On Tue, Nov 17, 2020 at 04:43:42PM +0000, Stefan Hajnoczi wrote:
> On Tue, Nov 17, 2020 at 03:16:20PM +0100, Stefano Garzarella wrote:
> > On Tue, Nov 17, 2020 at 11:11:21AM +0000, Stefan Hajnoczi wrote:
> > > On Fri, Nov 13, 2020 at 02:47:04PM +0100, Stefano Garzarella wrote:
> > > > +static void vdpasim_blk_work(struct work_struct *work)
> > > > +{
> > > > + struct vdpasim *vdpasim = container_of(work, struct vdpasim, work);
> > > > + u8 status = VIRTIO_BLK_S_OK;
> > > > + int i;
> > > > +
> > > > + spin_lock(&vdpasim->lock);
> > > > +
> > > > + if (!(vdpasim->status & VIRTIO_CONFIG_S_DRIVER_OK))
> > > > + goto out;
> > > > +
> > > > + for (i = 0; i < VDPASIM_BLK_VQ_NUM; i++) {
> > > > + struct vdpasim_virtqueue *vq = &vdpasim->vqs[i];
> > > > +
> > > > + if (!vq->ready)
> > > > + continue;
> > > > +
> > > > + while (vringh_getdesc_iotlb(&vq->vring, &vq->iov, &vq->iov,
> > > > + &vq->head, GFP_ATOMIC) > 0) {
> > > > +
> > > > + int write;
> > > > +
> > > > + vq->iov.i = vq->iov.used - 1;
> > > > + write = vringh_iov_push_iotlb(&vq->vring, &vq->iov, &status, 1);
> > > > + if (write <= 0)
> > > > + break;
> > >
> > > We're lucky the guest driver doesn't crash after VIRTIO_BLK_T_GET_ID? :)
> >
> > The crash could happen if the simulator doesn't put the string terminator,
> > but in virtio_blk.c, the serial_show() initialize the buffer putting the
> > string terminator in the VIRTIO_BLK_ID_BYTES element:
> >
> > buf[VIRTIO_BLK_ID_BYTES] = '\0';
> > err = virtblk_get_id(disk, buf);
> >
> > This should prevent the issue, right?
> >
> > However in the last patch of this series I implemented VIRTIO_BLK_T_GET_ID
> > support :-)
>
> Windows, BSD, macOS, etc guest drivers aren't necessarily going to
> terminate or initialize the serial string buffer.
Unfortunately I discovered that VIRTIO_BLK_T_GET_ID is not in the VIRTIO
specs, so, just for curiosity, I checked the QEMU code and I found this:
case VIRTIO_BLK_T_GET_ID:
{
/*
* NB: per existing s/n string convention the string is
* terminated by '\0' only when shorter than buffer.
*/
const char *serial = s->conf.serial ? s->conf.serial : "";
size_t size = MIN(strlen(serial) + 1,
MIN(iov_size(in_iov, in_num),
VIRTIO_BLK_ID_BYTES));
iov_from_buf(in_iov, in_num, 0, serial, size);
virtio_blk_req_complete(req, VIRTIO_BLK_S_OK);
virtio_blk_free_request(req);
break;
}
It seems that the device emulation in QEMU expects that the driver
terminates the serial string buffer.
Do you know why VIRTIO_BLK_T_GET_ID is not in the specs?
Should we add it?
