We model the HUB_RESET GPIO as a fixed regulator device. This regulator
is then used as "reset" supply for the USB PHY device and is managed
by the PHY driver.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
arch/arm/mach-omap2/board-omap4panda.c | 48 ++++++++++++++++++++++----------
1 files changed, 33 insertions(+), 15 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index a4831cc..fd2f907 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -132,6 +132,38 @@ static struct platform_device btwilink_device = {
.id = -1,
};
+/* Regulator for USB HUB/PHY reset */
+static struct regulator_consumer_supply hub_reset_supplies[] = {
+/* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.0"),
+};
+
+static struct regulator_init_data hub_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hub_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hub_reset_supplies),
+};
+
+static struct fixed_voltage_config hub_reset_config = {
+ .supply_name = "hub_reset",
+ .microvolts = 3300000,
+ .gpio = GPIO_HUB_NRESET,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hub_reset_data,
+};
+
+static struct platform_device hub_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = 3,
+ .dev = {
+ .platform_data = &hub_reset_config,
+ },
+};
+
/* Regulator for USB HUB supply */
static struct regulator_consumer_supply hub_power_supplies[] = {
/* Link PHY device to USB HUB supply so it gets enabled in the PHY driver */
@@ -171,6 +203,7 @@ static struct platform_device *panda_devices[] __initdata = {
&panda_hdmi_audio_codec,
&btwilink_device,
&hub_power_device,
+ &hub_reset_device,
};
static struct nop_usb_xceiv_platform_data phy_pdata0 = {
@@ -196,25 +229,10 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.phy_config[0] = &phy_config0,
};
-static struct gpio panda_ehci_gpios[] __initdata = {
- { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
-};
-
static void __init omap4_ehci_init(void)
{
int ret;
- /* disable the power to the usb hub prior to init and reset phy+hub */
- ret = gpio_request_array(panda_ehci_gpios,
- ARRAY_SIZE(panda_ehci_gpios));
- if (ret) {
- pr_err("Unable to initialize EHCI power/reset\n");
- return;
- }
-
- gpio_export(GPIO_HUB_NRESET, 0);
- gpio_set_value(GPIO_HUB_NRESET, 1);
-
/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
ret = clk_add_alias("main_clk", "nop_usb_xceiv.0", "auxclk3_ck", NULL);
if (ret)
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
