.
its all well detected by the code and configured as expected
consider that this patch fixes a CRASH. accept that. it wont break. it repairs.
I did some testing with the patch below.
The CHAIMASK_ERR is a debug log from FW that I added to help make sure the patch is
acting as desired. The first hex is an identifier, second is the value passed in,
third is phymode, 4th is the tx-chain-mask for 160Mhz frames.
On station side, when associating a 4x4 9984 station to 9984 configured for nss4, 160Mhz, I see:
[86376.620303] ath10k_pci 0000:04:00.0: NIC rx-max-rate: 1560 calculated-max: 1560 rxnss_override: 0x80000009 nss160: 2 spatial-streams: 4
ath10k-fw: ts: 15229 args: 4 RATE_CTRL(19) vid: 255 CHAINMASK_ERR(03) 0x000000af 0x80000009 0x0000000f 0x00000003
On station side, when associating a 4x4 9984 station with chain-mask of 0x3 (2x2) to 9984 configured for nss4, 160Mhz, I see:
[86147.569319] ath10k_pci 0000:04:00.0: NIC rx-max-rate: 1560 calculated-max: 780 rxnss_override: 0x80000000 nss160: 1 spatial-streams: 2
ath10k-fw: ts: 6807 args: 4 RATE_CTRL(19) vid: 255 CHAINMASK_ERR(03) 0x000000af 0x80000000 0x0000000f 0x00000001
On AP side, when associating a 4x4 9984 station to 9984 configured for 160Mhz, I see:
[11167.635324] ath10k_pci 0000:04:00.0: NIC rx-max-rate: 1560 calculated-max: 1560 rxnss_override: 0x80000009 nss160: 2 spatial-streams: 4
ath10k-fw: ts: 72917 args: 4 RATE_CTRL(19) vid: 255 CHAINMASK_ERR(03) 0x000000af 0x80000009 0x0000000f 0x00000003
On AP side, when associating a 4x4 9984 station with chain-mask of 0x3 (2x2) to 9984 configured for nss4, 160Mhz, I see:
[11422.887181] ath10k_pci 0000:04:00.0: NIC rx-max-rate: 1560 calculated-max: 780 rxnss_override: 0x80000000 nss160: 1 spatial-streams: 2
ath10k-fw: ts: 334266 args: 4 RATE_CTRL(19) vid: 255 CHAINMASK_ERR(03) 0x000000af 0x80000000 0x0000000f 0x00000001
On AP side, when associating a 4x4 9984 station configured for 80Mhz instead of 160,
then logging from firmware indicates full 4x4 rates are supported for 80Mhz and below,
and the rxnss_override does not have the (1<<31) bit set:
ath10k-fw: ts: 519211 args: 4 RATE_CTRL(19) vid: 255 CHAINMASK_ERR(03) 0x000000af 0x00000000 0x0000000a 0x00000001
So, I think this might be a better fix for this problem (included inline for discussion,
probably white-space damaged by email client:
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index e1ad983..8bce916 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2860,18 +2860,39 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
arg->peer_vht_rates.rx_max_rate, arg->peer_vht_rates.rx_mcs_set,
arg->peer_vht_rates.tx_max_rate, arg->peer_vht_rates.tx_mcs_set);
- if (arg->peer_vht_rates.rx_max_rate &&
- (sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK)) {
- switch (arg->peer_vht_rates.rx_max_rate) {
+ if (arg->peer_phymode == MODE_11AC_VHT80_80 ||
+ arg->peer_phymode == MODE_11AC_VHT160) {
+ int nss160;
+ int rx = arg->peer_vht_rates.rx_max_rate;
+ /* Deal with cases where chainmask has been decreased.
+ * All known chips that support 160Mhz can do only 1/2 of
+ * the available chains at 160Mhz.
+ */
+ rx = min((int)(arg->peer_num_spatial_streams * 390), rx);
+
+ switch (rx) {
+ /* When a NIC shows up that can do 4x4 at 160Mhz, its
+ * max-rate should be higher, and we can set nss160
+ * to 4 here.
+ */
case 1560:
/* Must be 2x2 at 160Mhz is all it can do. */
- arg->peer_bw_rxnss_override = 2;
+ nss160 = 2;
break;
- case 780:
- /* Can only do 1x1 at 160Mhz (Long Guard Interval) */
- arg->peer_bw_rxnss_override = 1;
+ default:
+ /* Assume we can only do 1x1 at 160Mhz */
+ nss160 = 1;
break;
}
+
+ arg->peer_bw_rxnss_override = ((nss160 - 1) | /* 160Mhz nss */
+ ((nss160 - 1) << 3) | /* 80+80 nss */
+ BIT(PEER_BW_RXNSS_OVERRIDE_OFFSET));
+
+ ath10k_warn(ar, "NIC rx-max-rate: %d calculated-max: %d rxnss_override: 0x%x nss160: %d spatial-streams: %d\n",
+ arg->peer_vht_rates.rx_max_rate, rx,
+ arg->peer_bw_rxnss_override, nss160,
+ arg->peer_num_spatial_streams);
}
}
@@ -3115,9 +3136,9 @@ static int ath10k_peer_assoc_prepare(struct ath10k *ar,
ath10k_peer_assoc_h_crypto(ar, vif, sta, arg);
ath10k_peer_assoc_h_rates(ar, vif, sta, arg);
ath10k_peer_assoc_h_ht(ar, vif, sta, arg);
+ ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
ath10k_peer_assoc_h_vht(ar, vif, sta, arg);
ath10k_peer_assoc_h_qos(ar, vif, sta, arg);
- ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
ath10k_peer_assoc_h_rate_overrides(ar, vif, sta, arg);
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 8eeeab0..365d509 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -7442,12 +7442,8 @@ ath10k_wmi_peer_assoc_fill_10_4(struct ath10k *ar, void *buf,
struct wmi_10_4_peer_assoc_complete_cmd *cmd = buf;
ath10k_wmi_peer_assoc_fill_10_2(ar, buf, arg);
- if (arg->peer_bw_rxnss_override)
- cmd->peer_bw_rxnss_override =
- __cpu_to_le32((arg->peer_bw_rxnss_override - 1) |
- BIT(PEER_BW_RXNSS_OVERRIDE_OFFSET));
- else
- cmd->peer_bw_rxnss_override = 0;
+
+ cmd->peer_bw_rxnss_override = __cpu_to_le32(arg->peer_bw_rxnss_override);
}
static int
Thanks,
Ben
--
Ben Greear <greearb@xxxxxxxxxxxxxxx>
Candela Technologies Inc http://www.candelatech.com
