From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>
MSM USB3.0 core wrapper consist of USB3.0 IP from Synopsys
(SNPS) and HS, SS PHY's control and configuration registers.
It could operate in device mode (SS, HS, FS) and host
mode (SS, HS, FS, LS).
Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
---
.../devicetree/bindings/usb/msm-ssusb.txt | 104 ++++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/msm-ssusb.txt
diff --git a/Documentation/devicetree/bindings/usb/msm-ssusb.txt b/Documentation/devicetree/bindings/usb/msm-ssusb.txt
new file mode 100644
index 0000000..f57ba8d
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/msm-ssusb.txt
@@ -0,0 +1,104 @@
+MSM SuperSpeed DWC3 USB SoC controller
+
+
+MSM DW Highspeed USB PHY
+========================
+Required properities :
+- compatible : sould be "qcom,dw-hsphy";
+- reg : offset and length of the register set in the memory map
+- clocks : phandles to clock instances of the device tree nodes
+- clock-names :
+ "xo" : External reference clock 19 MHz
+ "sleep_a" : Sleep clock, used when USB3 core goes into low
+ power mode (U3).
+<supply-name>-supply : phandle to the regulator device tree node
+Required "supply-name" are:
+ "v1p8" : 1.8v supply for HSPHY
+ "v3p3" : 3.3v supply for HSPHY
+ "vbus" : vbus supply for host mode
+ "vddcx" : vdd supply for HS-PHY digital circuit operation
+
+MSM DW Superspeed USB PHY
+=========================
+Required properities :
+- compatible : sould be "qcom,dw-ssphy";
+- reg : offset and length of the register set in the memory map
+- clocks : phandles to clock instances of the device tree nodes
+- clock-names :
+ "xo" : External reference clock 19 MHz
+ "ref" : Reference clock - used in host mode.
+<supply-name>-supply : phandle to the regulator device tree node
+Required "supply-name" are:
+ "v1p8" : 1.8v supply for SS-PHY
+ "vddcx" : vdd supply for SS-PHY digital circuit operation
+
+MSM DWC3 controller wrapper
+===========================
+Required properties :
+- compatible : should be "qcom,dwc3"
+- reg : offset and length of the register set in the memory map
+ offset and length of the TCSR register for routing USB
+ signals to either picoPHY0 or picoPHY1.
+- clocks : phandles to clock instances of the device tree nodes
+- clock-names :
+ "core" : Master/Core clock, have to be >= 125 MHz for SS
+ operation and >= 60MHz for HS operation
+ "iface" : System bus AXI clock
+ "sleep" : Sleep clock, used when USB3 core goes into low
+ power mode (U3).
+ "utmi" : Generated by HS-PHY. Used to clock the low power
+ parts of thr HS Link layer.
+Optional properties :
+- gdsc-supply : phandle to the globally distributed switch controller
+ regulator node to the USB controller.
+Required child node:
+A child node must exist to represent the core DWC3 IP block. The name of
+the node is not important. The content of the node is defined in dwc3.txt.
+
+Example device nodes:
+
+ dw_hsphy: phy@f92f8800 {
+ compatible = "qcom,dw-hsphy";
+ reg = <0xf92f8800 0x30>;
+
+ clocks = <&cxo>, <&usb2a_phy_sleep_cxc>;
+ clock-names = "xo", "sleep_a";
+
+ vbus-supply = <&supply>;
+ vddcx-supply = <&supply>;
+ v1p8-supply = <&supply>;
+ v3p3-supply = <&supply>;
+ };
+
+ dw_ssphy: phy@f92f8830 {
+ compatible = "qcom,dw-ssphy";
+ reg = <0xf92f8830 0x30>;
+
+ clocks = <&cxo>, <&usb30_mock_utmi_cxc>;
+ clock-names = "xo", "ref";
+
+ vddcx-supply = <&supply>;
+ v1p8-supply = <&supply>;
+ };
+
+ usb@fd4ab000 {
+ compatible = "qcom,dwc3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xfd4ab000 0x4>;
+
+ clocks = <&usb30_master_cxc>, <&sys_noc_usb3_axi_cxc>,
+ <&usb30_sleep_cxc>, <&usb30_mock_utmi_cxc>;
+ clock-names = "core", "iface", "sleep", "utmi";
+
+ gdsc-supply = <&supply>;
+
+ ranges;
+ dwc3@f9200000 {
+ compatible = "snps,dwc3";
+ reg = <0xf9200000 0xcd00>;
+ interrupts = <0 131 0>;
+ usb-phy = <&dw_hsphy>, <&dw_ssphy>;
+ tx-fifo-resize;
+ };
+ };
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
