We model the HUB_POWER GPIO as a fixed regulator device. This regulator
is then used as "vcc" supply for the USB PHY device and is managed
by the PHY driver.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
arch/arm/mach-omap2/board-omap4panda.c | 38 +++++++++++++++++++++++++++----
1 files changed, 33 insertions(+), 5 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 350c4db..a4831cc 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -132,12 +132,45 @@ static struct platform_device btwilink_device = {
.id = -1,
};
+/* Regulator for USB HUB supply */
+static struct regulator_consumer_supply hub_power_supplies[] = {
+/* Link PHY device to USB HUB supply so it gets enabled in the PHY driver */
+ REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.0"),
+};
+
+static struct regulator_init_data hub_power_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hub_power_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hub_power_supplies),
+};
+
+static struct fixed_voltage_config hub_power_config = {
+ .supply_name = "vhub",
+ .microvolts = 3300000,
+ .gpio = GPIO_HUB_POWER,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+ .init_data = &hub_power_data,
+};
+
+static struct platform_device hub_power_device = {
+ .name = "reg-fixed-voltage",
+ .id = 2,
+ .dev = {
+ .platform_data = &hub_power_config,
+ },
+};
+
static struct platform_device *panda_devices[] __initdata = {
&leds_gpio,
&wl1271_device,
&panda_abe_audio,
&panda_hdmi_audio_codec,
&btwilink_device,
+ &hub_power_device,
};
static struct nop_usb_xceiv_platform_data phy_pdata0 = {
@@ -164,7 +197,6 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
};
static struct gpio panda_ehci_gpios[] __initdata = {
- { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" },
{ GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
};
@@ -180,7 +212,6 @@ static void __init omap4_ehci_init(void)
return;
}
- gpio_export(GPIO_HUB_POWER, 0);
gpio_export(GPIO_HUB_NRESET, 0);
gpio_set_value(GPIO_HUB_NRESET, 1);
@@ -190,9 +221,6 @@ static void __init omap4_ehci_init(void)
pr_err("Failed to add main_clk alias to auxclk3_ck\n");
usbhs_init(&usbhs_bdata);
-
- /* enable power to hub */
- gpio_set_value(GPIO_HUB_POWER, 1);
}
static struct omap_musb_board_data musb_board_data = {
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
