Hm, that register is AR_PHY_RFBUS_GNT, which iirc is only involved in fast channel change. Maybe ath9k's fast channel change code isn't working right, and it's not trying a full channel change afterwards? Adrian On 15 January 2013 14:06, Robert Shade <robert.shade@xxxxxxxxx> wrote: > I'm seeing a periodic issue where the device seems to get stuck in a > state where the TX of authentication packets is delayed so that > authentication fails. The log snippet below shows the auth packets > getting queued after each "wlan0: send auth to XX", but they're not > actually sent until after it gives up and restarts scanning. Once the > device gets into this state, it stays in a SCAN->AUTH->AUTH > FAILED->SCAN cycle indefinitely. However, if I do a ifconfig wlan0 > down, the device usually recovers and works correctly for a few minutes to > hours. > > This is with the latest compat-drivers. The authentication is EAP-TLS > and it's in an environment where it periodically roams using > wpa_supplicant's bgscan. > > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc > 0x10f eol 0x10f urn 0x0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 1 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc > 0x10f eol 0x10f urn 0x0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 2 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc > 0x10f eol 0x10f urn 0x0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 3 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc > 0x10f eol 0x10f urn 0x0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 4 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 5 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 6 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TXQ, inactive queue: 7 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 8 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc > 0x10f eol 0x10f urn 0x0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Reset TX queue: 9 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: tx ok 0x0 err 0x0 desc > 0x10f eol 0x10f urn 0x0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ver 64.1 opmode 2 chan 2437 Mhz/0xc0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ah->misc_mode 0x4 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: enabling ADC Gain Calibration > Nov 20 11:24:33 MR89253 kernel: ath: phy0: enabling ADC DC Calibration > Nov 20 11:24:33 MR89253 kernel: ath: phy0: enabling IQ Calibration > Nov 20 11:24:33 MR89253 kernel: ath: phy0: starting ADC Gain Calibration > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable MIB counters > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Restore history: opmode 2 > chan 2437 Mhz/0xc0 is_scanning=0 ofdm:8 cck:6 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: **** ofdmlevel 8=>8, > rssi=67[lo=7 hi=40] > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level > 3=>7[def:3] cycpwrThr1[level]=14 ini=6 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level > 3=>7[def:3] cycpwrThr1Ext[level]=14 ini=6 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ANI parameters: SI=7, > ofdmWS=on FS=2 MRCcck=off listenTime=0 ofdmErrs=0 cckErrs=0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level > 2=>6[def:2] firstep[level]=10 ini=2 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: level > 2=>6[def:2] firstep_low[level]=14 ini=6 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ANI parameters: SI=7, > ofdmWS=on FS=6 MRCcck=off listenTime=0 ofdmErrs=0 cckErrs=0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ** ch 2437: ofdm weak signal: on=>off > Nov 20 11:24:33 MR89253 kernel: ath: phy0: ANI parameters: SI=7, > ofdmWS=off FS=6 MRCcck=off listenTime=0 ofdmErrs=0 cckErrs=0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: **** ccklevel 6=>6, > rssi=67[lo=7 hi=40] > Nov 20 11:24:33 MR89253 kernel: ath: phy0: New interrupt mask 0xf4040071 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: new IMR 0x918404b0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Do not enable IER ref count -1 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: STA is not yet > associated..skipping beacon config > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Beacon already configured > for a station interface > Nov 20 11:24:33 MR89253 kernel: wlan0: Inserted STA 00:24:6c:74:0a:40 > Nov 20 11:24:33 MR89253 kernel: wlan0: send auth to 00:24:6c:74:0a:40 (try 1/3) > Nov 20 11:24:33 MR89253 kernel: ath: phy0: transmitting packet, skb: > ffff880137846a80 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: qnum: 0, txq depth: 0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: TXDP[0] = 378480c8 (ffff8800378480c8) > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable TXE on queue: 0 > Nov 20 11:24:33 MR89253 NetworkManager[1821]: <info> (wlan0): > supplicant interface state: scanning -> authenticating > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: RTM_NEWLINK: operstate=0 > ifi_flags=0x1003 ([UP]) > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: RTM_NEWLINK, > IFLA_IFNAME: Interface 'wlan0' added > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: if_removed > already cleared - ignore event > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Event message available > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: New station > 00:24:6c:74:0a:40 > Nov 20 11:24:33 MR89253 kernel: wlan0: send auth to 00:24:6c:74:0a:40 (try 2/3) > Nov 20 11:24:33 MR89253 kernel: ath: phy0: transmitting packet, skb: > ffff8801265cc2c0 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: qnum: 0, txq depth: 1 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: link[0] > (ffff8800378480c8)=37847568 (ffff880037847568) > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable TXE on queue: 0 > Nov 20 11:24:33 MR89253 kernel: wlan0: send auth to 00:24:6c:74:0a:40 (try 3/3) > Nov 20 11:24:33 MR89253 kernel: ath: phy0: transmitting packet, skb: > ffff8801261aac80 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: qnum: 0, txq depth: 2 > Nov 20 11:24:33 MR89253 kernel: ath: phy0: link[0] > (ffff880037847568)=378465f8 (ffff8800378465f8) > Nov 20 11:24:33 MR89253 kernel: ath: phy0: Enable TXE on queue: 0 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Event message available > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Delete station > 00:24:6c:74:0a:40 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Event message available > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: MLME event 37; > timeout with 00:24:6c:74:0a:40 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Event > AUTH_TIMED_OUT (14) received > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: SME: > Authentication timed out > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: Added BSSID > 00:24:6c:74:0a:40 into blacklist > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Another BSS in > this ESS has been seen; try it next > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: BSSID 00:24:6c:74:0a:40 > blacklist count incremented to 2 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Setting scan > request: 0 sec 100000 usec > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: State: > AUTHENTICATING -> DISCONNECTED > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: > wpa_driver_nl80211_set_operstate: operstate 0->0 (DORMANT) > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: netlink: Operstate: > linkmode=-1, operstate=5 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: External > notification - portEnabled=0 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: Supplicant port > status: Unauthorized > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: External > notification - portValid=0 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: EAPOL: Supplicant port > status: Unauthorized > Nov 20 11:24:33 MR89253 kernel: wlan0: authentication with > 00:24:6c:74:0a:40 timed out > Nov 20 11:24:33 MR89253 kernel: wlan0: Removed STA 00:24:6c:74:0a:40 > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: dbus: > flush_object_timeout_handler: Timeout - sending changed properties of > object /fi/w1/wpa_supplicant1/Interfaces/1 > Nov 20 11:24:33 MR89253 NetworkManager[1821]: <info> (wlan0): > supplicant interface state: authenticating -> disconnected > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: State: > DISCONNECTED -> SCANNING > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: wlan0: Starting AP scan > for wildcard SSID > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2412 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2417 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2422 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2427 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2432 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2437 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2442 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2447 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2452 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2457 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2462 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2467 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2472 MHz > Nov 20 11:24:33 MR89253 wpa_supplicant[1841]: nl80211: Scan frequency 2484 MHz > Nov 20 11:24:34 MR89253 kernel: ath: phy0: AWAKE -> FULL-SLEEP > Nov 20 11:24:34 MR89253 kernel: wlan0: Destroyed STA 00:24:6c:74:0a:40 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: FULL-SLEEP -> AWAKE > Nov 20 11:24:34 MR89253 kernel: ath: phy0: AWAKE -> FULL-SLEEP > Nov 20 11:24:34 MR89253 kernel: ath: phy0: FULL-SLEEP -> AWAKE > Nov 20 11:24:34 MR89253 kernel: ath: phy0: Set channel: 2437 MHz type: 0 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF calibrated [ctl] [chain 0] is -50 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF[0] (-50) > MAX (-80), > correcting to MAX > Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF calibrated [ctl] [chain 1] is -50 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF[1] (-50) > MAX (-80), > correcting to MAX > Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF calibrated [ctl] [chain 2] is -50 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: NF[2] (-50) > MAX (-80), > correcting to MAX > Nov 20 11:24:34 MR89253 kernel: ath: phy0: Stopping ANI > Nov 20 11:24:34 MR89253 kernel: ath: phy0: disable IER > Nov 20 11:24:34 MR89253 kernel: ath: phy0: Disable MIB counters > Nov 20 11:24:34 MR89253 kernel: ath: phy0: TX complete: skb: ffff880137846a80 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: TX complete: skb: ffff8801265cc2c0 > Nov 20 11:24:34 MR89253 kernel: ath: phy0: TX complete: skb: ffff8801261aac80 > > 17:00.0 Network controller: Atheros Communications Inc. AR9160 > Wireless Network Adapter [AR9001 802.11(a)bgn] (rev 01) > Subsystem: Ubiquiti Networks, Inc. SR71-A 802.11abgn Wireless > Mini PCI Adapter > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 168, Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at fd5f0000 (32-bit, non-prefetchable) [size=64K] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA > PME(D0+,D1-,D2-,D3hot+,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Kernel driver in use: ath9k > Kernel modules: ath9k > > The last time I saw this on a device that I could debug with, I saw > the following in the log just before it entered this state: > > Jan 15 16:36:53 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:53 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:53 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9c20: 0x00000000 & 0x00000001 != 0x00000001 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Could not kill baseband RX > Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9c20: 0x00000000 & 0x00000001 != 0x00000001 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Could not kill baseband RX > Jan 15 16:36:54 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:54 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9c20: 0x00000000 & 0x00000001 != 0x00000001 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Could not kill baseband RX > Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:55 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:55 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:56 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9c20: 0x00000000 & 0x00000001 != 0x00000001 > Jan 15 16:36:56 MR89251 kernel: ath: phy1: Could not kill baseband RX > Jan 15 16:36:56 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: New scan > results available > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Event > SCAN_RESULTS (3) received > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Associated on 2412 MHz > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Associated with > 00:17:59:2c:c3:20 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Received scan > results (45 BSSes) > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Scan results > indicate BSS status with 00:17:59:2c:c3:20 as associated > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: New scan results available > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: bgscan simple: scan > result notification > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Selecting BSS > from priority group 0 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: 0: > 00:17:59:2c:c3:20 ssid='l0c0m0t1v3' wpa_ie_len=24 rsn_ie_len=0 > caps=0xc31 level=-56 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: selected based on WPA IE > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: selected BSS > 00:17:59:2c:c3:20 ssid='l0c0m0t1v3' > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Checking for > other virtual interfaces sharing same radio (phy1) in > event_scan_results > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: dbus: > flush_object_timeout_handler: Timeout - sending changed properties of > object /fi/w1/wpa_supplicant1/Interfaces/1 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: RTM_NEWLINK: operstate=1 > ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: RTM_NEWLINK, > IFLA_IFNAME: Interface 'wlan0' added > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: if_removed > already cleared - ignore event > Jan 15 16:36:56 MR89251 kernel: ath: phy1: timeout (100000 us) on reg > 0x9860: 0x00048d21 & 0x00000001 != 0x00000000 > Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to reset channel, > reset status -5 > Jan 15 16:36:56 MR89251 kernel: ath: phy1: Unable to set channel > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available > Jan 15 16:36:56 MR89251 kernel: wlan0: Failed to send nullfunc to AP > 00:17:59:2c:c3:20 after 500ms, disconnecting > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Delete station > 00:17:59:2c:c3:20 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Event message available > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: MLME event 39 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: MLME event > frame - hexdump(len=26): c0 00 00 00 00 17 59 2c c3 20 00 15 6d 84 d7 > 14 00 17 59 2c c3 20 00 00 04 00 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: nl80211: Deauthenticate event > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Event DEAUTH (12) received > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Deauthentication > notification > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: * reason 4 > (locally generated) > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: * address > 00:17:59:2c:c3:20 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: Deauthentication frame > IE(s) - hexdump(len=0): [NULL] > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: > CTRL-EVENT-DISCONNECTED bssid=00:17:59:2c:c3:20 reason=4 > locally_generated=1 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Auto connect > enabled: try to reconnect (wps=0 wpa_state=9) > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Setting scan > request: 0 sec 100000 usec > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: Added BSSID > 00:17:59:2c:c3:20 into blacklist > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Another BSS in > this ESS has been seen; try it next > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: BSSID 00:17:59:2c:c3:20 > blacklist count incremented to 2 > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Not rescheduling > scan to ensure that specific SSID scans occur > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: wlan0: Disconnect event > - remove keys > Jan 15 16:36:56 MR89251 wpa_supplicant[1964]: > wpa_driver_nl80211_set_key: ifindex=13 alg=0 addr=(nil) key_idx=0 > set_tx=0 seq_len=0 key_len=0 > Jan 15 16:36:56 MR89251 kernel: wlan0: moving STA 00:17:59:2c:c3:20 to state 3 > Jan 15 16:36:56 MR89251 kernel: wlan0: moving STA 00:17:59:2c:c3:20 to state 2 > Jan 15 16:36:56 MR89251 kernel: wlan0: moving STA 00:17:59:2c:c3:20 to state 1 > Jan 15 16:36:56 MR89251 kernel: wlan0: Removed STA 00:17:59:2c:c3:20 > (goes into associate timeout loop) > > Please let me know if you need any additional information or testing > done. Thanks. > -- > To unsubscribe from this list: send the line "unsubscribe linux-wireless" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
