Re: [PATCH] usb: otg: twl4030: Change TWL4030_MODULE_* ids to TWL_MODULE_*

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Nov 13, 2012 at 10:43:38AM +0100, Peter Ujfalusi wrote:
> To facilitate upcoming cleanup in twl stack.
> No functional changes.
> 
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@xxxxxx>

I guess this one must go together with the rest of your series...

Acked-by: Felipe Balbi <balbi@xxxxxx>

> ---
>  drivers/usb/otg/twl4030-usb.c | 46 ++++++++++++++++++++-----------------------
>  1 file changed, 21 insertions(+), 25 deletions(-)
> 
> diff --git a/drivers/usb/otg/twl4030-usb.c b/drivers/usb/otg/twl4030-usb.c
> index f0d2e75..11b2a12 100644
> --- a/drivers/usb/otg/twl4030-usb.c
> +++ b/drivers/usb/otg/twl4030-usb.c
> @@ -123,10 +123,10 @@
>  #define PHY_CLK_CTRL_STS		0xFF
>  #define PHY_DPLL_CLK			(1 << 0)
>  
> -/* In module TWL4030_MODULE_PM_MASTER */
> +/* In module TWL_MODULE_PM_MASTER */
>  #define STS_HW_CONDITIONS		0x0F
>  
> -/* In module TWL4030_MODULE_PM_RECEIVER */
> +/* In module TWL_MODULE_PM_RECEIVER */
>  #define VUSB_DEDICATED1			0x7D
>  #define VUSB_DEDICATED2			0x7E
>  #define VUSB1V5_DEV_GRP			0x71
> @@ -195,14 +195,14 @@ static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
>  }
>  
>  #define twl4030_usb_write_verify(twl, address, data)	\
> -	twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_USB, (data), (address))
> +	twl4030_i2c_write_u8_verify(twl, TWL_MODULE_USB, (data), (address))
>  
>  static inline int twl4030_usb_write(struct twl4030_usb *twl,
>  		u8 address, u8 data)
>  {
>  	int ret = 0;
>  
> -	ret = twl_i2c_write_u8(TWL4030_MODULE_USB, data, address);
> +	ret = twl_i2c_write_u8(TWL_MODULE_USB, data, address);
>  	if (ret < 0)
>  		dev_dbg(twl->dev,
>  			"TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
> @@ -227,7 +227,7 @@ static inline int twl4030_readb(struct twl4030_usb *twl, u8 module, u8 address)
>  
>  static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
>  {
> -	return twl4030_readb(twl, TWL4030_MODULE_USB, address);
> +	return twl4030_readb(twl, TWL_MODULE_USB, address);
>  }
>  
>  /*-------------------------------------------------------------------------*/
> @@ -264,8 +264,7 @@ static enum omap_musb_vbus_id_status
>  	 * signal is active, the OTG module is activated, and
>  	 * its interrupt may be raised (may wake the system).
>  	 */
> -	status = twl4030_readb(twl, TWL4030_MODULE_PM_MASTER,
> -			STS_HW_CONDITIONS);
> +	status = twl4030_readb(twl, TWL_MODULE_PM_MASTER, STS_HW_CONDITIONS);
>  	if (status < 0)
>  		dev_err(twl->dev, "USB link status err %d\n", status);
>  	else if (status & (BIT(7) | BIT(2))) {
> @@ -372,8 +371,7 @@ static void twl4030_phy_power(struct twl4030_usb *twl, int on)
>  		 * SLEEP. We work around this by clearing the bit after usv3v1
>  		 * is re-activated. This ensures that VUSB3V1 is really active.
>  		 */
> -		twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
> -							VUSB_DEDICATED2);
> +		twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
>  		regulator_enable(twl->usb1v5);
>  		__twl4030_phy_power(twl, 1);
>  		twl4030_usb_write(twl, PHY_CLK_CTRL,
> @@ -419,50 +417,48 @@ static void twl4030_phy_resume(struct twl4030_usb *twl)
>  static int twl4030_usb_ldo_init(struct twl4030_usb *twl)
>  {
>  	/* Enable writing to power configuration registers */
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
> -			TWL4030_PM_MASTER_KEY_CFG1,
> -			TWL4030_PM_MASTER_PROTECT_KEY);
> +	twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
> +			 TWL4030_PM_MASTER_PROTECT_KEY);
>  
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
> -			TWL4030_PM_MASTER_KEY_CFG2,
> -			TWL4030_PM_MASTER_PROTECT_KEY);
> +	twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
> +			 TWL4030_PM_MASTER_PROTECT_KEY);
>  
>  	/* Keep VUSB3V1 LDO in sleep state until VBUS/ID change detected*/
> -	/*twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
> +	/*twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);*/
>  
>  	/* input to VUSB3V1 LDO is from VBAT, not VBUS */
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
>  
>  	/* Initialize 3.1V regulator */
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_DEV_GRP);
>  
>  	twl->usb3v1 = regulator_get(twl->dev, "usb3v1");
>  	if (IS_ERR(twl->usb3v1))
>  		return -ENODEV;
>  
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
>  
>  	/* Initialize 1.5V regulator */
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_DEV_GRP);
>  
>  	twl->usb1v5 = regulator_get(twl->dev, "usb1v5");
>  	if (IS_ERR(twl->usb1v5))
>  		goto fail1;
>  
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
>  
>  	/* Initialize 1.8V regulator */
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_DEV_GRP);
>  
>  	twl->usb1v8 = regulator_get(twl->dev, "usb1v8");
>  	if (IS_ERR(twl->usb1v8))
>  		goto fail2;
>  
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
> +	twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
>  
>  	/* disable access to power configuration registers */
> -	twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0,
> -			TWL4030_PM_MASTER_PROTECT_KEY);
> +	twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
> +			 TWL4030_PM_MASTER_PROTECT_KEY);
>  
>  	return 0;
>  
> -- 
> 1.8.0
> 

-- 
balbi

Attachment: signature.asc
Description: Digital signature


[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux