Signed-off-by: Lutz Ballaschke <vegan.grindcore@xxxxxxxxxxxxxx>
---
drivers/watchdog/Kconfig | 4 +-
drivers/watchdog/f71808e_wdt.c | 53 +++++++++++++++++++++++++++++++++++++--
2 files changed, 52 insertions(+), 5 deletions(-)
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index a5ad77e..b259ff8 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -409,11 +409,11 @@ config ALIM7101_WDT
Most people will say N.
config F71808E_WDT
- tristate "Fintek F71808E, F71882FG and F71889FG Watchdog"
+ tristate "Fintek F71808E, F71862FG, F71882FG and F71889FG Watchdog"
depends on X86 && EXPERIMENTAL
help
This is the driver for the hardware watchdog on the Fintek
- F71808E, F71882FG and F71889FG Super I/O controllers.
+ F71808E, F71862FG, F71882FG and F71889FG Super I/O controllers.
You can compile this driver directly into the kernel, or use
it as a module. The module will be called f71808e_wdt.
diff --git a/drivers/watchdog/f71808e_wdt.c b/drivers/watchdog/f71808e_wdt.c
index 65e5796..afec8d8 100644
--- a/drivers/watchdog/f71808e_wdt.c
+++ b/drivers/watchdog/f71808e_wdt.c
@@ -42,6 +42,11 @@
#define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */
#define SIO_REG_DEVREV 0x22 /* Device revision */
#define SIO_REG_MANID 0x23 /* Fintek ID (2 bytes) */
+#define SIO_REG_ROM_ADDR_SEL 0x27 /* ROM address select */
+#define SIO_REG_MFUNCT1 0x29 /* Multi function select 1 */
+#define SIO_REG_MFUNCT2 0x2a /* Multi function select 2 */
+#define SIO_REG_MFUNCT3 0x2b /* Multi function select 3 */
+#define SIO_REG_MFUNCT4 0x2c /* Multi function select 4 */
#define SIO_REG_ENABLE 0x30 /* Logical device enable */
#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */
@@ -70,6 +75,8 @@
#define WATCHDOG_MAX_TIMEOUT (60 * 255)
#define WATCHDOG_PULSE_WIDTH 125 /* 125 ms, default pulse width for
watchdog signal */
+#define WATCHDOG_F71862FG_PIN 63 /* default watchdog reset output
+ pin number 63 */
static unsigned short force_id;
module_param(force_id, ushort, 0);
@@ -89,6 +96,12 @@ MODULE_PARM_DESC(pulse_width,
"Watchdog signal pulse width. 0(=level), 1 ms, 25 ms, 125 ms or 5000 ms"
" (default=" __MODULE_STRING(WATCHDOG_PULSE_WIDTH) ")");
+static unsigned int f71862fg_pin = WATCHDOG_F71862FG_PIN;
+module_param(f71862fg_pin, uint, 0);
+MODULE_PARM_DESC(f71862fg_pin,
+ "Watchdog f71862fg reset output pin configuration. Choose pin 56 or 63"
+ " (default=" __MODULE_STRING(WATCHDOG_F71862FG_PIN)")");
+
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, bool, 0444);
MODULE_PARM_DESC(nowayout, "Disable watchdog shutdown on close");
@@ -282,6 +295,34 @@ exit_unlock:
return err;
}
+/*
+ * f71862fg_pin_configure:
+ * @ioaddr: system I/O-port address to access superio
+ *
+ * The F71862FG chip provides two different pins which can be used
+ * as watchdog reset output. Pin dependent configuration is done here.
+ * NOTE: When ioaddr is non-zero the calling function has to take care of
+ * mutex handling and superio preparation!
+ */
+static int f71862fg_pin_configure(unsigned short ioaddr)
+{
+ if (f71862fg_pin == 63) {
+ if (ioaddr) {
+ /* SPI must be disabled first to use this pin! */
+ superio_clear_bit(ioaddr, SIO_REG_ROM_ADDR_SEL, 6);
+ superio_set_bit(ioaddr, SIO_REG_MFUNCT3, 4);
+ }
+ } else if (f71862fg_pin == 56) {
+ if (ioaddr)
+ superio_set_bit(ioaddr, SIO_REG_MFUNCT1, 1);
+ } else {
+ printk(KERN_ERR DRVNAME ": Invalid argument f71862fg_pin=%d\n",
+ f71862fg_pin);
+ return -EINVAL;
+ }
+ return 0;
+}
+
static int watchdog_start(void)
{
/* Make sure we don't die as soon as the watchdog is enabled below */
@@ -303,6 +344,12 @@ static int watchdog_start(void)
superio_clear_bit(watchdog.sioaddr, 0x2b, 3);
break;
+ case f71862fg:
+ err = f71862fg_pin_configure(watchdog.sioaddr);
+ if (err)
+ goto exit_superio;
+ break;
+
case f71882fg:
/* Set pin 56 to WDTRST# */
superio_set_bit(watchdog.sioaddr, 0x29, 1);
@@ -718,9 +765,9 @@ static int __init f71808e_find(int sioaddr)
watchdog.type = f71889fg;
break;
case SIO_F71862_ID:
- /* These have a watchdog, though it isn't implemented (yet). */
- err = -ENOSYS;
- goto exit;
+ watchdog.type = f71862fg;
+ err = f71862fg_pin_configure(0); /* validate module parameter */
+ break;
case SIO_F71858_ID:
/* Confirmed (by datasheet) not to have a watchdog. */
err = -ENODEV;
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
