Re: Re: Re: 3.0 device attached to USB 3.0 hub port doesn't respond address device command after resume

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi All,

I was using the SS hub by VIA Labs,inc.

what I found is that, there is a firmware update available for this SS HUB.

When i went through the Release Notes, they say 
USB 3.0: 
Resolved issue with Intel USB 3.0 Host where devices were occasionally not properly re-enumerated after resuming from S3/S4, warm-boot, or cold boot

http://www.via-labs.com/en/downloads/documents/VL810-Firmware-V9.5-Release-Note.pdf

I upgraded the firmware with their tool (http://www.via-labs.com/en/support/downloads.jsp),  with that , this case "USB 3.0 Device on SS hub on 3.0 port" gets resolved.

Thanks and Regards
Vikas Sajjan

------- Original Message -------
Sender : VIKAS SAJJAN C<vikas.sajjan@xxxxxxxxxxx>  Technical Manager/SISO-Solution 1/Samsung Electronics
Date   : Aug 20, 2012 15:53 (GMT+09:00)
Title  : Re: Re: 3.0 device attached to USB 3.0 hub port doesn't respond address device command after resume
To     : Andiry Xu<andiry@xxxxxxxxx>  elricfu1@xxxxxxxxx  linux-usb@xxxxxxxxxxxxxxx  sarah.a.sharp@xxxxxxxxxxxxxxx  


Hi ,

if i disconnect the hub, after the timeout error , i get these errors...

[  295.496749] hub 4-1:1.0: cannot reset port 3 (err = -71)
[  301.507153] xhci-hcd xhci-hcd: xHCI host not responding to stop endpoint command.
[  301.513153] xhci-hcd xhci-hcd: Assuming host is dying, halting host.
[  301.539664] xhci-hcd xhci-hcd: HC died; cleaning up
[  301.543196] hub 4-1:1.0: cannot reset port 3 (err = -110)
[  301.548456] hub 4-1:1.0: cannot reset port 3 (err = -19)
[  301.553888] PM: resume of devices complete after 159484.626 msecs
[  301.560084] PM: Finishing wakeup.
[  301.563121] Restarting tasks ...
[  301.566756] usb 3-1: USB disconnect, device number 2
[  301.586698] usb 4-1: USB disconnect, device number 2
[  301.596611] done.
[  301.601652] usb 4-1.3: USB disconnect, device number 3
localhost user #
localhost user #

After this 3.0 port becomes DEAD, it does not detect any attach /detach.  

even i tired with another hub, same is the issue...

all the cases of suspend / resume works except this case, by that i mean

1. USB 3.0 Device on 3.0 port - Works fine. 
2. USB 3.0 Device on 2.0 port - Works fine.
3. USB 2.0 Device on 3.0 port - Works fine.
4. USB 2.0 Device on 2.0 port - Works fine.
5. USB 2.0 Device on SS hub on 3.0 port - Works fine.
6. USB 2.0 Device on 2.0 hub on 3.0 port - Works fine. 
7. USB 3.0 Device on 2.0 hub on 3.0 port - Works fine.
8. USB 3.0 Device on SS hub on 2.0 port - Works fine.
9. USB 3.0 Device on SS hub on 3.0 port - FAILS. 
 
Regards
Vikas Sajjan

------- Original Message -------
Sender : Andiry Xu<andiry@xxxxxxxxx> 
Date   : Aug 18, 2012 21:54 (GMT+09:00)
Title  : Re: 3.0 device attached to USB 3.0 hub port doesn't respond address
 device command after resume

On Sat, Aug 18, 2012 at 7:41 PM, VIKAS SAJJAN C
<vikas.sajjan@xxxxxxxxxxx> wrote:
>
> Hi All,
>
> we have added Suspend / resume code for DWC USB 3  controller and xhic-plat.c on 3.4 kernel.
>
> the scenario when i have Corsair 3.0 USB device sitting on VIA 3.0 SS hub connected to 3.0 port,
>
> after resume , i get these error
>
>  176.942208] xhci-hcd xhci-hcd: Timeout while waiting for address device command
> [  202.152208] xhci-hcd xhci-hcd: Timeout while waiting for address device command
> [  202.362207] usb 4-1.1: device not accepting address 3, error -62
> [  227.437201] xhci-hcd xhci-hcd: Timeout while waiting for address device command
> [  252.647205] xhci-hcd xhci-hcd: Timeout while waiting for address device command
> [  252.857201] usb 4-1.1: device not accepting address 3, error -62
> [  277.932206] xhci-hcd xhci-hcd: Timeout while waiting for address device command
> [  303.142208] xhci-hcd xhci-hcd: Timeout while waiting for address device command
> [  303.352202] usb 4-1.1: device not accepting address 3, error -62
>
> i was referring this
> http://www.spinics.net/lists/linux-usb/msg58474.html . but then i found that i already have this patch. ( USB: Set hub depth after USB3 hub reset )
>

What happen if you remove the hub or try a different hub?

Thanks,
Andiry

> Regards
> Vikas Sajjan
ÿôèº{.nÇ+‰·Ÿ®‰­†+%ŠËÿ±éݶ¥Šwÿº{.nÇ+‰·¥Š{±þëþ)í…æèw*jg¬±¨¶‰šŽŠÝ¢jÿ¾«þG«?éÿ¢¸¢·¦j:+v‰¨ŠwèjØm¶Ÿÿþø¯ù®w¥þŠàþf£¢·hš?â?úÿ†Ù¥



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux