Search Linux Wireless

Re: Auth Packet TX Delay

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I was able to grab a log with debugging on when the issue started all
the way to when it started timing out association due to TX delay:
https://dl.dropbox.com/u/12121487/delay-messages.gz

On Wed, Jan 16, 2013 at 6:09 PM, Adrian Chadd <adrian@xxxxxxxxxxx> wrote:
> Hm, that register is AR_PHY_RFBUS_GNT, which iirc is only involved in
> fast channel change.
>
> Maybe ath9k's fast channel change code isn't working right, and it's
> not trying a full channel change afterwards?
>
>
>
> Adrian
>
>
> On 15 January 2013 14:06, Robert Shade <robert.shade@xxxxxxxxx> wrote:
>> I'm seeing a periodic issue where the device seems to get stuck in a
>> state where the TX of authentication packets is delayed so that
>> authentication fails.  The log snippet below shows the auth packets
>> getting queued after each "wlan0: send auth to XX", but they're not
>> actually sent until after it gives up and restarts scanning.  Once the
>> device gets into this state, it stays in a SCAN->AUTH->AUTH
>> FAILED->SCAN cycle indefinitely.  However, if I do a ifconfig wlan0
>> down, the device usually recovers and works correctly for a few minutes to
>> hours.
>>
>> This is with the latest compat-drivers.  The authentication is EAP-TLS
>> and it's in an environment where it periodically roams using
>> wpa_supplicant's bgscan.
>>
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc
>> 0x10f eol 0x10f urn 0x0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 1
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc
>> 0x10f eol 0x10f urn 0x0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 2
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc
>> 0x10f eol 0x10f urn 0x0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 3
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc
>> 0x10f eol 0x10f urn 0x0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 4
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 5
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 6
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 7
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 8
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc
>> 0x10f eol 0x10f urn 0x0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 9
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc
>> 0x10f eol 0x10f urn 0x0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ver 64.1 opmode 2 chan 2437 Mhz/0xc0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ah->misc_mode 0x4
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: enabling ADC Gain Calibration
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: enabling ADC DC Calibration
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: enabling IQ Calibration
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: starting ADC Gain Calibration
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable MIB counters
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Restore history: opmode 2
>> chan 2437 Mhz/0xc0 is_scanning=0 ofdm:8 cck:6
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: **** ofdmlevel 8=>8,
>> rssi=67[lo=7 hi=40]
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level
>> 3=>7[def:3] cycpwrThr1[level]=14 ini=6
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level
>> 3=>7[def:3] cycpwrThr1Ext[level]=14 ini=6
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ANI parameters: SI=7,
>> ofdmWS=on FS=2 MRCcck=off listenTime=0 ofdmErrs=0 cckErrs=0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level
>> 2=>6[def:2] firstep[level]=10 ini=2
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level
>> 2=>6[def:2] firstep_low[level]=14 ini=6
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ANI parameters: SI=7,
>> ofdmWS=on FS=6 MRCcck=off listenTime=0 ofdmErrs=0 cckErrs=0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: ofdm weak signal: on=>off
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: ANI parameters: SI=7,
>> ofdmWS=off FS=6 MRCcck=off listenTime=0 ofdmErrs=0 cckErrs=0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: **** ccklevel 6=>6,
>> rssi=67[lo=7 hi=40]
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: New interrupt mask 0xf4040071
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: new IMR 0x918404b0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Do not enable IER ref count -1
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: STA is not yet
>> associated..skipping beacon config
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Beacon already configured
>> for a station interface
>> Nov 20 11:24:33 MR89253 kernel: wlan0: Inserted STA 00:24:6c:74:0a:40
>> Nov 20 11:24:33 MR89253 kernel: wlan0: send auth to 00:24:6c:74:0a:40 (try 1/3)
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: transmitting packet, skb:
>> ffff880137846a80
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: qnum: 0, txq depth: 0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: TXDP[0] = 378480c8 (ffff8800378480c8)
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable TXE on queue: 0
>> Nov 20 11:24:33 MR89253 NetworkManager[1821]: <info> (wlan0):
>> supplicant interface state: scanning -> authenticating
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: RTM_NEWLINK: operstate=0
>> ifi_flags=0x1003 ([UP])
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: RTM_NEWLINK,
>> IFLA_IFNAME: Interface 'wlan0' added
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: if_removed
>> already cleared - ignore event
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Event message available
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: New station
>> 00:24:6c:74:0a:40
>> Nov 20 11:24:33 MR89253 kernel: wlan0: send auth to 00:24:6c:74:0a:40 (try 2/3)
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: transmitting packet, skb:
>> ffff8801265cc2c0
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: qnum: 0, txq depth: 1
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: link[0]
>> (ffff8800378480c8)=37847568 (ffff880037847568)
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable TXE on queue: 0
>> Nov 20 11:24:33 MR89253 kernel: wlan0: send auth to 00:24:6c:74:0a:40 (try 3/3)
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: transmitting packet, skb:
>> ffff8801261aac80
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: qnum: 0, txq depth: 2
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: link[0]
>> (ffff880037847568)=378465f8 (ffff8800378465f8)
>> Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable TXE on queue: 0
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Event message available
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Delete station
>> 00:24:6c:74:0a:40
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Event message available
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: MLME event 37;
>> timeout with 00:24:6c:74:0a:40
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Event
>> AUTH_TIMED_OUT (14) received
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: SME:
>> Authentication timed out
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: Added BSSID
>> 00:24:6c:74:0a:40 into blacklist
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Another BSS in
>> this ESS has been seen; try it next
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: BSSID 00:24:6c:74:0a:40
>> blacklist count incremented to 2
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Setting scan
>> request: 0 sec 100000 usec
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: State:
>> AUTHENTICATING -> DISCONNECTED
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]:
>> wpa_driver_nl80211_set_operstate: operstate 0->0 (DORMANT)
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: netlink: Operstate:
>> linkmode=-1, operstate=5
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: External
>> notification - portEnabled=0
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: Supplicant port
>> status: Unauthorized
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: External
>> notification - portValid=0
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: Supplicant port
>> status: Unauthorized
>> Nov 20 11:24:33 MR89253 kernel: wlan0: authentication with
>> 00:24:6c:74:0a:40 timed out
>> Nov 20 11:24:33 MR89253 kernel: wlan0: Removed STA 00:24:6c:74:0a:40
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: dbus:
>> flush_object_timeout_handler: Timeout - sending changed properties of
>> object /fi/w1/wpa_supplicant1/Interfaces/1
>> Nov 20 11:24:33 MR89253 NetworkManager[1821]: <info> (wlan0):
>> supplicant interface state: authenticating -> disconnected
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: State:
>> DISCONNECTED -> SCANNING
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Starting AP scan
>> for wildcard SSID
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2412 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2417 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2422 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2427 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2432 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2437 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2442 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2447 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2452 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2457 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2462 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2467 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2472 MHz
>> Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2484 MHz
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: AWAKE -> FULL-SLEEP
>> Nov 20 11:24:34 MR89253 kernel: wlan0: Destroyed STA 00:24:6c:74:0a:40
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: FULL-SLEEP -> AWAKE
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: AWAKE -> FULL-SLEEP
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: FULL-SLEEP -> AWAKE
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: Set channel: 2437 MHz type: 0
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF calibrated [ctl] [chain 0] is -50
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF[0] (-50) > MAX (-80),
>> correcting to MAX
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF calibrated [ctl] [chain 1] is -50
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF[1] (-50) > MAX (-80),
>> correcting to MAX
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF calibrated [ctl] [chain 2] is -50
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF[2] (-50) > MAX (-80),
>> correcting to MAX
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: Stopping ANI
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: disable IER
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: Disable MIB counters
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: TX complete: skb: ffff880137846a80
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: TX complete: skb: ffff8801265cc2c0
>> Nov 20 11:24:34 MR89253 kernel: ath: phy0: TX complete: skb: ffff8801261aac80
>>
>> 17:00.0 Network controller: Atheros Communications Inc. AR9160
>> Wireless Network Adapter [AR9001 802.11(a)bgn] (rev 01)
>>         Subsystem: Ubiquiti Networks, Inc. SR71-A 802.11abgn Wireless
>> Mini PCI Adapter
>>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>> Stepping- SERR- FastB2B- DisINTx-
>>         Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>>         Latency: 168, Cache Line Size: 32 bytes
>>         Interrupt: pin A routed to IRQ 18
>>         Region 0: Memory at fd5f0000 (32-bit, non-prefetchable) [size=64K]
>>         Capabilities: [44] Power Management version 2
>>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA
>> PME(D0+,D1-,D2-,D3hot+,D3cold-)
>>                 Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>>         Kernel driver in use: ath9k
>>         Kernel modules: ath9k
>>
>> The last time I saw this on a device that I could debug with, I saw
>> the following in the log just before it entered this state:
>>
>> Jan 15 16:36:53 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:53 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:53 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9c20: 0x00000000 & 0x00000001 != 0x00000001
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Could not kill baseband RX
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9c20: 0x00000000 & 0x00000001 != 0x00000001
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Could not kill baseband RX
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9c20: 0x00000000 & 0x00000001 != 0x00000001
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Could not kill baseband RX
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9c20: 0x00000000 & 0x00000001 != 0x00000001
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: Could not kill baseband RX
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: New scan
>> results available
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Event
>> SCAN_RESULTS (3) received
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Associated on 2412 MHz
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Associated with
>> 00:17:59:2c:c3:20
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Received scan
>> results (45 BSSes)
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Scan results
>> indicate BSS status with 00:17:59:2c:c3:20 as associated
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: New scan results available
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: bgscan simple: scan
>> result notification
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Selecting BSS
>> from priority group 0
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: 0:
>> 00:17:59:2c:c3:20 ssid='l0c0m0t1v3' wpa_ie_len=24 rsn_ie_len=0
>> caps=0xc31 level=-56
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0:    selected based on WPA IE
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0:    selected BSS
>> 00:17:59:2c:c3:20 ssid='l0c0m0t1v3'
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Checking for
>> other virtual interfaces sharing same radio (phy1) in
>> event_scan_results
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: dbus:
>> flush_object_timeout_handler: Timeout - sending changed properties of
>> object /fi/w1/wpa_supplicant1/Interfaces/1
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: RTM_NEWLINK: operstate=1
>> ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: RTM_NEWLINK,
>> IFLA_IFNAME: Interface 'wlan0' added
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: if_removed
>> already cleared - ignore event
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: timeout (100000 us) on reg
>> 0x9860: 0x00048d21 & 0x00000001 != 0x00000000
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to reset channel,
>> reset status -5
>> Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to set channel
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available
>> Jan 15 16:36:56 MR89251 kernel: wlan0: Failed to send nullfunc to AP
>> 00:17:59:2c:c3:20 after 500ms, disconnecting
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Delete station
>> 00:17:59:2c:c3:20
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: MLME event 39
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: MLME event
>> frame - hexdump(len=26): c0 00 00 00 00 17 59 2c c3 20 00 15 6d 84 d7
>> 14 00 17 59 2c c3 20 00 00 04 00
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Deauthenticate event
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Event DEAUTH (12) received
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Deauthentication
>> notification
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0:  * reason 4
>> (locally generated)
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0:  * address
>> 00:17:59:2c:c3:20
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: Deauthentication frame
>> IE(s) - hexdump(len=0): [NULL]
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0:
>> CTRL-EVENT-DISCONNECTED bssid=00:17:59:2c:c3:20 reason=4
>> locally_generated=1
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Auto connect
>> enabled: try to reconnect (wps=0 wpa_state=9)
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Setting scan
>> request: 0 sec 100000 usec
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: Added BSSID
>> 00:17:59:2c:c3:20 into blacklist
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Another BSS in
>> this ESS has been seen; try it next
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: BSSID 00:17:59:2c:c3:20
>> blacklist count incremented to 2
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Not rescheduling
>> scan to ensure that specific SSID scans occur
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Disconnect event
>> - remove keys
>> Jan 15 16:36:56 MR89251 wpa_supplicant[1964]:
>> wpa_driver_nl80211_set_key: ifindex=13 alg=0 addr=(nil) key_idx=0
>> set_tx=0 seq_len=0 key_len=0
>> Jan 15 16:36:56 MR89251 kernel: wlan0: moving STA 00:17:59:2c:c3:20 to state 3
>> Jan 15 16:36:56 MR89251 kernel: wlan0: moving STA 00:17:59:2c:c3:20 to state 2
>> Jan 15 16:36:56 MR89251 kernel: wlan0: moving STA 00:17:59:2c:c3:20 to state 1
>> Jan 15 16:36:56 MR89251 kernel: wlan0: Removed STA 00:17:59:2c:c3:20
>> (goes into associate timeout loop)
>>
>> Please let me know if you need any additional information or testing
>> done.  Thanks.
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Host AP]     [ATH6KL]     [Linux Wireless Personal Area Network]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [Linux Kernel]     [IDE]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Hiking]     [MIPS Linux]     [ARM Linux]     [Linux RAID]

  Powered by Linux