Hi Peter,
On Wed, 2013-12-04 at 13:37 +0800, Peter Chen wrote:
> On Mon, Nov 11, 2013 at 04:36:09PM +0200, Ivan T. Ivanov wrote:
> >
> > Hi Peter,
> >
> > On Mon, 2013-11-11 at 21:59 +0800, Peter Chen wrote:
> > > On Mon, Nov 11, 2013 at 03:35:37PM +0200, Ivan T. Ivanov wrote:
> > > > From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>
> > > >
> > > > PHY drivers keep track of the current state of the hardware,
> > > > so don't change PHY settings under it.
> > > >
> > > > Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
> > > > ---
> > > > drivers/usb/chipidea/ci_hdrc_msm.c | 9 ++-------
> > > > 1 file changed, 2 insertions(+), 7 deletions(-)
> > > >
> > > > diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
> > > > index e9624f3..338b209 100644
> > > > --- a/drivers/usb/chipidea/ci_hdrc_msm.c
> > > > +++ b/drivers/usb/chipidea/ci_hdrc_msm.c
> > > > @@ -20,13 +20,11 @@
> > > > static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> > > > {
> > > > struct device *dev = ci->gadget.dev.parent;
> > > > - int val;
> > > >
> > > > switch (event) {
> > > > case CI_HDRC_CONTROLLER_RESET_EVENT:
> > > > dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
> > > > - writel(0, USB_AHBBURST);
> > > > - writel(0, USB_AHBMODE);
> > > > + usb_phy_init(ci->transceiver);
> > >
> > > It will reset the PHY, but your comment is "don't change PHY settings under it"
> >
> > :-). This function is exported by PHY drivers, so they will know how
> > to handle this change.
> >
> > >
> > > > break;
> > > > case CI_HDRC_CONTROLLER_STOPPED_EVENT:
> > > > dev_dbg(dev, "CI_HDRC_CONTROLLER_STOPPED_EVENT received\n");
> > > > @@ -34,10 +32,7 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> > > > * Put the transceiver in non-driving mode. Otherwise host
> > > > * may not detect soft-disconnection.
> > > > */
> > > > - val = usb_phy_io_read(ci->transceiver, ULPI_FUNC_CTRL);
> > > > - val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
> > > > - val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
> > > > - usb_phy_io_write(ci->transceiver, val, ULPI_FUNC_CTRL);
> > > > + usb_phy_notify_disconnect(ci->transceiver, USB_SPEED_UNKNOWN);
> > >
> > > Where you have implemented .notify_disconnect?
> > > I have not found it at your phy driver.
> >
> > Yep, I will post PHY driver changes shortly. Meanwhile this should
> > not break existing board file based platforms, because not of them
> > could be compiled (HTC Dream, Halibut Board) and DT based platforms
> > are sill work in progress.
> >
>
> Hi Ivan, I am going to apply this msm chipidea patchset, but the change
> in this file is different with its original meaning.
What did you mean?
CI_HDRC_CONTROLLER_RESET_EVENT -> usb_phy_init()
Take wherever actions are needed to put device in known state. ?
CI_HDRC_CONTROLLER_STOPPED_EVENT -> usb_phy_notify_disconnect()
Emitted after ci->driver->disconnect(&ci->gadget);
Probably I am missing something.
> Have you
> tested at existing platforms?
I have 8074 based DragonBoard which I used for testing.
CV Test Suite engine "Chapter 9 tests" are passing except
"Halt Endpoint Test".
Regards,
Ivan
>
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
