I’ll also mention that I did an strace of “lsusb” later, and noticed that the “Couldn’t open device, …” and “Couldn’t get configuration descriptor 0,…” messages were caused by failure opening /dev/bus/usb/008/003 for reading. [philipp@builder usbutils]$ ls -l /dev/bus/usb/008 total 0 crw-rw-r--. 1 root root 189, 896 Nov 15 15:35 001 crw-rw-r--. 1 root root 189, 897 Nov 15 15:34 002 crw-rw-r--. 1 root root 189, 898 Nov 14 16:30 003 [philipp@builder usbutils]$ cat /dev/bus/usb/008/003 cat: /dev/bus/usb/008/003: No such device [philipp@builder usbutils]$ [philipp@builder usbutils]$ od -x /dev/bus/usb/008/002 0000000 0112 0200 0009 4001 2109 0811 0200 0100 0000020 0100 0209 0019 0101 e000 0932 0004 0100 0000040 0009 0000 0507 0381 0001 000c 0000053 Doing “od -x /dev/busd/usb/009/002” takes a long time to complete… [philipp@builder usbutils]$ od -x /dev/bus/usb/009/002 0000000 0112 0300 0009 0903 2109 0812 8581 0201 0000020 0100 0209 001f 0101 e000 0900 0004 0100 0000040 0009 0000 0507 1381 0002 0608 0030 0200 0000060 0000 0000061 On Nov 15, 2013, at 4:18 PM, Philip Prindeville <philipp_subx@xxxxxxxxxxxxxxxxxxxxx> wrote: > Here’s an excerpt of an email I sent to the manufacturer of the card below. > > They weren’t much help. > > The card doesn’t seem to be working, generates a lot of kernel spew, and doesn’t interact with “lsusb” (from usbtools-006 and -007, tried both). > > Note that lsusb had several issues parsing the /sys files: > > 2 instances of "incomplete hub descriptor, 7 bytes”. > > Also one of the 4 ports on the USB 3.0 hub says: > > " Port 2: 0000.0203 5Gbps power U0 enable connect” > > but all of the others say "Port 4: 0000.02a0 5Gbps power Rx.Detect” (or Port x as appropriate)… not sure why one would be different. Nothing is plugged into any of them, and there should be a total of 7 ports, not 4. > > Also saw "Couldn't open device, some information will be missing” but not sure for what device. > > And saw "Couldn't get configuration descriptor 0, some information will be missing” twice. > > Starting to look like the driver might be part of the issue. > > Anyway, here’s what I wrote. > > ======== > This is what I’m seeing: > > > [philipp@builder ~]$ uname -r > 3.11.7-100.fc18.x86_64 > [philipp@builder ~]$ > [philipp@builder ~]$ sudo lspci -v -v -v > 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge > Subsystem: ASUSTeK Computer Inc. Device 82ee > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [c4] HyperTransport: Slave or Primary Interface > Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL- > Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- > Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- > Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- > Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- > Revision ID: 3.00 > Link Frequency 0: [b] > Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- > Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- > Link Frequency 1: 200MHz > Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- > Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- > Prefetchable memory behind bridge Upper: 00-00 > Bus Number: 00 > Capabilities: [54] HyperTransport: UnitID Clumping > Capabilities: [40] HyperTransport: Retry Mode > Capabilities: [9c] HyperTransport: #1a > Capabilities: [f8] HyperTransport: #1c > > 00:01.0 PCI bridge: ASUSTeK Computer Inc. RS880 PCI to PCI bridge (int gfx) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > I/O behind bridge: 0000b000-0000bfff > Memory behind bridge: fba00000-fbbfffff > Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff > Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+ > Capabilities: [b0] Subsystem: ASUSTeK Computer Inc. Device 82ee > > 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: 0000c000-0000cfff > Memory behind bridge: fbc00000-fbcfffff > Prefetchable memory behind bridge: 00000000f8000000-00000000f9ffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us > ExtTag+ RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- > LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us > ClockPM- Surprise- LLActRep+ BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- > Slot #2, PowerLimit 75.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- > Changed: MRL- PresDet+ LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd- > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- > Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0f00c Data: 4181 > Capabilities: [b0] Subsystem: ASUSTeK Computer Inc. Device 82ee > Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ > Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> > Capabilities: [110 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Kernel driver in use: pcieport > > 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode]) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: fbd00000-fbdfffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us > ExtTag+ RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us > ClockPM- Surprise- LLActRep+ BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+ > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- > Slot #4, PowerLimit 25.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- > Changed: MRL- PresDet+ LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd- > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- > Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0f00c Data: 4191 > Capabilities: [b0] Subsystem: ASUSTeK Computer Inc. Device 82ee > Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ > Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> > Capabilities: [110 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Kernel driver in use: pcieport > > 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: 0000d000-0000dfff > Memory behind bridge: fbe00000-fbefffff > Prefetchable memory behind bridge: 00000000faf00000-00000000faffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us > ExtTag+ RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- > LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us > ClockPM- Surprise- LLActRep+ BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- > Slot #6, PowerLimit 25.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- > Changed: MRL- PresDet+ LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd- > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- > Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0f00c Data: 41a1 > Capabilities: [b0] Subsystem: ASUSTeK Computer Inc. Device 82ee > Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ > Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?> > Capabilities: [110 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Kernel driver in use: pcieport > > 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (prog-if 01 [AHCI 1.0]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 22 > Region 0: I/O ports at a000 [size=8] > Region 1: I/O ports at 9000 [size=4] > Region 2: I/O ports at 8000 [size=8] > Region 3: I/O ports at 7000 [size=4] > Region 4: I/O ports at 6000 [size=16] > Region 5: Memory at fb9ff800 (32-bit, non-prefetchable) [size=1K] > Capabilities: [60] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [70] SATA HBA v1.0 InCfgSpace > Kernel driver in use: ahci > > 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fb9fe000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci-pci > > 00:12.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fb9fd000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci-pci > > 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 17 > Region 0: Memory at fb9ff000 (32-bit, non-prefetchable) [size=256] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Bridge: PM- B3+ > Capabilities: [e4] Debug port: BAR=1 offset=00e0 > Kernel driver in use: ehci-pci > > 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at fb9fc000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci-pci > > 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at fb9fb000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci-pci > > 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 19 > Region 0: Memory at fb9fa800 (32-bit, non-prefetchable) [size=256] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Bridge: PM- B3+ > Capabilities: [e4] Debug port: BAR=1 offset=00e0 > Kernel driver in use: ehci-pci > > 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 3a) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx- > Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ > Kernel driver in use: piix4_smbus > > 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller (prog-if 8a [Master SecP PriP]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 > Interrupt: pin A routed to IRQ 16 > Region 0: I/O ports at 01f0 [size=8] > Region 1: I/O ports at 03f4 > Region 2: I/O ports at 0170 [size=8] > Region 3: I/O ports at 0374 > Region 4: I/O ports at ff00 [size=16] > Capabilities: [70] MSI: Enable- Count=1/2 Maskable- 64bit- > Address: 00000000 Data: 0000 > Kernel driver in use: pata_atiixp > > 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) > Subsystem: ASUSTeK Computer Inc. Device 82ea > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fb9f4000 (64-bit, non-prefetchable) [size=16K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Kernel driver in use: snd_hda_intel > > 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > > 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (prog-if 01 [Subtractive decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=64 > I/O behind bridge: 0000e000-0000efff > Memory behind bridge: fbf00000-fbffffff > Prefetchable memory behind bridge: fff00000-000fffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > > 00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64, Cache Line Size: 64 bytes > Interrupt: pin C routed to IRQ 18 > Region 0: Memory at fb9f9000 (32-bit, non-prefetchable) [size=4K] > Kernel driver in use: ohci-pci > > 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Capabilities: [80] HyperTransport: Host or Secondary Interface > Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- > Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b- > Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- > Revision ID: 3.00 > Link Frequency: [b] > Link Error: <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend- > Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE- > > 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Capabilities: [f0] Secure device <?> > > 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS780C [Radeon HD 3100] (prog-if 00 [VGA controller]) > Subsystem: ASUSTeK Computer Inc. Device 82ee > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M] > Region 1: I/O ports at b000 [size=256] > Region 2: Memory at fbbf0000 (32-bit, non-prefetchable) [size=64K] > Region 5: Memory at fba00000 (32-bit, non-prefetchable) [size=1M] > Expansion ROM at <unassigned> [disabled] > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Kernel driver in use: radeon > > 02:00.0 RAID bus controller: 3ware Inc 9650SE SATA-II RAID PCIe (rev 01) > Subsystem: 3ware Inc 9650SE SATA-II RAID PCIe > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at f8000000 (64-bit, prefetchable) [size=32M] > Region 2: Memory at fbcff000 (64-bit, non-prefetchable) [size=4K] > Region 4: I/O ports at c800 [size=256] > Expansion ROM at fbcc0000 [disabled] [size=128K] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <128ns, L1 <2us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <64us > ClockPM- Surprise- LLActRep+ BwNot- > LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- > Kernel driver in use: 3w-9xxx > > 03:00.0 USB controller: VIA Technologies, Inc. VL80x xHCI USB 3.0 Controller (rev 03) (prog-if 30 [XHCI]) > Subsystem: VIA Technologies, Inc. VL80x xHCI USB 3.0 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 43 > Region 0: Memory at fbdff000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [80] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0400c Data: 41d1 > Capabilities: [c4] Express (v2) Endpoint, MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <16us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM unknown, Latency L0 <2us, L1 <16us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- > DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR-, OBFF Not Supported > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- > Kernel driver in use: xhci_hcd > > 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 02) > Subsystem: ASUSTeK Computer Inc. M3A78-EH Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 44 > Region 0: I/O ports at d800 [size=256] > Region 2: Memory at fbeff000 (64-bit, non-prefetchable) [size=4K] > Region 4: Memory at faff0000 (64-bit, prefetchable) [size=64K] > Expansion ROM at fbec0000 [disabled] [size=128K] > Capabilities: [40] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0100c Data: 41e1 > Capabilities: [70] Express (v1) Endpoint, MSI 01 > DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 4096 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- > Capabilities: [b0] MSI-X: Enable- Count=2 Masked- > Vector table: BAR=4 offset=00000000 > PBA: BAR=4 offset=00000800 > Capabilities: [d0] Vital Product Data > Unknown small resource type 05, will not decode more. > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- > Capabilities: [140 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Capabilities: [160 v1] Device Serial Number 00-00-00-00-ec-10-68-81 > Kernel driver in use: r8169 > > 05:07.0 Serial controller: Perle Systems Ltd Device b008 (prog-if 06 [16950]) > Subsystem: Oxford Semiconductor Ltd Device 9501 > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin A routed to IRQ 21 > Region 0: I/O ports at ec00 [size=32] > Region 1: Memory at fbfff000 (32-bit, non-prefetchable) [size=4K] > Region 2: I/O ports at e880 [size=32] > Region 3: Memory at fbffe000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 1 > Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > > 05:07.1 Bridge: Perle Systems Ltd Device b008 > Subsystem: Oxford Semiconductor Ltd Device 9511 > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at e800 [size=32] > Region 1: Memory at fbffd000 (32-bit, non-prefetchable) [size=4K] > Region 2: I/O ports at e480 [size=32] > Region 3: Memory at fbffc000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 1 > Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > > [philipp@builder ~]$ sudo lsusb -v -v -v > > Bus 001 Device 002: ID 0409:005a NEC Corp. HighSpeed Hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 1 Single TT > bMaxPacketSize0 64 > idVendor 0x0409 NEC Corp. > idProduct 0x005a HighSpeed Hub > bcdDevice 1.00 > iManufacturer 0 > iProduct 0 > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 100mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0001 1x 1 bytes > bInterval 12 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 4 > wHubCharacteristic 0x00a0 > Ganged power switching > Ganged overcurrent protection > TT think time 16 FS bits > Port indicators > bPwrOn2PwrGood 0 * 2 milli seconds > bHubContrCurrent 100 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Port 4: 0000.0303 lowspeed power enable connect > Device Qualifier (for other device speed): > bLength 10 > bDescriptorType 6 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > bNumConfigurations 1 > Device Status: 0x0001 > Self Powered > > Bus 004 Device 002: ID 051d:0002 American Power Conversion Uninterruptible Power Supply > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 8 > idVendor 0x051d American Power Conversion > idProduct 0x0002 Uninterruptible Power Supply > bcdDevice 1.06 > iManufacturer 3 APC > iProduct 1 Back-UPS ES 750 FW:819.z3.D USB FW:z3 > iSerial 2 3B0717X70632 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 34 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 3 Human Interface Device > bInterfaceSubClass 0 No Subclass > bInterfaceProtocol 0 None > iInterface 0 > HID Device Descriptor: > bLength 9 > bDescriptorType 33 > bcdHID 1.10 > bCountryCode 33 US > bNumDescriptors 1 > bDescriptorType 34 Report > wDescriptorLength 872 > Report Descriptors: > ** UNAVAILABLE ** > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0006 1x 6 bytes > bInterval 10 > Device Status: 0x0000 > (Bus Powered) > > Bus 008 Device 002: ID 2109:0811 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 1 Single TT > bMaxPacketSize0 64 > idVendor 0x2109 > idProduct 0x0811 > bcdDevice 2.00 > iManufacturer 0 > iProduct 1 > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 100mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0001 1x 1 bytes > bInterval 12 > incomplete hub descriptor, 7 bytes > Device Status: 0x0001 > Self Powered > > Bus 009 Device 002: ID 2109:0812 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 3.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 3 > bMaxPacketSize0 9 > idVendor 0x2109 > idProduct 0x0812 > bcdDevice 85.81 > iManufacturer 1 > iProduct 2 > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 31 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 19 > Transfer Type Interrupt > Synch Type None > Usage Type Feedback > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 8 > bMaxBurst 0 > incomplete hub descriptor, 7 bytes > Device Status: 0x0001 > Self Powered > > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0002 2.0 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ehci_hcd > iProduct 2 EHCI Host Controller > iSerial 1 0000:00:12.2 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 6 > wHubCharacteristic 0x000a > No power switching (usb 1.0) > Per-port overcurrent protection > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0503 highspeed power enable connect > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Port 4: 0000.0100 power > Port 5: 0000.0100 power > Port 6: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0002 2.0 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ehci_hcd > iProduct 2 EHCI Host Controller > iSerial 1 0000:00:13.2 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 6 > wHubCharacteristic 0x000a > No power switching (usb 1.0) > Per-port overcurrent protection > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Port 4: 0000.0100 power > Port 5: 0000.0100 power > Port 6: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0001 1.1 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ohci_hcd > iProduct 2 OHCI PCI host controller > iSerial 1 0000:00:12.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 3 > wHubCharacteristic 0x0012 > No power switching (usb 1.0) > No overcurrent protection > bPwrOn2PwrGood 2 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0001 1.1 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ohci_hcd > iProduct 2 OHCI PCI host controller > iSerial 1 0000:00:12.1 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 3 > wHubCharacteristic 0x0012 > No power switching (usb 1.0) > No overcurrent protection > bPwrOn2PwrGood 2 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0303 lowspeed power enable connect > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0001 1.1 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ohci_hcd > iProduct 2 OHCI PCI host controller > iSerial 1 0000:00:13.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 3 > wHubCharacteristic 0x0012 > No power switching (usb 1.0) > No overcurrent protection > bPwrOn2PwrGood 2 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0001 1.1 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ohci_hcd > iProduct 2 OHCI PCI host controller > iSerial 1 0000:00:13.1 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 3 > wHubCharacteristic 0x0012 > No power switching (usb 1.0) > No overcurrent protection > bPwrOn2PwrGood 2 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed (or root) hub > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0001 1.1 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 ohci_hcd > iProduct 2 OHCI PCI host controller > iSerial 1 0000:00:14.5 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 2 > wHubCharacteristic 0x0012 > No power switching (usb 1.0) > No overcurrent protection > bPwrOn2PwrGood 2 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Device Status: 0x0001 > Self Powered > > Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 1 Single TT > bMaxPacketSize0 64 > idVendor 0x1d6b Linux Foundation > idProduct 0x0002 2.0 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 xhci_hcd > iProduct 2 xHCI Host Controller > iSerial 1 0000:03:00.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 1 > wHubCharacteristic 0x0009 > Per-port power switching > Per-port overcurrent protection > TT think time 8 FS bits > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x02 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0503 highspeed power enable connect > Device Status: 0x0001 > Self Powered > > Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 3.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 3 > bMaxPacketSize0 9 > idVendor 0x1d6b Linux Foundation > idProduct 0x0003 3.0 root hub > bcdDevice 3.11 > iManufacturer 3 Linux 3.11.7-100.fc18.x86_64 xhci_hcd > iProduct 2 xHCI Host Controller > iSerial 1 0000:03:00.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 31 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed (or root) hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > bMaxBurst 0 > Hub Descriptor: > bLength 12 > bDescriptorType 42 > nNbrPorts 4 > wHubCharacteristic 0x0009 > Per-port power switching > Per-port overcurrent protection > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > bHubDecLat 0.0 micro seconds > wHubDelay 0 nano seconds > DeviceRemovable 0x00 > Hub Port Status: > Port 1: 0000.02a0 5Gbps power Rx.Detect > Port 2: 0000.0203 5Gbps power U0 enable connect > Port 3: 0000.02a0 5Gbps power Rx.Detect > Port 4: 0000.02a0 5Gbps power Rx.Detect > Binary Object Store Descriptor: > bLength 5 > bDescriptorType 15 > wTotalLength 15 > bNumDeviceCaps 1 > SuperSpeed USB Device Capability: > bLength 10 > bDescriptorType 16 > bDevCapabilityType 3 > bmAttributes 0x02 > Latency Tolerance Messages (LTM) Supported > wSpeedsSupported 0x0008 > Device can operate at SuperSpeed (5Gbps) > bFunctionalitySupport 3 > Lowest fully-functional device speed is SuperSpeed (5Gbps) > bU1DevExitLat 4 micro seconds > bU2DevExitLat 231 micro seconds > Device Status: 0x0001 > Self Powered > > Bus 001 Device 004: ID 045e:00db Microsoft Corp. Natural Ergonomic Keyboard 4000 V1.0 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 8 > idVendor 0x045e Microsoft Corp. > idProduct 0x00db Natural Ergonomic Keyboard 4000 V1.0 > bcdDevice 1.73 > iManufacturer 1 Microsoft > iProduct 2 Natural? Ergonomic Keyboard 4000 > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 84 > bNumInterfaces 3 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xa0 > (Bus Powered) > Remote Wakeup > MaxPower 100mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 3 Human Interface Device > bInterfaceSubClass 1 Boot Interface Subclass > bInterfaceProtocol 1 Keyboard > iInterface 0 > HID Device Descriptor: > bLength 9 > bDescriptorType 33 > bcdHID 1.11 > bCountryCode 0 Not supported > bNumDescriptors 1 > bDescriptorType 34 Report > wDescriptorLength 60 > Report Descriptors: > ** UNAVAILABLE ** > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0008 1x 8 bytes > bInterval 10 > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 1 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 3 Human Interface Device > bInterfaceSubClass 0 No Subclass > bInterfaceProtocol 0 None > iInterface 0 > HID Device Descriptor: > bLength 9 > bDescriptorType 33 > bcdHID 1.11 > bCountryCode 0 Not supported > bNumDescriptors 1 > bDescriptorType 34 Report > wDescriptorLength 86 > Report Descriptors: > ** UNAVAILABLE ** > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0008 1x 8 bytes > bInterval 10 > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 2 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 3 Human Interface Device > bInterfaceSubClass 1 Boot Interface Subclass > bInterfaceProtocol 2 Mouse > iInterface 0 > HID Device Descriptor: > bLength 9 > bDescriptorType 33 > bcdHID 1.10 > bCountryCode 0 Not supported > bNumDescriptors 1 > bDescriptorType 34 Report > wDescriptorLength 52 > Report Descriptors: > ** UNAVAILABLE ** > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0008 1x 8 bytes > bInterval 5 > Device Status: 0x0001 > Self Powered > > Bus 008 Device 003: ID 2109:2812 > Couldn't open device, some information will be missing > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 1 Single TT > bMaxPacketSize0 64 > idVendor 0x2109 > idProduct 0x2812 > bcdDevice 85.80 > iManufacturer 0 > iProduct 1 > iSerial 0 > bNumConfigurations 1 > Couldn't get configuration descriptor 0, some information will be missing > Couldn't get configuration descriptor 0, some information will be missing > > > [philipp@builder ~]$ lsmod > Module Size Used by > fuse 86828 3 > ip6t_REJECT 12939 2 > nf_conntrack_ipv6 18782 11 > nf_conntrack_netbios_ns 12665 0 > nf_defrag_ipv6 34589 1 nf_conntrack_ipv6 > hwmon_vid 12688 0 > nf_conntrack_broadcast 12527 1 nf_conntrack_netbios_ns > nf_conntrack_ipv4 14808 11 > nf_defrag_ipv4 12673 1 nf_conntrack_ipv4 > ip6table_filter 12815 1 > xt_conntrack 12760 22 > nf_conntrack 86492 5 nf_conntrack_netbios_ns,xt_conntrack,nf_conntrack_broadcast,nf_conntrack_ipv4,nf_conntrack_ipv6 > ip6_tables 26808 1 ip6table_filter > acpi_cpufreq 19790 1 > kvm 429349 0 > sp5100_tco 13979 0 > shpchp 37032 0 > snd_hda_codec_via 31956 1 > i2c_piix4 22106 0 > snd_hda_intel 44059 3 > snd_hda_codec 183113 2 snd_hda_codec_via,snd_hda_intel > edac_core 56601 0 > edac_mce_amd 22349 0 > snd_hwdep 17650 1 snd_hda_codec > snd_seq 64876 0 > snd_seq_device 14136 1 snd_seq > snd_pcm 98004 2 snd_hda_codec,snd_hda_intel > snd_page_alloc 18268 2 snd_pcm,snd_hda_intel > snd_timer 28690 2 snd_pcm,snd_seq > nfsd 284206 13 > snd 75258 14 snd_hwdep,snd_timer,snd_hda_codec_via,snd_pcm,snd_seq,snd_hda_codec,snd_hda_intel,snd_seq_device > auth_rpcgss 58263 1 nfsd > soundcore 14491 1 snd > microcode 23572 0 > serio_raw 13413 0 > uinput 17614 0 > nfs_acl 12741 1 nfsd > asus_atk0110 18657 0 > k10temp 13126 0 > lockd 93660 1 nfsd > mperf 12607 1 acpi_cpufreq > radeon 1247693 3 > ata_generic 12910 0 > pata_acpi 13038 0 > i2c_algo_bit 13257 1 radeon > pata_atiixp 13271 0 > drm_kms_helper 50468 1 radeon > ttm 79817 1 radeon > drm 282584 5 ttm,drm_kms_helper,radeon > r8169 72001 0 > mii 13527 1 r8169 > 3w_9xxx 43090 5 > i2c_core 38420 5 drm,i2c_piix4,drm_kms_helper,i2c_algo_bit,radeon > sunrpc 257224 21 nfsd,auth_rpcgss,lockd,nfs_acl > [philipp@builder ~]$ > > > From boot time: > > > Nov 14 15:15:55 localhost kernel: [ 1.526658] ohci-pci 0000:00:14.5: OHCI PCI host controller > Nov 14 15:15:55 localhost kernel: [ 1.526744] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 > Nov 14 15:15:55 localhost kernel: [ 1.526842] ohci-pci 0000:00:14.5: irq 18, io mem 0xfb9f9000 > Nov 14 15:15:55 localhost kernel: [ 1.581011] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 > Nov 14 15:15:55 localhost kernel: [ 1.581066] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > Nov 14 15:15:55 localhost kernel: [ 1.581136] usb usb7: Product: OHCI PCI host controller > Nov 14 15:15:55 localhost kernel: [ 1.581182] usb usb7: Manufacturer: Linux 3.11.7-100.fc18.x86_64 ohci_hcd > Nov 14 15:15:55 localhost kernel: [ 1.581234] usb usb7: SerialNumber: 0000:00:14.5 > Nov 14 15:15:55 localhost kernel: [ 1.581361] hub 7-0:1.0: USB hub found > Nov 14 15:15:55 localhost kernel: [ 1.581424] hub 7-0:1.0: 2 ports detected > Nov 14 15:15:55 localhost kernel: [ 1.581535] uhci_hcd: USB Universal Host Controller Interface driver > Nov 14 15:15:55 localhost kernel: [ 1.581649] xhci_hcd 0000:03:00.0: xHCI Host Controller > Nov 14 15:15:55 localhost kernel: [ 1.581732] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 8 > Nov 14 15:15:55 localhost kernel: [ 1.582033] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002 > Nov 14 15:15:55 localhost kernel: [ 1.582086] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > Nov 14 15:15:55 localhost kernel: [ 1.582165] usb usb8: Product: xHCI Host Controller > Nov 14 15:15:55 localhost kernel: [ 1.582217] usb usb8: Manufacturer: Linux 3.11.7-100.fc18.x86_64 xhci_hcd > Nov 14 15:15:55 localhost kernel: [ 1.582269] usb usb8: SerialNumber: 0000:03:00.0 > Nov 14 15:15:55 localhost kernel: [ 1.582401] hub 8-0:1.0: USB hub found > Nov 14 15:15:55 localhost kernel: [ 1.582459] hub 8-0:1.0: 1 port detected > Nov 14 15:15:55 localhost kernel: [ 1.582572] xhci_hcd 0000:03:00.0: xHCI Host Controller > Nov 14 15:15:55 localhost kernel: [ 1.582655] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 9 > Nov 14 15:15:55 localhost kernel: [ 1.582744] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003 > Nov 14 15:15:55 localhost kernel: [ 1.582797] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > Nov 14 15:15:55 localhost kernel: [ 1.582861] usb usb9: Product: xHCI Host Controller > Nov 14 15:15:55 localhost kernel: [ 1.582912] usb usb9: Manufacturer: Linux 3.11.7-100.fc18.x86_64 xhci_hcd > Nov 14 15:15:55 localhost kernel: [ 1.582965] usb usb9: SerialNumber: 0000:03:00.0 > Nov 14 15:15:55 localhost kernel: [ 1.583101] hub 9-0:1.0: USB hub found > Nov 14 15:15:55 localhost kernel: [ 1.583161] hub 9-0:1.0: 4 ports detected > Nov 14 15:15:55 localhost kernel: [ 1.589043] usbcore: registered new interface driver usbserial > Nov 14 15:15:55 localhost kernel: [ 1.589095] usbcore: registered new interface driver usbserial_generic > Nov 14 15:15:55 localhost kernel: [ 1.589147] usbserial: USB Serial support registered for generic > > > And in /var/log/messages I see a lot of repetition of: > > Nov 15 11:39:05 localhost kernel: [68800.027215] hub 9-2:1.0: hub_port_status failed (err = -110) > Nov 15 11:39:19 localhost kernel: [68814.028276] hub 9-2:1.0: hub_port_status failed (err = -110) > > > > It looks like the 2nd device is hub 8, but I’m only seeing a single port, and it’s showing up as High Speed only. > > > > On Nov 14, 2013, at 8:19 PM, ORICO Technology Co. Ltd - Amazon Marketplace <htw3t8xfqks7h38@xxxxxxxxxxxxxxxxxxxxxx> wrote: > >> Order ID 110-0033905-7007439: >> 1 of ORICO PVU3-5O2I Booster USB 3.0 7 Port PCI Express Card (5 Rear USB3.0 Ports and Internal USB3.0 20PIN Connector) with VL800 and VL812 Controller [ASIN: B008716XNM] >> >> ------------- Begin message ------------- >> >> Dear Philip, >> >> Good Day! >> I sincerely sorry for this issue from ORICO happen to you. >> ORICO PVU3-5O2I support Linux and Compatible with Various Linux Kernels with Nature Driver. >> ORICO Booster USB 3.0 PCI Express Card Compatible with Any Windows or Linux Desktop Computer with Available PCI Express x1,x2,x4, x8 or x16 Slot and Can't Fit in PCI Slot . >> Please kindly advise me if you are connect with all of the port in the same time or check with the each port to know only 4 of the 7 ports are visible ? >> >> I looking forwards to hear from you. >> >> Have a nice day ahead. >> >> >> Best Regards >> Mandy >> >> --- Original message --- >> >> As it turns out, the card is not supported by Linux, and indeed only 4 of the 7 ports are visible. >> >> I'll be returning it as incompatible. >> >> >> On 11/13/2013 07:49 PM, ORICO Technology Co. Ltd - Amazon Marketplace wrote: >>> Order ID 110-0033905-7007439: >>> 1 of ORICO PVU3-5O2I Booster USB 3.0 7 Port PCI Express Card (5 Rear USB3.0 Ports and Internal USB3.0 20PIN Connector) with VL800 and VL812 Controller [ASIN: B008716XNM] >>> >>> ------------- Begin message ------------- >>> >>> Dear Philip, >>> >>> Thank you so much for your soon reply. >>> We will send email to all of customer if they buy ORICO PCI-E card to explain the notes when they install the card. >>> So please feel free to write to us any time if any concerns and we will be here to help. >>> Thank you for choosing ORICO as your preferred choice. >>> >>> Have a wonderful day ahead. >>> >>> >>> Best Regards >>> Mandy >>> >>> --- Original message --- >>> >>> Um… I’m not a Windows users. I’m running Linux 3.11.8. >>> >>> Also I don’t remember submitting any feedback, so why exactly am I getting this? >>> >>> >>> >>> On Nov 13, 2013, at 6:32 PM, ORICO Technology Co. Ltd - Amazon Marketplace <[e-mail address removed]> wrote: >>> >>>> Order ID 110-0033905-7007439: >>>> 1 of ORICO PVU3-5O2I Booster USB 3.0 7 Port PCI Express Card (5 Rear USB3.0 Ports and Internal USB3.0 20PIN Connector) with VL800 and VL812 Controller [ASIN: B008716XNM] >>>> >>>> ------------- Begin message ------------- >>>> >>>> Dear Philip, >>>> >>>> >>>> Thank you for choosing ORICO as your preferred choice.This is Mandy from ORICO Customer Care Team. >>>> >>>> >>>> The USB3.0 card you ordered Achieved with VLI USB3.0 Controller from Via-Labs, Compatible Windows XP or Later and Linux.No Additionally Driver and Application is need when installing the Card Under Linux.However Driver is required for Windows OS.Please download and install the driver in Following Link when Autorun Installation Failed. >>>> https://www.box.com/s/7jyb11ksz9jafj3bo4oe >>>> >>>> >>>> Please Note:This Item requires 4PIN power supply to power it.Please make sure you have attached the power supply. >>>> >>>> >>>> We Sincerely hope that you will be pleased with the product and services rendered. >>>> If there is any issues please feel free to leave message for us or mail to us. >>>> >>>> >>>> Once you had use the product , we will like to appeal your kind assistance in posting a Product Review so that >>>> others can also benefit from your experience .In this fast pace society , we understand that how scare time can >>>> be and we deeply appreciate your valuable time and input. >>>> >>>> In ORICO , We believe in going The Extra Miles and hope to hear from you soon. >>>> >>>> Best Regards >>>> ORICO Customer Care Team >>>> >>> >>> >>> >>> >>> >> >> >> >> >> >> >> >> ------------- End message ------------- >> >> For Your Information: To help arbitrate disputes and preserve trust and safety, we retain all messages buyers and sellers send through Amazon.com for two years. This includes your response to the message above. Amazon.com uses filtering technology to protect buyers and sellers from possible fraud. Messages that fail this filtering will not be transmitted. >> >> We want you to buy with confidence anytime you purchase products on Amazon.com. Learn more about Safe Online Shopping (http://www.amazon.com/gp/help/customer/display.html?nodeId=551434) and our safe buying guarantee (http://www.amazon.com/gp/help/customer/display.html?nodeId=537868). >> >> >> >> [commMgrTok:A1Z71RJ9N7OG2T] > -- > To unsubscribe from this list: send the line "unsubscribe linux-usb" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
