Richard Zhao <richard.zhao@xxxxxxxxxxxxx> writes:
> On Tue, Sep 11, 2012 at 10:23:55AM +0300, Alexander Shishkin wrote:
>> Richard Zhao <richard.zhao@xxxxxxxxxxxxx> writes:
>>
>> > On Wed, Aug 29, 2012 at 12:48:15PM +0300, Alexander Shishkin wrote:
>> >> Richard Zhao <richard.zhao@xxxxxxxxxxxxx> writes:
>> >>
>> >> > On Wed, Aug 29, 2012 at 11:10:33AM +0300, Alexander Shishkin wrote:
>> >> >> Richard Zhao <richard.zhao@xxxxxxxxxxxxx> writes:
>> >> >>
>> >> >> > On Tue, Aug 28, 2012 at 11:38:23AM +0300, Alexander Shishkin wrote:
>> >> >> >> Richard Zhao <richard.zhao@xxxxxxxxxxxxx> writes:
>> >> >> >>
>> >> >> >> > One role failed, but the other role will possiblly still work.
>> >> >> >> > For example, when udc start failed, if plug in a host device,
>> >> >> >> > it works.
>> >> >> >>
>> >> >> >> If you're a host device, ci->role should be HOST at this point and
>> >> >> >> ci_role_start() shouldn't fail. If ci->role is detected wrongly, the
>> >> >> >> role detection must be fixed. If ci_role_start() fails for host, but it
>> >> >> >> still works when it's called again after the id pin change is detected,
>> >> >> >> again, the problem is elsewhere.
>> >> >> > The check is only for OTG device. For single role device, it just fail
>> >> >> > if it start the role failed.
>> >> >>
>> >> >> Sorry, can you rephrase?
>> >> >>
>> >> >> >>
>> >> >> >> >
>> >> >> >> > Signed-off-by: Richard Zhao <richard.zhao@xxxxxxxxxxxxx>
>> >> >> >> > ---
>> >> >> >> > drivers/usb/chipidea/core.c | 7 +++++--
>> >> >> >> > 1 file changed, 5 insertions(+), 2 deletions(-)
>> >> >> >> >
>> >> >> >> > diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
>> >> >> >> > index 19ef324..8fd390a 100644
>> >> >> >> > --- a/drivers/usb/chipidea/core.c
>> >> >> >> > +++ b/drivers/usb/chipidea/core.c
>> >> >> >> > @@ -473,8 +473,11 @@ static int __devinit ci_hdrc_probe(struct platform_device *pdev)
>> >> >> >> > ret = ci_role_start(ci, ci->role);
>> >> >> >> > if (ret) {
>> >> >> >> > dev_err(dev, "can't start %s role\n", ci_role(ci)->name);
>> >> >> >> > - ret = -ENODEV;
>> >> >> >> > - goto rm_wq;
>> >> >> >> > + ci->role = CI_ROLE_END;
>> >> >> >>
>> >> >> >> So are you relying on id pin interrupt for initializing the role after
>> >> >> >> this? Can you provide more details?
>> >> >> > Yes. The ID pin detect still works. My case is, gadget role failed,
>> >> >> > host role works. I was trying not to ruin host function.
>> >> >>
>> >> >> But it shouldn't even try to start the gadget, because ci_otg_role()
>> >> >> should set ci->role to HOST before ci_role_start() happens.
>> >> > It depends on ID pin. If ID pin is gadget and gadget is not support well,
>> >> > ci_role_start will fail. See below example.
>> >> >>
>> >> >> Another question is, why does gadget start fail?
>> >> > There's one example:
>> >> > If usb phy don't support otg yet, otg_set_peripheral will fail, and
>> >> > then cause udc_start fail.
>> >>
>> >> So you should drop the CI13XXX_REQUIRE_TRANSCEIVER flag from imx
>> >> platform data till the phy is fully implemented.
>> > It's just an example. We can not assume udc_start always success. If it
>> > fails, isn't it better to continue support of host than say game over?
>>
>> Ok, I think what we need here is to rework error handling around role
>> switching, so that we can allow certain things to fail and retry at a
>> later point (say at id pin change), while being careful about the other
>> failures.
>>
>> If this patch is not crucial for imx right now, I'd prefer to leave it
>> out.
> That's OK. but I hope other function related patch can be merged for
> 3.7 :)
Also 6/11 seems quite pointless to me. Otherwise, I'll send them to Greg
today.
Regards,
--
Alex
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
