Hello, Just wanted to check if anyone has this USB controller: Etron Technology, Inc. EJ168 USB 3.0 Host Controller (rev 01) working on linux. Any thoughts on patch you had to use, etc., please? Thanks Joe On Sun, Sep 1, 2013 at 4:14 PM, joe M <joe9mail@xxxxxxxxx> wrote: > Hello, > > I am not able to figure out how to connect a 1.11 usb full speed > device to a USB 3.0 port. > > This is the output in syslog when I rmmod xhci_hcd and modprobe > xhci-hcd: http://codepad.org/8mc0tABX > > These are the messages that seem to be causing the issue: > Sep 1 15:57:03 master kernel: [ 1182.014895] usb 6-1: device not > accepting address 2, error -62 > Sep 1 15:57:03 master kernel: [ 1182.014942] xhci_hcd 0000:03:00.0: > Bad Slot ID 1 > Sep 1 15:57:03 master kernel: [ 1182.014945] xhci_hcd 0000:03:00.0: > Could not allocate xHCI USB device data structures > Sep 1 15:57:03 master kernel: [ 1182.014950] hub 6-0:1.0: couldn't > allocate port 1 usb_device > > When I plug in the USB full speed device, these are the messages: > > Sep 1 16:00:17 master kernel: [ 1376.248867] usb usb6: usb wakeup-resume > Sep 1 16:00:17 master kernel: [ 1376.248875] usb usb6: usb auto-resume > Sep 1 16:00:17 master kernel: [ 1376.248894] hub 6-0:1.0: hub_resume > Sep 1 16:00:17 master kernel: [ 1376.248905] hub 6-0:1.0: port 1: > status 0101 change 0000 > Sep 1 16:00:17 master kernel: [ 1376.248910] hub 6-0:1.0: port 2: > status 0101 change 0001 > Sep 1 16:00:17 master kernel: [ 1376.349888] hub 6-0:1.0: state 7 > ports 2 chg 0006 evt 0000 > Sep 1 16:00:17 master kernel: [ 1376.349898] hub 6-0:1.0: port 1, > status 0101, change 0000, 12 Mb/s > Sep 1 16:00:17 master kernel: [ 1376.451953] usb 6-1: new full-speed > USB device number 3 using xhci_hcd > Sep 1 16:00:22 master kernel: [ 1381.455764] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:27 master kernel: [ 1386.660767] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:27 master kernel: [ 1386.861922] usb 6-1: device not > accepting address 3, error -62 > Sep 1 16:00:27 master kernel: [ 1386.861977] xhci_hcd 0000:03:00.0: > Bad Slot ID 2 > Sep 1 16:00:27 master kernel: [ 1386.861980] xhci_hcd 0000:03:00.0: > Could not allocate xHCI USB device data structures > Sep 1 16:00:27 master kernel: [ 1386.861985] hub 6-0:1.0: couldn't > allocate port 1 usb_device > Sep 1 16:00:27 master kernel: [ 1386.862006] hub 6-0:1.0: port 2, > status 0101, change 0000, 12 Mb/s > Sep 1 16:00:27 master kernel: [ 1386.964011] usb 6-2: new full-speed > USB device number 4 using xhci_hcd > Sep 1 16:00:32 master kernel: [ 1391.967825] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:38 master kernel: [ 1397.172814] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:38 master kernel: [ 1397.373975] usb 6-2: device not > accepting address 4, error -62 > Sep 1 16:00:38 master kernel: [ 1397.374027] xhci_hcd 0000:03:00.0: > Bad Slot ID 3 > Sep 1 16:00:38 master kernel: [ 1397.374030] xhci_hcd 0000:03:00.0: > Could not allocate xHCI USB device data structures > Sep 1 16:00:38 master kernel: [ 1397.374035] hub 6-0:1.0: couldn't > allocate port 2 usb_device > Sep 1 16:00:38 master kernel: [ 1397.374052] hub 6-0:1.0: hub_suspend > Sep 1 16:00:38 master kernel: [ 1397.374077] usb usb6: bus > auto-suspend, wakeup 1 > > With the USB 2.0 hub, I could use usbmon to check out why the device > does not work. Using usbmon on a USB 3.0 hub does not seem to show any > valuable output. I tried both usbmon client and 'cat 6u' (where 6 is > the bus id) to check usbmon output. > > I am the developer for this usb device and the device works fine on a > 1.11 and a 2.0 hub. With the kernel xhci debugging option, there is a > lot of output, I am wondering if there is a usbmon-like debugging > mechanism for xhci. > > Any thoughts, please? > > Thanks > Joe > > Complete syslog message on modprobe xhci-hcd and pluggin in the usb > 1.11 full speed device: > > Sep 1 15:56:33 master kernel: [ 1152.169082] xhci_hcd 0000:03:00.0: > remove, state 4 > Sep 1 15:56:33 master kernel: [ 1152.169087] xhci_hcd 0000:03:00.0: > roothub graceful disconnect > Sep 1 15:56:33 master kernel: [ 1152.169091] usb usb7: USB > disconnect, device number 1 > Sep 1 15:56:33 master kernel: [ 1152.169092] usb usb7: unregistering device > Sep 1 15:56:33 master kernel: [ 1152.169094] usb usb7: unregistering > interface 7-0:1.0 > Sep 1 15:56:33 master kernel: [ 1152.169152] usb usb7: > usb_disable_device nuking all URBs > Sep 1 15:56:33 master kernel: [ 1152.169154] xHCI xhci_drop_endpoint > called for root hub > Sep 1 15:56:33 master kernel: [ 1152.169155] xHCI > xhci_check_bandwidth called for root hub > Sep 1 15:56:33 master kernel: [ 1152.169224] xhci_hcd 0000:03:00.0: > USB bus 7 deregistered > Sep 1 15:56:33 master kernel: [ 1152.169256] xhci_hcd 0000:03:00.0: > remove, state 4 > Sep 1 15:56:33 master kernel: [ 1152.169258] xhci_hcd 0000:03:00.0: > roothub graceful disconnect > Sep 1 15:56:33 master kernel: [ 1152.169260] usb usb6: USB > disconnect, device number 1 > Sep 1 15:56:33 master kernel: [ 1152.169262] usb usb6: unregistering device > Sep 1 15:56:33 master kernel: [ 1152.169263] usb usb6: unregistering > interface 6-0:1.0 > Sep 1 15:56:33 master kernel: [ 1152.169297] usb usb6: > usb_disable_device nuking all URBs > Sep 1 15:56:33 master kernel: [ 1152.169299] xHCI xhci_drop_endpoint > called for root hub > Sep 1 15:56:33 master kernel: [ 1152.169300] xHCI > xhci_check_bandwidth called for root hub > Sep 1 15:56:33 master kernel: [ 1152.169374] xhci_hcd 0000:03:00.0: > USB bus 6 deregistered > Sep 1 15:56:52 master kernel: [ 1171.302259] xhci_hcd 0000:03:00.0: > xHCI Host Controller > Sep 1 15:56:52 master kernel: [ 1171.302426] xhci_hcd 0000:03:00.0: > new USB bus registered, assigned bus number 6 > Sep 1 15:56:52 master kernel: [ 1171.302536] xhci_hcd 0000:03:00.0: > supports USB remote wakeup > Sep 1 15:56:52 master kernel: [ 1171.302572] usb usb6: default language 0x0409 > Sep 1 15:56:52 master kernel: [ 1171.302577] usb usb6: udev 1, busnum > 6, minor = 640 > Sep 1 15:56:52 master kernel: [ 1171.302579] usb usb6: New USB device > found, idVendor=1d6b, idProduct=0002 > Sep 1 15:56:52 master kernel: [ 1171.302581] usb usb6: New USB device > strings: Mfr=3, Product=2, SerialNumber=1 > Sep 1 15:56:52 master kernel: [ 1171.302582] usb usb6: Product: xHCI > Host Controller > Sep 1 15:56:52 master kernel: [ 1171.302584] usb usb6: Manufacturer: > Linux 3.10.10 xhci_hcd > Sep 1 15:56:52 master kernel: [ 1171.302585] usb usb6: SerialNumber: > 0000:03:00.0 > Sep 1 15:56:52 master kernel: [ 1171.302679] usb usb6: usb_probe_device > Sep 1 15:56:52 master kernel: [ 1171.302682] usb usb6: configuration > #1 chosen from 1 choice > Sep 1 15:56:52 master kernel: [ 1171.302684] xHCI xhci_add_endpoint > called for root hub > Sep 1 15:56:52 master kernel: [ 1171.302685] xHCI > xhci_check_bandwidth called for root hub > Sep 1 15:56:52 master kernel: [ 1171.302690] usb usb6: adding 6-0:1.0 > (config #1, interface 0) > Sep 1 15:56:52 master kernel: [ 1171.302725] hub 6-0:1.0: usb_probe_interface > Sep 1 15:56:52 master kernel: [ 1171.302727] hub 6-0:1.0: > usb_probe_interface - got id > Sep 1 15:56:52 master kernel: [ 1171.302729] hub 6-0:1.0: USB hub found > Sep 1 15:56:52 master kernel: [ 1171.302736] hub 6-0:1.0: 2 ports detected > Sep 1 15:56:52 master kernel: [ 1171.302737] hub 6-0:1.0: standalone hub > Sep 1 15:56:52 master kernel: [ 1171.302738] hub 6-0:1.0: individual > port power switching > Sep 1 15:56:52 master kernel: [ 1171.302739] hub 6-0:1.0: individual > port over-current protection > Sep 1 15:56:52 master kernel: [ 1171.302741] hub 6-0:1.0: Single TT > Sep 1 15:56:52 master kernel: [ 1171.302742] hub 6-0:1.0: TT requires > at most 8 FS bit times (666 ns) > Sep 1 15:56:52 master kernel: [ 1171.302744] hub 6-0:1.0: power on to > power good time: 20ms > Sep 1 15:56:52 master kernel: [ 1171.302746] hub 6-0:1.0: local power > source is good > Sep 1 15:56:52 master kernel: [ 1171.302764] hub 6-0:1.0: enabling > power on all ports > Sep 1 15:56:52 master kernel: [ 1171.306685] xhci_hcd 0000:03:00.0: > xHCI Host Controller > Sep 1 15:56:52 master kernel: [ 1171.306726] xhci_hcd 0000:03:00.0: > new USB bus registered, assigned bus number 7 > Sep 1 15:56:52 master kernel: [ 1171.306751] xhci_hcd 0000:03:00.0: > supports USB remote wakeup > Sep 1 15:56:52 master kernel: [ 1171.306788] usb usb7: skipped 1 > descriptor after endpoint > Sep 1 15:56:52 master kernel: [ 1171.306981] usb usb7: default language 0x0409 > Sep 1 15:56:52 master kernel: [ 1171.306986] usb usb7: udev 1, busnum > 7, minor = 768 > Sep 1 15:56:52 master kernel: [ 1171.306988] usb usb7: New USB device > found, idVendor=1d6b, idProduct=0003 > Sep 1 15:56:52 master kernel: [ 1171.306989] usb usb7: New USB device > strings: Mfr=3, Product=2, SerialNumber=1 > Sep 1 15:56:52 master kernel: [ 1171.306991] usb usb7: Product: xHCI > Host Controller > Sep 1 15:56:52 master kernel: [ 1171.306992] usb usb7: Manufacturer: > Linux 3.10.10 xhci_hcd > Sep 1 15:56:52 master kernel: [ 1171.306994] usb usb7: SerialNumber: > 0000:03:00.0 > Sep 1 15:56:52 master kernel: [ 1171.307042] usb usb7: usb_probe_device > Sep 1 15:56:52 master kernel: [ 1171.307044] usb usb7: configuration > #1 chosen from 1 choice > Sep 1 15:56:52 master kernel: [ 1171.307047] xHCI xhci_add_endpoint > called for root hub > Sep 1 15:56:52 master kernel: [ 1171.307048] xHCI > xhci_check_bandwidth called for root hub > Sep 1 15:56:52 master kernel: [ 1171.307052] usb usb7: adding 7-0:1.0 > (config #1, interface 0) > Sep 1 15:56:52 master kernel: [ 1171.307582] hub 7-0:1.0: usb_probe_interface > Sep 1 15:56:52 master kernel: [ 1171.307585] hub 7-0:1.0: > usb_probe_interface - got id > Sep 1 15:56:52 master kernel: [ 1171.307587] hub 7-0:1.0: USB hub found > Sep 1 15:56:52 master kernel: [ 1171.307651] hub 7-0:1.0: 2 ports detected > Sep 1 15:56:52 master kernel: [ 1171.307653] hub 7-0:1.0: standalone hub > Sep 1 15:56:52 master kernel: [ 1171.307654] hub 7-0:1.0: individual > port power switching > Sep 1 15:56:52 master kernel: [ 1171.307655] hub 7-0:1.0: individual > port over-current protection > Sep 1 15:56:52 master kernel: [ 1171.307657] hub 7-0:1.0: TT requires > at most 8 FS bit times (666 ns) > Sep 1 15:56:52 master kernel: [ 1171.307658] hub 7-0:1.0: power on to > power good time: 20ms > Sep 1 15:56:52 master kernel: [ 1171.307661] hub 7-0:1.0: local power > source is good > Sep 1 15:56:52 master kernel: [ 1171.307729] hub 7-0:1.0: enabling > power on all ports > Sep 1 15:56:52 master kernel: [ 1171.402762] hub 6-0:1.0: port 1: > status 0101 change 0001 > Sep 1 15:56:52 master kernel: [ 1171.407863] hub 7-0:1.0: state 7 > ports 2 chg 0000 evt 0000 > Sep 1 15:56:52 master kernel: [ 1171.407892] hub 7-0:1.0: hub_suspend > Sep 1 15:56:52 master kernel: [ 1171.407896] usb usb7: bus > auto-suspend, wakeup 1 > Sep 1 15:56:52 master kernel: [ 1171.502935] hub 6-0:1.0: state 7 > ports 2 chg 0002 evt 0000 > Sep 1 15:56:52 master kernel: [ 1171.502947] hub 6-0:1.0: port 1, > status 0101, change 0000, 12 Mb/s > Sep 1 15:56:52 master kernel: [ 1171.604927] usb 6-1: new full-speed > USB device number 2 using xhci_hcd > Sep 1 15:56:57 master kernel: [ 1176.608751] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 15:57:02 master kernel: [ 1181.813744] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 15:57:03 master kernel: [ 1182.014895] usb 6-1: device not > accepting address 2, error -62 > Sep 1 15:57:03 master kernel: [ 1182.014942] xhci_hcd 0000:03:00.0: > Bad Slot ID 1 > Sep 1 15:57:03 master kernel: [ 1182.014945] xhci_hcd 0000:03:00.0: > Could not allocate xHCI USB device data structures > Sep 1 15:57:03 master kernel: [ 1182.014950] hub 6-0:1.0: couldn't > allocate port 1 usb_device > Sep 1 15:57:03 master kernel: [ 1182.014967] hub 6-0:1.0: hub_suspend > Sep 1 15:57:03 master kernel: [ 1182.014983] usb usb6: bus > auto-suspend, wakeup 1 > Sep 1 16:00:17 master kernel: [ 1376.248867] usb usb6: usb wakeup-resume > Sep 1 16:00:17 master kernel: [ 1376.248875] usb usb6: usb auto-resume > Sep 1 16:00:17 master kernel: [ 1376.248894] hub 6-0:1.0: hub_resume > Sep 1 16:00:17 master kernel: [ 1376.248905] hub 6-0:1.0: port 1: > status 0101 change 0000 > Sep 1 16:00:17 master kernel: [ 1376.248910] hub 6-0:1.0: port 2: > status 0101 change 0001 > Sep 1 16:00:17 master kernel: [ 1376.349888] hub 6-0:1.0: state 7 > ports 2 chg 0006 evt 0000 > Sep 1 16:00:17 master kernel: [ 1376.349898] hub 6-0:1.0: port 1, > status 0101, change 0000, 12 Mb/s > Sep 1 16:00:17 master kernel: [ 1376.451953] usb 6-1: new full-speed > USB device number 3 using xhci_hcd > Sep 1 16:00:22 master kernel: [ 1381.455764] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:27 master kernel: [ 1386.660767] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:27 master kernel: [ 1386.861922] usb 6-1: device not > accepting address 3, error -62 > Sep 1 16:00:27 master kernel: [ 1386.861977] xhci_hcd 0000:03:00.0: > Bad Slot ID 2 > Sep 1 16:00:27 master kernel: [ 1386.861980] xhci_hcd 0000:03:00.0: > Could not allocate xHCI USB device data structures > Sep 1 16:00:27 master kernel: [ 1386.861985] hub 6-0:1.0: couldn't > allocate port 1 usb_device > Sep 1 16:00:27 master kernel: [ 1386.862006] hub 6-0:1.0: port 2, > status 0101, change 0000, 12 Mb/s > Sep 1 16:00:27 master kernel: [ 1386.964011] usb 6-2: new full-speed > USB device number 4 using xhci_hcd > Sep 1 16:00:32 master kernel: [ 1391.967825] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:38 master kernel: [ 1397.172814] xhci_hcd 0000:03:00.0: > Timeout while waiting for address device command > Sep 1 16:00:38 master kernel: [ 1397.373975] usb 6-2: device not > accepting address 4, error -62 > Sep 1 16:00:38 master kernel: [ 1397.374027] xhci_hcd 0000:03:00.0: > Bad Slot ID 3 > Sep 1 16:00:38 master kernel: [ 1397.374030] xhci_hcd 0000:03:00.0: > Could not allocate xHCI USB device data structures > Sep 1 16:00:38 master kernel: [ 1397.374035] hub 6-0:1.0: couldn't > allocate port 2 usb_device > Sep 1 16:00:38 master kernel: [ 1397.374052] hub 6-0:1.0: hub_suspend > Sep 1 16:00:38 master kernel: [ 1397.374077] usb usb6: bus > auto-suspend, wakeup 1 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
