On Mon, Jul 23, 2012 at 08:25:20PM +0200, e.kleinmentink@xxxxxxxxx wrote: > recently bought the following PCIe USB3.0 card with a NEC/renesas 720201 > chipset: > > USB controller: Renesas Technology Corp. Device 0014 (rev 03) > > Linux does not load a driver for it (looking with lspci -k). Tried with Ubuntu > 12.04 and Fedora 17. Well, technically, the driver did try to load, but the probe failed. > [ 1.026858] xhci_hcd 0000:03:00.0: // Halt the HC > [ 1.026867] xhci_hcd 0000:03:00.0: Resetting HCD > [ 1.026871] xhci_hcd 0000:03:00.0: // Reset the HC > [ 1.564629] xhci_hcd 0000:03:00.0: can't setup > [ 1.564637] xhci_hcd 0000:03:00.0: USB bus 3 deregistered > [ 1.564776] xhci_hcd 0000:03:00.0: init 0000:03:00.0 fail, -110 > [ 1.564799] xhci_hcd: probe of 0000:03:00.0 failed with error -110 It looks like resetting the host controller timed out. I'll send you a patch to test shortly. Sarah Sharp > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 3.5.0edje (root@x2) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #2 SMP Sun Jul 22 22:43:32 CEST 2012 > [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0edje root=UUID=708c0650-2212-46a0-8a9a-ebc8bdbf0870 ro crashkernel=384M-2G:64M,2G-:128M quiet splash vt.handoff=7 > [ 0.000000] KERNEL supported cpus: > [ 0.000000] Intel GenuineIntel > [ 0.000000] AMD AuthenticAMD > [ 0.000000] Centaur CentaurHauls > [ 0.000000] e820: BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009cbff] usable > [ 0.000000] BIOS-e820: [mem 0x000000000009cc00-0x000000000009ffff] reserved > [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved > [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffeffff] usable > [ 0.000000] BIOS-e820: [mem 0x00000000bfff0000-0x00000000bfff2fff] ACPI NVS > [ 0.000000] BIOS-e820: [mem 0x00000000bfff3000-0x00000000bfffffff] ACPI data > [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved > [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved > [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013fffffff] usable > [ 0.000000] NX (Execute Disable) protection: active > [ 0.000000] DMI 2.3 present. > [ 0.000000] DMI: System manufacturer System Product Name/A8N-E, BIOS ASUS A8N-E ACPI BIOS Revision 1011-004 01/20/2006 > [ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved > [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable > [ 0.000000] No AGP bridge found > [ 0.000000] e820: last_pfn = 0x140000 max_arch_pfn = 0x400000000 > [ 0.000000] MTRR default type: uncachable > [ 0.000000] MTRR fixed ranges enabled: > [ 0.000000] 00000-9FFFF write-back > [ 0.000000] A0000-BFFFF uncachable > [ 0.000000] C0000-C7FFF write-protect > [ 0.000000] C8000-FFFFF uncachable > [ 0.000000] MTRR variable ranges enabled: > [ 0.000000] 0 base 0000000000 mask FF80000000 write-back > [ 0.000000] 1 base 0080000000 mask FFC0000000 write-back > [ 0.000000] 2 base 0100000000 mask FFC0000000 write-back > [ 0.000000] 3 disabled > [ 0.000000] 4 disabled > [ 0.000000] 5 disabled > [ 0.000000] 6 disabled > [ 0.000000] 7 disabled > [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 > [ 0.000000] e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved > [ 0.000000] e820: last_pfn = 0xbfff0 max_arch_pfn = 0x400000000 > [ 0.000000] found SMP MP-table at [mem 0x000f54f0-0x000f54ff] mapped at [ffff8800000f54f0] > [ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff] > [ 0.000000] Base memory trampoline at [ffff880000096000] 96000 size 24576 > [ 0.000000] init_memory_mapping: [mem 0x00000000-0xbffeffff] > [ 0.000000] [mem 0x00000000-0xbfdfffff] page 2M > [ 0.000000] [mem 0xbfe00000-0xbffeffff] page 4k > [ 0.000000] kernel direct mapping tables up to 0xbffeffff @ [mem 0x1f9fc000-0x1fffffff] > [ 0.000000] init_memory_mapping: [mem 0x100000000-0x13fffffff] > [ 0.000000] [mem 0x100000000-0x13fffffff] page 2M > [ 0.000000] kernel direct mapping tables up to 0x13fffffff @ [mem 0xbffea000-0xbffeffff] > [ 0.000000] RAMDISK: [mem 0x35806000-0x36bfafff] > [ 0.000000] Reserving 128MB of memory at 720MB for crashkernel (System RAM: 4095MB) > [ 0.000000] ACPI: RSDP 00000000000f7580 00014 (v00 Nvidia) > [ 0.000000] ACPI: RSDT 00000000bfff3040 00030 (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000) > [ 0.000000] ACPI: FACP 00000000bfff30c0 00074 (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000) > [ 0.000000] ACPI: DSDT 00000000bfff3180 065F2 (v01 NVIDIA AWRDACPI 00001000 MSFT 0100000E) > [ 0.000000] ACPI: FACS 00000000bfff0000 00040 > [ 0.000000] ACPI: MCFG 00000000bfff9880 0003C (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000) > [ 0.000000] ACPI: APIC 00000000bfff97c0 0007C (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000) > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] Scanning NUMA topology in Northbridge 24 > [ 0.000000] No NUMA configuration found > [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000013fffffff] > [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff] > [ 0.000000] NODE_DATA [mem 0x13fffc000-0x13fffffff] > [ 0.000000] [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013b600000-ffff88013f5fffff] on node 0 > [ 0.000000] Zone ranges: > [ 0.000000] DMA [mem 0x00010000-0x00ffffff] > [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] > [ 0.000000] Normal [mem 0x100000000-0x13fffffff] > [ 0.000000] Movable zone start for each node > [ 0.000000] Early memory node ranges > [ 0.000000] node 0: [mem 0x00010000-0x0009bfff] > [ 0.000000] node 0: [mem 0x00100000-0xbffeffff] > [ 0.000000] node 0: [mem 0x100000000-0x13fffffff] > [ 0.000000] On node 0 totalpages: 1048444 > [ 0.000000] DMA zone: 64 pages used for memmap > [ 0.000000] DMA zone: 6 pages reserved > [ 0.000000] DMA zone: 3910 pages, LIFO batch:0 > [ 0.000000] DMA32 zone: 16320 pages used for memmap > [ 0.000000] DMA32 zone: 766000 pages, LIFO batch:31 > [ 0.000000] Normal zone: 4096 pages used for memmap > [ 0.000000] Normal zone: 258048 pages, LIFO batch:31 > [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. > [ 0.000000] If you got timer trouble try acpi_use_timer_override > [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: BIOS IRQ0 override ignored. > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] ACPI: IRQ14 used by override. > [ 0.000000] ACPI: IRQ15 used by override. > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs > [ 0.000000] nr_irqs_gsi: 40 > [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 > [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 > [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 > [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 > [ 0.000000] PM: Registered nosave memory: 00000000bfff0000 - 00000000bfff3000 > [ 0.000000] PM: Registered nosave memory: 00000000bfff3000 - 00000000c0000000 > [ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000 > [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000 > [ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000 > [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 0000000100000000 > [ 0.000000] e820: [mem 0xc0000000-0xdfffffff] available for PCI devices > [ 0.000000] Booting paravirtualized kernel on bare hardware > [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:2 nr_node_ids:1 > [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88013fc00000 s83328 r8192 d23168 u1048576 > [ 0.000000] pcpu-alloc: s83328 r8192 d23168 u1048576 alloc=1*2097152 > [ 0.000000] pcpu-alloc: [0] 0 1 > [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1027958 > [ 0.000000] Policy zone: Normal > [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0edje root=UUID=708c0650-2212-46a0-8a9a-ebc8bdbf0870 ro crashkernel=384M-2G:64M,2G-:128M quiet splash vt.handoff=7 > [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) > [ 0.000000] __ex_table already sorted, skipping sort > [ 0.000000] Checking aperture... > [ 0.000000] No AGP bridge found > [ 0.000000] Node 0: aperture @ b4000000 size 32 MB > [ 0.000000] Aperture pointing to e820 RAM. Ignoring. > [ 0.000000] Your BIOS doesn't leave a aperture memory hole > [ 0.000000] Please enable the IOMMU option in the BIOS setup > [ 0.000000] This costs you 64 MB of RAM > [ 0.000000] Mapping aperture over 65536 KB of RAM @ b4000000 > [ 0.000000] PM: Registered nosave memory: 00000000b4000000 - 00000000b8000000 > [ 0.000000] Memory: 3829104k/5242880k available (6631k kernel code, 1049104k absent, 364672k reserved, 6530k data, 912k init) > [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. > [ 0.000000] NR_IRQS:16640 nr_irqs:512 16 > [ 0.000000] spurious 8259A interrupt: IRQ7. > [ 0.000000] Console: colour dummy device 80x25 > [ 0.000000] console [tty0] enabled > [ 0.000000] allocated 16777216 bytes of page_cgroup > [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups > [ 0.000000] Fast TSC calibration using PIT > [ 0.000000] Detected 2010.449 MHz processor. > [ 0.000000] Marking TSC unstable due to TSCs unsynchronized > [ 0.004007] Calibrating delay loop (skipped), value calculated using timer frequency.. 4020.89 BogoMIPS (lpj=8041796) > [ 0.004011] pid_max: default: 32768 minimum: 301 > [ 0.004045] Security Framework initialized > [ 0.004072] AppArmor: AppArmor initialized > [ 0.004585] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) > [ 0.009707] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) > [ 0.011437] Mount-cache hash table entries: 256 > [ 0.011754] Initializing cgroup subsys cpuacct > [ 0.011757] Initializing cgroup subsys memory > [ 0.011772] Initializing cgroup subsys devices > [ 0.011774] Initializing cgroup subsys freezer > [ 0.011776] Initializing cgroup subsys blkio > [ 0.011778] Initializing cgroup subsys perf_event > [ 0.011815] tseg: 0000000000 > [ 0.011833] CPU: Physical Processor ID: 0 > [ 0.011835] CPU: Processor Core ID: 0 > [ 0.011837] mce: CPU supports 5 MCE banks > [ 0.013908] ACPI: Core revision 20120320 > [ 0.019018] ftrace: allocating 24529 entries in 96 pages > [ 0.028499] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1 > [ 0.070848] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 > [ 0.072003] Performance Events: AMD PMU driver. > [ 0.072003] ... version: 0 > [ 0.072003] ... bit width: 48 > [ 0.072003] ... generic registers: 4 > [ 0.072003] ... value mask: 0000ffffffffffff > [ 0.072003] ... max period: 00007fffffffffff > [ 0.072003] ... fixed-purpose events: 0 > [ 0.072003] ... event mask: 000000000000000f > [ 0.072003] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. > [ 0.072003] Booting Node 0, Processors #1 Ok. > [ 0.156164] Brought up 2 CPUs > [ 0.156167] Total of 2 processors activated (8041.77 BogoMIPS). > [ 0.156785] devtmpfs: initialized > [ 0.158240] EVM: security.selinux > [ 0.158241] EVM: security.SMACK64 > [ 0.158243] EVM: security.capability > [ 0.158268] PM: Registering ACPI NVS region [mem 0xbfff0000-0xbfff2fff] (12288 bytes) > [ 0.160405] dummy: > [ 0.160441] RTC time: 0:26:09, date: 07/23/12 > [ 0.160495] NET: Registered protocol family 16 > [ 0.160671] node 0 link 0: io port [1000, fffff] > [ 0.160674] TOM: 00000000c0000000 aka 3072M > [ 0.160677] node 0 link 0: mmio [e0000000, efffffff] > [ 0.160681] node 0 link 0: mmio [feb00000, fec0ffff] > [ 0.160684] node 0 link 0: mmio [a0000, bffff] > [ 0.160687] node 0 link 0: mmio [c0000000, fed3ffff] > [ 0.160689] TOM2: 0000000140000000 aka 5120M > [ 0.160692] bus: [00, ff] on node 0 link 0 > [ 0.160694] bus: 00 [io 0x0000-0xffff] > [ 0.160697] bus: 00 [mem 0xc0000000-0xffffffff] > [ 0.160698] bus: 00 [mem 0xfeb00000-0xfec0ffff] > [ 0.160700] bus: 00 [mem 0x000a0000-0x000bffff] > [ 0.160702] bus: 00 [mem 0x140000000-0xfcffffffff] > [ 0.160761] ACPI: bus type pci registered > [ 0.160832] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) > [ 0.160835] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820 > [ 0.177211] PCI: Using configuration type 1 for base access > [ 0.178488] bio: create slab <bio-0> at 0 > [ 0.178488] ACPI: Added _OSI(Module Device) > [ 0.178488] ACPI: Added _OSI(Processor Device) > [ 0.178488] ACPI: Added _OSI(3.0 _SCP Extensions) > [ 0.178488] ACPI: Added _OSI(Processor Aggregator Device) > [ 0.180355] ACPI: EC: Look up EC in DSDT > [ 0.186137] ACPI: Interpreter enabled > [ 0.186143] ACPI: (supports S0 S1 S3 S4 S5) > [ 0.186170] ACPI: Using IOAPIC for interrupt routing > [ 0.193107] ACPI: No dock devices found. > [ 0.193117] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug > [ 0.193184] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) > [ 0.193267] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored) > [ 0.193270] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored) > [ 0.193274] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) > [ 0.193276] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored) > [ 0.193279] pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xfebfffff] (ignored) > [ 0.193282] PCI: root bus 00: hardware-probed resources > [ 0.193326] PCI host bridge to bus 0000:00 > [ 0.193330] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] > [ 0.193333] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff] > [ 0.193336] pci_bus 0000:00: root bus resource [mem 0xfeb00000-0xfec0ffff] > [ 0.193339] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff] > [ 0.193342] pci_bus 0000:00: root bus resource [mem 0x140000000-0xfcffffffff] > [ 0.193358] pci 0000:00:00.0: [10de:005e] type 00 class 0x058000 > [ 0.193436] pci 0000:00:01.0: [10de:0050] type 00 class 0x060100 > [ 0.193458] HPET not enabled in BIOS. You might try hpet=force boot option > [ 0.193472] pci 0000:00:01.1: [10de:0052] type 00 class 0x0c0500 > [ 0.193480] pci 0000:00:01.1: reg 10: [io 0xdc00-0xdc1f] > [ 0.193493] pci 0000:00:01.1: reg 20: [io 0x4c00-0x4c3f] > [ 0.193499] pci 0000:00:01.1: reg 24: [io 0x4c40-0x4c7f] > [ 0.193515] pci 0000:00:01.1: PME# supported from D3hot D3cold > [ 0.193533] pci 0000:00:02.0: [10de:005a] type 00 class 0x0c0310 > [ 0.193541] pci 0000:00:02.0: reg 10: [mem 0xd7103000-0xd7103fff] > [ 0.193569] pci 0000:00:02.0: supports D1 D2 > [ 0.193572] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.193586] pci 0000:00:02.1: [10de:005b] type 00 class 0x0c0320 > [ 0.193595] pci 0000:00:02.1: reg 10: [mem 0xfeb00000-0xfeb000ff] > [ 0.193629] pci 0000:00:02.1: supports D1 D2 > [ 0.193631] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.193655] pci 0000:00:06.0: [10de:0053] type 00 class 0x01018a > [ 0.193673] pci 0000:00:06.0: reg 20: [io 0xf000-0xf00f] > [ 0.193701] pci 0000:00:07.0: [10de:0054] type 00 class 0x010185 > [ 0.193709] pci 0000:00:07.0: reg 10: [io 0x09f0-0x09f7] > [ 0.193714] pci 0000:00:07.0: reg 14: [io 0x0bf0-0x0bf3] > [ 0.193719] pci 0000:00:07.0: reg 18: [io 0x0970-0x0977] > [ 0.193724] pci 0000:00:07.0: reg 1c: [io 0x0b70-0x0b73] > [ 0.193729] pci 0000:00:07.0: reg 20: [io 0xd800-0xd80f] > [ 0.193734] pci 0000:00:07.0: reg 24: [mem 0xd7102000-0xd7102fff] > [ 0.193758] pci 0000:00:08.0: [10de:0055] type 00 class 0x010185 > [ 0.193766] pci 0000:00:08.0: reg 10: [io 0x09e0-0x09e7] > [ 0.193771] pci 0000:00:08.0: reg 14: [io 0x0be0-0x0be3] > [ 0.193776] pci 0000:00:08.0: reg 18: [io 0x0960-0x0967] > [ 0.193782] pci 0000:00:08.0: reg 1c: [io 0x0b60-0x0b63] > [ 0.193787] pci 0000:00:08.0: reg 20: [io 0xc400-0xc40f] > [ 0.193792] pci 0000:00:08.0: reg 24: [mem 0xd7101000-0xd7101fff] > [ 0.193815] pci 0000:00:09.0: [10de:005c] type 01 class 0x060401 > [ 0.193836] pci 0000:00:0a.0: [10de:0057] type 00 class 0x068000 > [ 0.193845] pci 0000:00:0a.0: reg 10: [mem 0xd7100000-0xd7100fff] > [ 0.193850] pci 0000:00:0a.0: reg 14: [io 0xb000-0xb007] > [ 0.193875] pci 0000:00:0a.0: supports D1 D2 > [ 0.193878] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.193893] pci 0000:00:0b.0: [10de:005d] type 01 class 0x060400 > [ 0.193924] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.193941] pci 0000:00:0c.0: [10de:005d] type 01 class 0x060400 > [ 0.193970] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.193987] pci 0000:00:0d.0: [10de:005d] type 01 class 0x060400 > [ 0.194016] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.194034] pci 0000:00:0e.0: [10de:005d] type 01 class 0x060400 > [ 0.194063] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold > [ 0.194084] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000 > [ 0.194108] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000 > [ 0.194128] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000 > [ 0.194147] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000 > [ 0.194190] pci 0000:05:07.0: [105a:3d17] type 00 class 0x018000 > [ 0.194202] pci 0000:05:07.0: reg 10: [io 0xa000-0xa07f] > [ 0.194214] pci 0000:05:07.0: reg 18: [io 0xa400-0xa4ff] > [ 0.194222] pci 0000:05:07.0: reg 1c: [mem 0xd6020000-0xd6020fff] > [ 0.194230] pci 0000:05:07.0: reg 20: [mem 0xd6000000-0xd601ffff] > [ 0.194243] pci 0000:05:07.0: reg 30: [mem 0xd5000000-0xd5007fff pref] > [ 0.194262] pci 0000:05:07.0: supports D1 > [ 0.194277] pci 0000:05:08.0: [1274:5880] type 00 class 0x040100 > [ 0.194289] pci 0000:05:08.0: reg 10: [io 0xa800-0xa83f] > [ 0.194336] pci 0000:05:08.0: supports D2 > [ 0.194360] pci 0000:00:09.0: PCI bridge to [bus 05-05] (subtractive decode) > [ 0.194363] pci 0000:00:09.0: bridge window [io 0xa000-0xafff] > [ 0.194367] pci 0000:00:09.0: bridge window [mem 0xd5000000-0xd6ffffff] > [ 0.194370] pci 0000:00:09.0: bridge window [io 0x0000-0xffff] (subtractive decode) > [ 0.194373] pci 0000:00:09.0: bridge window [mem 0xc0000000-0xffffffff] (subtractive decode) > [ 0.194376] pci 0000:00:09.0: bridge window [mem 0xfeb00000-0xfec0ffff] (subtractive decode) > [ 0.194379] pci 0000:00:09.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) > [ 0.194382] pci 0000:00:09.0: bridge window [mem 0x140000000-0xfcffffffff] (subtractive decode) > [ 0.194427] pci 0000:04:00.0: [8086:10d3] type 00 class 0x020000 > [ 0.194447] pci 0000:04:00.0: reg 10: [mem 0xd4080000-0xd409ffff] > [ 0.194461] pci 0000:04:00.0: reg 14: [mem 0xd4000000-0xd407ffff] > [ 0.194476] pci 0000:04:00.0: reg 18: [io 0x9000-0x901f] > [ 0.194490] pci 0000:04:00.0: reg 1c: [mem 0xd40a0000-0xd40a3fff] > [ 0.194529] pci 0000:04:00.0: reg 30: [mem 0xd3000000-0xd303ffff pref] > [ 0.194602] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold > [ 0.200034] pci 0000:00:0b.0: PCI bridge to [bus 04-04] > [ 0.200038] pci 0000:00:0b.0: bridge window [io 0x9000-0x9fff] > [ 0.200041] pci 0000:00:0b.0: bridge window [mem 0xd3000000-0xd4ffffff] > [ 0.200096] pci 0000:03:00.0: [1912:0014] type 00 class 0x0c0330 > [ 0.200125] pci 0000:03:00.0: reg 10: [mem 0xd7000000-0xd7001fff 64bit] > [ 0.200268] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold > [ 0.208027] pci 0000:00:0c.0: PCI bridge to [bus 03-03] > [ 0.208032] pci 0000:00:0c.0: bridge window [mem 0xd7000000-0xd70fffff] > [ 0.208055] pci 0000:00:0d.0: PCI bridge to [bus 02-02] > [ 0.208090] pci 0000:01:00.0: [10de:0de1] type 00 class 0x030000 > [ 0.208099] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xd0ffffff] > [ 0.208109] pci 0000:01:00.0: reg 14: [mem 0xc0000000-0xc7ffffff 64bit pref] > [ 0.208119] pci 0000:01:00.0: reg 1c: [mem 0xc8000000-0xc9ffffff 64bit pref] > [ 0.208127] pci 0000:01:00.0: reg 24: [io 0x8000-0x807f] > [ 0.208134] pci 0000:01:00.0: reg 30: [mem 0xd1000000-0xd107ffff pref] > [ 0.208185] pci 0000:01:00.1: [10de:0bea] type 00 class 0x040300 > [ 0.208194] pci 0000:01:00.1: reg 10: [mem 0xd2000000-0xd2003fff] > [ 0.216023] pci 0000:00:0e.0: PCI bridge to [bus 01-01] > [ 0.216028] pci 0000:00:0e.0: bridge window [io 0x8000-0x8fff] > [ 0.216031] pci 0000:00:0e.0: bridge window [mem 0xd0000000-0xd2ffffff] > [ 0.216035] pci 0000:00:0e.0: bridge window [mem 0xc0000000-0xcfffffff 64bit pref] > [ 0.216048] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 0.216232] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] > [ 0.216429] pci0000:00: Requesting ACPI _OSC control (0x1d) > [ 0.216433] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d > [ 0.216435] ACPI _OSC control for PCIe not granted, disabling ASPM > [ 0.250962] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15) > [ 0.251017] ACPI: PCI Interrupt Link [LNK2] (IRQs *3 4 5 7 9 10 11 12 14 15) > [ 0.251069] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 10 *11 12 14 15) > [ 0.251121] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 7 9 10 11 12 14 15) > [ 0.251172] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. > [ 0.251225] ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15) > [ 0.251275] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. > [ 0.251328] ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 7 9 10 11 12 14 15) > [ 0.251386] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. > [ 0.251437] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. > [ 0.251490] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15) > [ 0.251541] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15) > [ 0.251591] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. > [ 0.251650] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15) > [ 0.251711] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15) > [ 0.251775] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. > [ 0.251848] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0 > [ 0.251913] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0 > [ 0.251978] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0 > [ 0.252050] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0 > [ 0.252083] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. > [ 0.252157] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 > [ 0.252229] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. > [ 0.252302] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 > [ 0.252374] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. > [ 0.252446] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. > [ 0.252519] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 > [ 0.252590] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 > [ 0.252662] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. > [ 0.252740] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 > [ 0.252818] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 > [ 0.252896] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. > [ 0.253008] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none > [ 0.253008] vgaarb: loaded > [ 0.253008] vgaarb: bridge control possible 0000:01:00.0 > [ 0.253008] SCSI subsystem initialized > [ 0.253008] libata version 3.00 loaded. > [ 0.253008] ACPI: bus type usb registered > [ 0.253008] usbcore: registered new interface driver usbfs > [ 0.253008] usbcore: registered new interface driver hub > [ 0.253008] usbcore: registered new device driver usb > [ 0.253008] PCI: Using ACPI for IRQ routing > [ 0.258979] PCI: pci_cache_line_size set to 64 bytes > [ 0.259005] pci 0000:00:02.1: address space collision: [mem 0xfeb00000-0xfeb000ff] conflicts with PCI Bus #00 [mem 0xfeb00000-0xfec0ffff] > [ 0.259079] Expanded resource reserved due to conflict with PCI Bus #00 > [ 0.259082] e820: reserve RAM buffer [mem 0x0009cc00-0x0009ffff] > [ 0.259085] e820: reserve RAM buffer [mem 0xbfff0000-0xbfffffff] > [ 0.259227] NetLabel: Initializing > [ 0.259229] NetLabel: domain hash size = 128 > [ 0.259230] NetLabel: protocols = UNLABELED CIPSOv4 > [ 0.259248] NetLabel: unlabeled traffic allowed by default > [ 0.270326] AppArmor: AppArmor Filesystem Enabled > [ 0.270382] pnp: PnP ACPI init > [ 0.270406] ACPI: bus type pnp registered > [ 0.270558] pnp 00:00: [bus 00-ff] > [ 0.270562] pnp 00:00: [io 0x0cf8-0x0cff] > [ 0.270565] pnp 00:00: [io 0x0000-0x0cf7 window] > [ 0.270567] pnp 00:00: [io 0x0d00-0xffff window] > [ 0.270570] pnp 00:00: [mem 0x000a0000-0x000bffff window] > [ 0.270573] pnp 00:00: [mem 0x000c0000-0x000dffff window] > [ 0.270576] pnp 00:00: [mem 0xc0000000-0xfebfffff window] > [ 0.270678] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) > [ 0.270701] pnp 00:01: [io 0x4000-0x407f] > [ 0.270708] pnp 00:01: [io 0x4080-0x40ff] > [ 0.270711] pnp 00:01: [io 0x4400-0x447f] > [ 0.270714] pnp 00:01: [io 0x4480-0x44ff] > [ 0.270716] pnp 00:01: [io 0x4800-0x487f] > [ 0.270719] pnp 00:01: [io 0x4880-0x48ff] > [ 0.270795] system 00:01: [io 0x4000-0x407f] has been reserved > [ 0.270798] system 00:01: [io 0x4080-0x40ff] has been reserved > [ 0.270802] system 00:01: [io 0x4400-0x447f] has been reserved > [ 0.270805] system 00:01: [io 0x4480-0x44ff] has been reserved > [ 0.270809] system 00:01: [io 0x4800-0x487f] has been reserved > [ 0.270812] system 00:01: [io 0x4880-0x48ff] has been reserved > [ 0.270816] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) > [ 0.271442] pnp 00:02: [io 0x0010-0x001f] > [ 0.271445] pnp 00:02: [io 0x0022-0x003f] > [ 0.271447] pnp 00:02: [io 0x0044-0x005f] > [ 0.271450] pnp 00:02: [io 0x0062-0x0063] > [ 0.271452] pnp 00:02: [io 0x0065-0x006f] > [ 0.271455] pnp 00:02: [io 0x0074-0x007f] > [ 0.271458] pnp 00:02: [io 0x0091-0x0093] > [ 0.271460] pnp 00:02: [io 0x00a2-0x00bf] > [ 0.271463] pnp 00:02: [io 0x00e0-0x00ef] > [ 0.271466] pnp 00:02: [io 0x04d0-0x04d1] > [ 0.271469] pnp 00:02: [io 0x0800-0x087f] > [ 0.271471] pnp 00:02: [io 0x0290-0x0297] > [ 0.271551] system 00:02: [io 0x04d0-0x04d1] has been reserved > [ 0.271555] system 00:02: [io 0x0800-0x087f] has been reserved > [ 0.271558] system 00:02: [io 0x0290-0x0297] has been reserved > [ 0.271562] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) > [ 0.271578] pnp 00:03: [dma 4] > [ 0.271581] pnp 00:03: [io 0x0000-0x000f] > [ 0.271583] pnp 00:03: [io 0x0080-0x0090] > [ 0.271586] pnp 00:03: [io 0x0094-0x009f] > [ 0.271589] pnp 00:03: [io 0x00c0-0x00df] > [ 0.271630] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active) > [ 0.271649] pnp 00:04: [io 0x0070-0x0073] > [ 0.271666] pnp 00:04: [irq 8] > [ 0.271713] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active) > [ 0.271725] pnp 00:05: [io 0x0061] > [ 0.271771] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active) > [ 0.271782] pnp 00:06: [io 0x00f0-0x00ff] > [ 0.271789] pnp 00:06: [irq 13] > [ 0.271836] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active) > [ 0.272026] pnp 00:07: [io 0x03f0-0x03f5] > [ 0.272029] pnp 00:07: [io 0x03f7] > [ 0.272036] pnp 00:07: [irq 6] > [ 0.272039] pnp 00:07: [dma 2] > [ 0.272102] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active) > [ 0.272323] pnp 00:08: [io 0x03f8-0x03ff] > [ 0.272330] pnp 00:08: [irq 4] > [ 0.272416] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active) > [ 0.272894] pnp 00:09: [io 0x0378-0x037f] > [ 0.272897] pnp 00:09: [io 0x0778-0x077b] > [ 0.272904] pnp 00:09: [irq 7] > [ 0.272907] pnp 00:09: [dma 3] > [ 0.272984] pnp 00:09: Plug and Play ACPI device, IDs PNP0401 (active) > [ 0.273026] pnp 00:0a: [io 0x0060] > [ 0.273028] pnp 00:0a: [io 0x0064] > [ 0.273035] pnp 00:0a: [irq 1] > [ 0.273093] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) > [ 0.273329] pnp 00:0b: [io 0x0330-0x0331] > [ 0.273336] pnp 00:0b: [irq 10] > [ 0.273401] pnp 00:0b: Plug and Play ACPI device, IDs PNPb006 (active) > [ 0.273602] pnp 00:0c: [io 0x0201] > [ 0.273657] pnp 00:0c: Plug and Play ACPI device, IDs PNPb02f (active) > [ 0.273678] pnp 00:0d: [mem 0xe0000000-0xefffffff] > [ 0.273754] system 00:0d: [mem 0xe0000000-0xefffffff] has been reserved > [ 0.273758] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active) > [ 0.273885] pnp 00:0e: [mem 0x000da000-0x000dbfff] > [ 0.273888] pnp 00:0e: [mem 0x000f0000-0x000f7fff] > [ 0.273890] pnp 00:0e: [mem 0x000f8000-0x000fbfff] > [ 0.273893] pnp 00:0e: [mem 0x000fc000-0x000fffff] > [ 0.273896] pnp 00:0e: [mem 0xbfff0000-0xbfffffff] > [ 0.273899] pnp 00:0e: [mem 0xffff0000-0xffffffff] > [ 0.273901] pnp 00:0e: [mem 0x00000000-0x0009ffff] > [ 0.273904] pnp 00:0e: [mem 0x00100000-0xbffeffff] > [ 0.273907] pnp 00:0e: [mem 0xfec00000-0xfec00fff] > [ 0.273910] pnp 00:0e: [mem 0xfee00000-0xfeefffff] > [ 0.273916] pnp 00:0e: [mem 0xfefff000-0xfeffffff] > [ 0.273919] pnp 00:0e: [mem 0xfff80000-0xfff80fff] > [ 0.273921] pnp 00:0e: [mem 0xfff90000-0xfffbffff] > [ 0.273924] pnp 00:0e: [mem 0xfffed000-0xfffeffff] > [ 0.274012] system 00:0e: [mem 0x000da000-0x000dbfff] has been reserved > [ 0.274015] system 00:0e: [mem 0x000f0000-0x000f7fff] could not be reserved > [ 0.274019] system 00:0e: [mem 0x000f8000-0x000fbfff] could not be reserved > [ 0.274022] system 00:0e: [mem 0x000fc000-0x000fffff] could not be reserved > [ 0.274026] system 00:0e: [mem 0xbfff0000-0xbfffffff] could not be reserved > [ 0.274030] system 00:0e: [mem 0xffff0000-0xffffffff] has been reserved > [ 0.274033] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved > [ 0.274036] system 00:0e: [mem 0x00100000-0xbffeffff] could not be reserved > [ 0.274040] system 00:0e: [mem 0xfec00000-0xfec00fff] could not be reserved > [ 0.274044] system 00:0e: [mem 0xfee00000-0xfeefffff] has been reserved > [ 0.274047] system 00:0e: [mem 0xfefff000-0xfeffffff] has been reserved > [ 0.274051] system 00:0e: [mem 0xfff80000-0xfff80fff] has been reserved > [ 0.274054] system 00:0e: [mem 0xfff90000-0xfffbffff] has been reserved > [ 0.274058] system 00:0e: [mem 0xfffed000-0xfffeffff] has been reserved > [ 0.274061] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active) > [ 0.274075] pnp: PnP ACPI: found 15 devices > [ 0.274076] ACPI: ACPI bus type pnp unregistered > [ 0.281006] Switching to clocksource acpi_pm > [ 0.281081] pci 0000:00:02.1: BAR 0: assigned [mem 0xd7104000-0xd71040ff] > [ 0.281087] pci 0000:00:09.0: PCI bridge to [bus 05-05] > [ 0.281090] pci 0000:00:09.0: bridge window [io 0xa000-0xafff] > [ 0.281094] pci 0000:00:09.0: bridge window [mem 0xd5000000-0xd6ffffff] > [ 0.281100] pci 0000:00:0b.0: PCI bridge to [bus 04-04] > [ 0.281102] pci 0000:00:0b.0: bridge window [io 0x9000-0x9fff] > [ 0.281106] pci 0000:00:0b.0: bridge window [mem 0xd3000000-0xd4ffffff] > [ 0.281111] pci 0000:00:0c.0: PCI bridge to [bus 03-03] > [ 0.281115] pci 0000:00:0c.0: bridge window [mem 0xd7000000-0xd70fffff] > [ 0.281120] pci 0000:00:0d.0: PCI bridge to [bus 02-02] > [ 0.281126] pci 0000:00:0e.0: PCI bridge to [bus 01-01] > [ 0.281129] pci 0000:00:0e.0: bridge window [io 0x8000-0x8fff] > [ 0.281133] pci 0000:00:0e.0: bridge window [mem 0xd0000000-0xd2ffffff] > [ 0.281137] pci 0000:00:0e.0: bridge window [mem 0xc0000000-0xcfffffff 64bit pref] > [ 0.281148] pci 0000:00:09.0: setting latency timer to 64 > [ 0.281162] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] > [ 0.281164] pci_bus 0000:00: resource 5 [mem 0xc0000000-0xffffffff] > [ 0.281167] pci_bus 0000:00: resource 6 [mem 0xfeb00000-0xfec0ffff] > [ 0.281170] pci_bus 0000:00: resource 7 [mem 0x000a0000-0x000bffff] > [ 0.281173] pci_bus 0000:00: resource 8 [mem 0x140000000-0xfcffffffff] > [ 0.281177] pci_bus 0000:05: resource 0 [io 0xa000-0xafff] > [ 0.281179] pci_bus 0000:05: resource 1 [mem 0xd5000000-0xd6ffffff] > [ 0.281182] pci_bus 0000:05: resource 4 [io 0x0000-0xffff] > [ 0.281185] pci_bus 0000:05: resource 5 [mem 0xc0000000-0xffffffff] > [ 0.281188] pci_bus 0000:05: resource 6 [mem 0xfeb00000-0xfec0ffff] > [ 0.281191] pci_bus 0000:05: resource 7 [mem 0x000a0000-0x000bffff] > [ 0.281194] pci_bus 0000:05: resource 8 [mem 0x140000000-0xfcffffffff] > [ 0.281197] pci_bus 0000:04: resource 0 [io 0x9000-0x9fff] > [ 0.281200] pci_bus 0000:04: resource 1 [mem 0xd3000000-0xd4ffffff] > [ 0.281203] pci_bus 0000:03: resource 1 [mem 0xd7000000-0xd70fffff] > [ 0.281206] pci_bus 0000:01: resource 0 [io 0x8000-0x8fff] > [ 0.281209] pci_bus 0000:01: resource 1 [mem 0xd0000000-0xd2ffffff] > [ 0.281212] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xcfffffff 64bit pref] > [ 0.281268] NET: Registered protocol family 2 > [ 0.281431] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) > [ 0.283228] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) > [ 0.288907] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > [ 0.289746] TCP: Hash tables configured (established 524288 bind 65536) > [ 0.289750] TCP: reno registered > [ 0.289771] UDP hash table entries: 2048 (order: 4, 65536 bytes) > [ 0.289838] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) > [ 0.290003] NET: Registered protocol family 1 > [ 0.290256] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 > [ 0.360157] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 > [ 0.360244] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360250] pci 0000:00:0b.0: Found disabled HT MSI Mapping > [ 0.360258] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360262] pci 0000:00:0b.0: Linking AER extended capability > [ 0.360300] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360306] pci 0000:00:0c.0: Found disabled HT MSI Mapping > [ 0.360313] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360316] pci 0000:00:0c.0: Linking AER extended capability > [ 0.360356] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360362] pci 0000:00:0d.0: Found disabled HT MSI Mapping > [ 0.360369] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360372] pci 0000:00:0d.0: Linking AER extended capability > [ 0.360416] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360422] pci 0000:00:0e.0: Found disabled HT MSI Mapping > [ 0.360430] pci 0000:00:00.0: Found enabled HT MSI Mapping > [ 0.360433] pci 0000:00:0e.0: Linking AER extended capability > [ 0.360449] PCI: CLS mismatch (32 != 4), using 64 bytes > [ 0.360537] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 > [ 0.360592] pci 0000:01:00.0: Boot video device > [ 0.360673] Trying to unpack rootfs image as initramfs... > [ 0.846792] Freeing initrd memory: 20436k freed > [ 0.865555] PCI-DMA: Disabling AGP. > [ 0.865714] PCI-DMA: aperture base @ b4000000 size 65536 KB > [ 0.865716] PCI-DMA: using GART IOMMU. > [ 0.865720] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture > [ 0.870936] audit: initializing netlink socket (disabled) > [ 0.870962] type=2000 audit(1343003169.868:1): initialized > [ 0.897856] HugeTLB registered 2 MB page size, pre-allocated 0 pages > [ 0.900600] VFS: Disk quotas dquot_6.5.2 > [ 0.900663] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > [ 0.901318] fuse init (API version 7.19) > [ 0.901440] msgmni has been set to 7647 > [ 0.902080] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) > [ 0.902135] io scheduler noop registered > [ 0.902138] io scheduler deadline registered > [ 0.902175] io scheduler cfq registered (default) > [ 0.902389] pcieport 0000:00:0b.0: irq 40 for MSI/MSI-X > [ 0.902520] pcieport 0000:00:0c.0: irq 41 for MSI/MSI-X > [ 0.902633] pcieport 0000:00:0d.0: irq 42 for MSI/MSI-X > [ 0.902742] pcieport 0000:00:0e.0: irq 43 for MSI/MSI-X > [ 0.902823] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 0.902850] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > [ 0.903012] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 > [ 0.903019] ACPI: Power Button [PWRB] > [ 0.903084] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 > [ 0.903090] ACPI: Power Button [PWRF] > [ 0.903153] ACPI: Fan [FAN] (on) > [ 0.908614] thermal LNXTHERM:00: registered as thermal_zone0 > [ 0.908616] ACPI: Thermal Zone [THRM] (40 C) > [ 0.908656] GHES: HEST is not enabled! > [ 0.908781] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled > [ 0.929087] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 0.950987] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 0.951305] Linux agpgart interface v0.103 > [ 0.953255] brd: module loaded > [ 0.954292] loop: module loaded > [ 0.954669] pata_acpi 0000:00:06.0: setting latency timer to 64 > [ 0.955042] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21 > [ 0.955077] pata_acpi 0000:00:07.0: setting latency timer to 64 > [ 0.955359] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20 > [ 0.955394] pata_acpi 0000:00:08.0: setting latency timer to 64 > [ 0.955939] Fixed MDIO Bus: probed > [ 0.955959] tun: Universal TUN/TAP device driver, 1.6 > [ 0.955961] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> > [ 0.956047] PPP generic driver version 2.4.2 > [ 0.956199] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > [ 0.956202] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 > [ 0.956291] ehci_hcd 0000:00:02.1: setting latency timer to 64 > [ 0.956295] ehci_hcd 0000:00:02.1: EHCI Host Controller > [ 0.956406] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 > [ 0.956416] ehci_hcd 0000:00:02.1: reset hcs_params 0x10148a dbg=1 cc=1 pcc=4 !ppc ports=10 > [ 0.956426] ehci_hcd 0000:00:02.1: reset portroute 0 0 0 0 0 0 0 0 0 0 > [ 0.956429] ehci_hcd 0000:00:02.1: reset hcc_params a086 caching frame 256/512/1024 park > [ 0.956466] ehci_hcd 0000:00:02.1: park 0 > [ 0.956472] ehci_hcd 0000:00:02.1: debug port 1 > [ 0.956477] ehci_hcd 0000:00:02.1: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT > [ 0.956481] ehci_hcd 0000:00:02.1: bogus port configuration: cc=1 x pcc=4 < ports=10 > [ 0.956486] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported > [ 0.956489] ehci_hcd 0000:00:02.1: supports USB remote wakeup > [ 0.956516] ehci_hcd 0000:00:02.1: irq 22, io mem 0xd7104000 > [ 0.956521] ehci_hcd 0000:00:02.1: init command 0010005 (park)=0 ithresh=1 period=512 RUN > [ 0.968025] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00 > [ 0.968065] usb usb1: default language 0x0409 > [ 0.968074] usb usb1: udev 1, busnum 1, minor = 0 > [ 0.968077] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > [ 0.968080] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > [ 0.968082] usb usb1: Product: EHCI Host Controller > [ 0.968085] usb usb1: Manufacturer: Linux 3.5.0edje ehci_hcd > [ 0.968088] usb usb1: SerialNumber: 0000:00:02.1 > [ 0.968205] usb usb1: usb_probe_device > [ 0.968210] usb usb1: configuration #1 chosen from 1 choice > [ 0.968222] usb usb1: adding 1-0:1.0 (config #1, interface 0) > [ 0.968250] hub 1-0:1.0: usb_probe_interface > [ 0.968253] hub 1-0:1.0: usb_probe_interface - got id > [ 0.968257] hub 1-0:1.0: USB hub found > [ 0.968263] hub 1-0:1.0: 10 ports detected > [ 0.968266] hub 1-0:1.0: standalone hub > [ 0.968269] hub 1-0:1.0: no power switching (usb 1.0) > [ 0.968271] hub 1-0:1.0: individual port over-current protection > [ 0.968274] hub 1-0:1.0: power on to power good time: 20ms > [ 0.968280] hub 1-0:1.0: local power source is good > [ 0.968283] hub 1-0:1.0: trying to enable port power on non-switchable hub > [ 0.968415] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > [ 0.968418] ohci_hcd: block sizes: ed 80 td 96 > [ 0.968499] ohci_hcd 0000:00:02.0: setting latency timer to 64 > [ 0.968502] ohci_hcd 0000:00:02.0: OHCI Host Controller > [ 0.968568] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 > [ 0.968586] ohci_hcd 0000:00:02.0: created debug files > [ 0.968588] ohci_hcd 0000:00:02.0: supports USB remote wakeup > [ 0.968606] ohci_hcd 0000:00:02.0: irq 23, io mem 0xd7103000 > [ 1.026012] ohci_hcd 0000:00:02.0: OHCI controller state > [ 1.026016] ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers, rh state running > [ 1.026020] ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3 > [ 1.026023] ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0 > [ 1.026027] ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF > [ 1.026030] ohci_hcd 0000:00:02.0: intrenable 0x8000004a MIE RHSC RD WDH > [ 1.026034] ohci_hcd 0000:00:02.0: hcca frame #0003 > [ 1.026039] ohci_hcd 0000:00:02.0: roothub.a 0100020a POTPGT=1 NPS NDP=10(10) > [ 1.026042] ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000 > [ 1.026046] ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE > [ 1.026050] ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS > [ 1.026053] ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS > [ 1.026057] ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS > [ 1.026061] ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS > [ 1.026065] ohci_hcd 0000:00:02.0: roothub.portstatus [4] 0x00000100 PPS > [ 1.026068] ohci_hcd 0000:00:02.0: roothub.portstatus [5] 0x00000100 PPS > [ 1.026072] ohci_hcd 0000:00:02.0: roothub.portstatus [6] 0x00000100 PPS > [ 1.026076] ohci_hcd 0000:00:02.0: roothub.portstatus [7] 0x00000100 PPS > [ 1.026080] ohci_hcd 0000:00:02.0: roothub.portstatus [8] 0x00000100 PPS > [ 1.026084] ohci_hcd 0000:00:02.0: roothub.portstatus [9] 0x00000100 PPS > [ 1.026099] usb usb2: default language 0x0409 > [ 1.026107] usb usb2: udev 1, busnum 2, minor = 128 > [ 1.026110] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 > [ 1.026113] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > [ 1.026115] usb usb2: Product: OHCI Host Controller > [ 1.026118] usb usb2: Manufacturer: Linux 3.5.0edje ohci_hcd > [ 1.026120] usb usb2: SerialNumber: 0000:00:02.0 > [ 1.026219] usb usb2: usb_probe_device > [ 1.026223] usb usb2: configuration #1 chosen from 1 choice > [ 1.026231] usb usb2: adding 2-0:1.0 (config #1, interface 0) > [ 1.026254] hub 2-0:1.0: usb_probe_interface > [ 1.026257] hub 2-0:1.0: usb_probe_interface - got id > [ 1.026261] hub 2-0:1.0: USB hub found > [ 1.026267] hub 2-0:1.0: 10 ports detected > [ 1.026270] hub 2-0:1.0: standalone hub > [ 1.026272] hub 2-0:1.0: no power switching (usb 1.0) > [ 1.026274] hub 2-0:1.0: global over-current protection > [ 1.026276] hub 2-0:1.0: power on to power good time: 2ms > [ 1.026282] hub 2-0:1.0: local power source is good > [ 1.026285] hub 2-0:1.0: no over-current condition exists > [ 1.026287] hub 2-0:1.0: trying to enable port power on non-switchable hub > [ 1.026352] ehci_hcd 0000:00:02.1: HS companion for 0000:00:02.0 > [ 1.026402] uhci_hcd: USB Universal Host Controller Interface driver > [ 1.026515] xhci_hcd 0000:03:00.0: xHCI Host Controller > [ 1.026589] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 3 > [ 1.026610] xhci_hcd 0000:03:00.0: xHCI capability registers at ffffc9000063c000: > [ 1.026615] xhci_hcd 0000:03:00.0: CAPLENGTH AND HCIVERSION 0x1000020: > [ 1.026617] xhci_hcd 0000:03:00.0: CAPLENGTH: 0x20 > [ 1.026620] xhci_hcd 0000:03:00.0: HCIVERSION: 0x100 > [ 1.026625] xhci_hcd 0000:03:00.0: HCSPARAMS 1: 0x8000820 > [ 1.026627] xhci_hcd 0000:03:00.0: Max device slots: 32 > [ 1.026630] xhci_hcd 0000:03:00.0: Max interrupters: 8 > [ 1.026632] xhci_hcd 0000:03:00.0: Max ports: 8 > [ 1.026637] xhci_hcd 0000:03:00.0: HCSPARAMS 2: 0x24000011 > [ 1.026639] xhci_hcd 0000:03:00.0: Isoc scheduling threshold: 1 > [ 1.026642] xhci_hcd 0000:03:00.0: Maximum allowed segments in event ring: 1 > [ 1.026647] xhci_hcd 0000:03:00.0: HCSPARAMS 3 0x0: > [ 1.026649] xhci_hcd 0000:03:00.0: Worst case U1 device exit latency: 0 > [ 1.026652] xhci_hcd 0000:03:00.0: Worst case U2 device exit latency: 0 > [ 1.026656] xhci_hcd 0000:03:00.0: HCC PARAMS 0x14051cf: > [ 1.026659] xhci_hcd 0000:03:00.0: HC generates 64 bit addresses > [ 1.026661] xhci_hcd 0000:03:00.0: FIXME: more HCCPARAMS debugging > [ 1.026666] xhci_hcd 0000:03:00.0: RTSOFF 0x600: > [ 1.026668] xhci_hcd 0000:03:00.0: xHCI operational registers at ffffc9000063c020: > [ 1.026673] xhci_hcd 0000:03:00.0: USBCMD 0x0: > [ 1.026675] xhci_hcd 0000:03:00.0: HC is being stopped > [ 1.026677] xhci_hcd 0000:03:00.0: HC has finished hard reset > [ 1.026680] xhci_hcd 0000:03:00.0: Event Interrupts disabled > [ 1.026682] xhci_hcd 0000:03:00.0: Host System Error Interrupts disabled > [ 1.026685] xhci_hcd 0000:03:00.0: HC has finished light reset > [ 1.026689] xhci_hcd 0000:03:00.0: USBSTS 0x1: > [ 1.026692] xhci_hcd 0000:03:00.0: Event ring is empty > [ 1.026695] xhci_hcd 0000:03:00.0: No Host System Error > [ 1.026697] xhci_hcd 0000:03:00.0: HC is halted > [ 1.026702] xhci_hcd 0000:03:00.0: ffffc9000063c420 port status reg = 0x80 > [ 1.026707] xhci_hcd 0000:03:00.0: ffffc9000063c424 port power reg = 0x0 > [ 1.026712] xhci_hcd 0000:03:00.0: ffffc9000063c428 port link reg = 0x0 > [ 1.026717] xhci_hcd 0000:03:00.0: ffffc9000063c42c port reserved reg = 0x0 > [ 1.026722] xhci_hcd 0000:03:00.0: ffffc9000063c430 port status reg = 0x80 > [ 1.026727] xhci_hcd 0000:03:00.0: ffffc9000063c434 port power reg = 0x0 > [ 1.026732] xhci_hcd 0000:03:00.0: ffffc9000063c438 port link reg = 0x0 > [ 1.026737] xhci_hcd 0000:03:00.0: ffffc9000063c43c port reserved reg = 0x0 > [ 1.026742] xhci_hcd 0000:03:00.0: ffffc9000063c440 port status reg = 0x80 > [ 1.026747] xhci_hcd 0000:03:00.0: ffffc9000063c444 port power reg = 0x0 > [ 1.026752] xhci_hcd 0000:03:00.0: ffffc9000063c448 port link reg = 0x0 > [ 1.026757] xhci_hcd 0000:03:00.0: ffffc9000063c44c port reserved reg = 0x0 > [ 1.026762] xhci_hcd 0000:03:00.0: ffffc9000063c450 port status reg = 0x80 > [ 1.026767] xhci_hcd 0000:03:00.0: ffffc9000063c454 port power reg = 0x0 > [ 1.026772] xhci_hcd 0000:03:00.0: ffffc9000063c458 port link reg = 0x0 > [ 1.026777] xhci_hcd 0000:03:00.0: ffffc9000063c45c port reserved reg = 0x0 > [ 1.026782] xhci_hcd 0000:03:00.0: ffffc9000063c460 port status reg = 0x80 > [ 1.026787] xhci_hcd 0000:03:00.0: ffffc9000063c464 port power reg = 0x0 > [ 1.026791] xhci_hcd 0000:03:00.0: ffffc9000063c468 port link reg = 0x0 > [ 1.026796] xhci_hcd 0000:03:00.0: ffffc9000063c46c port reserved reg = 0x0 > [ 1.026801] xhci_hcd 0000:03:00.0: ffffc9000063c470 port status reg = 0x80 > [ 1.026806] xhci_hcd 0000:03:00.0: ffffc9000063c474 port power reg = 0x0 > [ 1.026811] xhci_hcd 0000:03:00.0: ffffc9000063c478 port link reg = 0x0 > [ 1.026816] xhci_hcd 0000:03:00.0: ffffc9000063c47c port reserved reg = 0x0 > [ 1.026820] xhci_hcd 0000:03:00.0: ffffc9000063c480 port status reg = 0x80 > [ 1.026825] xhci_hcd 0000:03:00.0: ffffc9000063c484 port power reg = 0x0 > [ 1.026830] xhci_hcd 0000:03:00.0: ffffc9000063c488 port link reg = 0x0 > [ 1.026835] xhci_hcd 0000:03:00.0: ffffc9000063c48c port reserved reg = 0x0 > [ 1.026840] xhci_hcd 0000:03:00.0: ffffc9000063c490 port status reg = 0x80 > [ 1.026845] xhci_hcd 0000:03:00.0: ffffc9000063c494 port power reg = 0x0 > [ 1.026850] xhci_hcd 0000:03:00.0: ffffc9000063c498 port link reg = 0x0 > [ 1.026854] xhci_hcd 0000:03:00.0: ffffc9000063c49c port reserved reg = 0x0 > [ 1.026858] xhci_hcd 0000:03:00.0: // Halt the HC > [ 1.026867] xhci_hcd 0000:03:00.0: Resetting HCD > [ 1.026871] xhci_hcd 0000:03:00.0: // Reset the HC > [ 1.564629] xhci_hcd 0000:03:00.0: can't setup > [ 1.564637] xhci_hcd 0000:03:00.0: USB bus 3 deregistered > [ 1.564776] xhci_hcd 0000:03:00.0: init 0000:03:00.0 fail, -110 > [ 1.564799] xhci_hcd: probe of 0000:03:00.0 failed with error -110 > [ 1.564814] ehci_hcd 0000:00:02.1: GetStatus port:8 status 001403 0 ACK POWER sig=k CSC CONNECT > [ 1.564819] hub 1-0:1.0: port 8: status 0501 change 0001 > [ 1.564851] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0000 > [ 1.564852] usbcore: registered new interface driver libusual > [ 1.564912] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 > [ 1.564915] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp > [ 1.565817] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 1.565946] mousedev: PS/2 mouse device common for all mice > [ 1.566154] rtc_cmos 00:04: RTC can wake from S4 > [ 1.566305] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 > [ 1.566333] rtc0: alarms up to one year, y3k, 242 bytes nvram > [ 1.566447] device-mapper: uevent: version 1.0.3 > [ 1.566551] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@xxxxxxxxxx > [ 1.566563] cpuidle: using governor ladder > [ 1.566565] cpuidle: using governor menu > [ 1.566567] EFI Variables Facility v0.08 2004-May-17 > [ 1.566675] TCP: cubic registered > [ 1.566812] NET: Registered protocol family 10 > [ 1.567063] NET: Registered protocol family 17 > [ 1.567077] Key type dns_resolver registered > [ 1.567277] PM: Hibernation image not present or could not be loaded. > [ 1.567296] registered taskstats version 1 > [ 1.571034] Key type trusted registered > [ 1.574439] Key type encrypted registered > [ 1.578111] Magic number: 4:106:406 > [ 1.578259] rtc_cmos 00:04: setting system clock to 2012-07-23 00:26:11 UTC (1343003171) > [ 1.578268] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ (2 cpu cores) (version 2.20.00) > [ 1.578282] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found. > [ 1.578282] [Firmware Bug]: powernow-k8: Try again with latest BIOS. > [ 1.578320] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > [ 1.578322] EDD information not available. > [ 1.580507] Freeing unused kernel memory: 912k freed > [ 1.581126] Write protecting the kernel read-only data: 12288k > [ 1.587655] Freeing unused kernel memory: 1552k freed > [ 1.589270] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2 > [ 1.593899] Freeing unused kernel memory: 1200k freed > [ 1.626079] udevd[125]: starting version 175 > [ 1.664242] hub 1-0:1.0: state 7 ports 10 chg 0100 evt 0000 > [ 1.664264] hub 1-0:1.0: port 8, status 0501, change 0000, 480 Mb/s > [ 1.664287] ehci_hcd 0000:00:02.1: port 8 low speed --> companion > [ 1.720095] ehci_hcd 0000:00:02.1: GetStatus port:8 status 003402 0 ACK POWER OWNER sig=k CSC > [ 1.720137] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0100 > [ 1.720149] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [7] = 0x00010301 CSC LSDA PPS CCS > [ 1.720155] hub 2-0:1.0: port 8, status 0301, change 0001, 1.5 Mb/s > [ 1.736480] Floppy drive(s): fd0 is 1.44M > [ 1.756057] FDC 0 is a post-1991 82077 > [ 1.770554] pata_amd 0000:00:06.0: version 0.4.1 > [ 1.770656] pata_amd 0000:00:06.0: setting latency timer to 64 > [ 1.773551] scsi0 : pata_amd > [ 1.775276] scsi1 : pata_amd > [ 1.776107] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 > [ 1.776110] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 > [ 1.780159] sata_nv 0000:00:07.0: version 3.5 > [ 1.780288] sata_nv 0000:00:07.0: setting latency timer to 64 > [ 1.784119] scsi2 : sata_nv > [ 1.786542] scsi3 : sata_nv > [ 1.786761] ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 21 > [ 1.786764] ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 21 > [ 1.788621] e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k > [ 1.788627] e1000e: Copyright(c) 1999 - 2012 Intel Corporation. > [ 1.790205] sata_nv 0000:00:08.0: setting latency timer to 64 > [ 1.790751] scsi4 : sata_nv > [ 1.790850] scsi5 : sata_nv > [ 1.791014] ata5: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc400 irq 20 > [ 1.791017] ata6: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc408 irq 20 > [ 1.791212] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. > [ 1.791423] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 > [ 1.791433] forcedeth 0000:00:0a.0: setting latency timer to 64 > [ 1.794910] e1000e 0000:04:00.0: Disabling ASPM L0s L1 > [ 1.795101] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 > [ 1.795278] e1000e 0000:04:00.0: (unregistered net_device): Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode > [ 1.795354] e1000e 0000:04:00.0: irq 44 for MSI/MSI-X > [ 1.795361] e1000e 0000:04:00.0: irq 45 for MSI/MSI-X > [ 1.795368] e1000e 0000:04:00.0: irq 46 for MSI/MSI-X > [ 1.804640] sata_promise 0000:05:07.0: version 2.12 > [ 1.806893] scsi6 : sata_promise > [ 1.807804] scsi7 : sata_promise > [ 1.807964] scsi8 : sata_promise > [ 1.808280] scsi9 : sata_promise > [ 1.808337] ata7: SATA max UDMA/133 mmio m4096@0xd6020000 ata 0xd6020380 irq 17 > [ 1.808340] ata8: SATA max UDMA/133 mmio m4096@0xd6020000 ata 0xd6020280 irq 17 > [ 1.808343] ata9: SATA max UDMA/133 mmio m4096@0xd6020000 ata 0xd6020200 irq 17 > [ 1.808347] ata10: SATA max UDMA/133 mmio m4096@0xd6020000 ata 0xd6020300 irq 17 > [ 1.848044] hub 2-0:1.0: debounce: port 8: total 100ms stable 100ms status 0x301 > [ 1.899314] e1000e 0000:04:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1b:21:d4:7c:d3 > [ 1.899321] e1000e 0000:04:00.0: eth0: Intel(R) PRO/1000 Network Connection > [ 1.899333] e1000e 0000:04:00.0: eth0: MAC: 3, PHY: 8, PBA No: E46981-006 > [ 1.968034] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [7] = 0x00100303 PRSC LSDA PPS PES CCS > [ 2.024034] usb 2-8: new low-speed USB device number 2 using ohci_hcd > [ 2.096023] ata3: SATA link down (SStatus 0 SControl 300) > [ 2.116467] ata1.00: ATA-6: ST3200822A, 3.01, max UDMA/100 > [ 2.116471] ata1.00: 390721968 sectors, multi 1: LBA48 > [ 2.118054] ata1.01: ATA-7: Maxtor 6L250R0, BAJ41G20, max UDMA/133 > [ 2.118056] ata1.01: 490234752 sectors, multi 1: LBA48 > [ 2.118065] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6c7c600) ACPI=0x3f01f (20:15:0x1f) > [ 2.118071] ata1: nv_mode_filter: 0x7f39f&0x7f39f->0x7f39f, BIOS=0x7f000 (0xc6c7c600) ACPI=0x7f01f (20:15:0x1f) > [ 2.132341] ata1.00: configured for UDMA/100 > [ 2.144020] ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [7] = 0x00100303 PRSC LSDA PPS PES CCS > [ 2.149738] ata1.01: configured for UDMA/133 > [ 2.149962] scsi 0:0:0:0: Direct-Access ATA ST3200822A 3.01 PQ: 0 ANSI: 5 > [ 2.150202] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 2.150224] sd 0:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB) > [ 2.150287] sd 0:0:0:0: [sda] Write Protect is off > [ 2.150291] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 2.150350] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 2.187139] sda: sda1 sda2 sda3 sda4 < sda5 > > [ 2.187725] sd 0:0:0:0: [sda] Attached SCSI disk > [ 2.187891] scsi 0:0:1:0: Direct-Access ATA Maxtor 6L250R0 BAJ4 PQ: 0 ANSI: 5 > [ 2.188142] sd 0:0:1:0: [sdb] 490234752 512-byte logical blocks: (251 GB/233 GiB) > [ 2.188151] sd 0:0:1:0: Attached scsi generic sg1 type 0 > [ 2.188210] sd 0:0:1:0: [sdb] Write Protect is off > [ 2.188214] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > [ 2.188239] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 2.211033] sdb: sdb1 > [ 2.211456] sd 0:0:1:0: [sdb] Attached SCSI disk > [ 2.227044] usb 2-8: skipped 1 descriptor after interface > [ 2.230042] usb 2-8: default language 0x0409 > [ 2.236044] usb 2-8: udev 2, busnum 2, minor = 129 > [ 2.236048] usb 2-8: New USB device found, idVendor=046d, idProduct=c018 > [ 2.236051] usb 2-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 > [ 2.236054] usb 2-8: Product: USB Optical Mouse > [ 2.236056] usb 2-8: Manufacturer: Logitech > [ 2.236159] usb 2-8: usb_probe_device > [ 2.236163] usb 2-8: configuration #1 chosen from 1 choice > [ 2.239053] usb 2-8: adding 2-8:1.0 (config #1, interface 0) > [ 2.239137] hub 1-0:1.0: state 7 ports 10 chg 0000 evt 0100 > [ 2.239150] ehci_hcd 0000:00:02.1: GetStatus port:8 status 003402 0 ACK POWER OWNER sig=k CSC > [ 2.239157] hub 1-0:1.0: port 8, status 0100, change 0001, 12 Mb/s > [ 2.256044] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 2.264291] ata5.00: ATA-7: HDT722525DLA380, V44OA80A, max UDMA/133 > [ 2.264295] ata5.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 0/32) > [ 2.280275] ata5.00: configured for UDMA/133 > [ 2.284048] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > [ 2.292352] ata7.00: ATA-7: SAMSUNG HD103UJ, 1AA01118, max UDMA7 > [ 2.292355] ata7.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) > [ 2.300350] ata7.00: configured for UDMA/133 > [ 2.316426] forcedeth 0000:00:0a.0: ifname eth1, PHY OUI 0x5043 @ 9, addr 00:15:f2:7b:af:18 > [ 2.316430] forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3 > [ 2.352375] ata2.00: ATA-7: SAMSUNG SP2514N, VF100-41, max UDMA/100 > [ 2.352378] ata2.00: 488397168 sectors, multi 1: LBA48 > [ 2.352386] ata2: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6c7c600) ACPI=0x3f01f (20:600:0x13) > [ 2.352388] ata2.00: limited to UDMA/33 due to 40-wire cable > [ 2.364021] hub 1-0:1.0: debounce: port 8: total 100ms stable 100ms status 0x100 > [ 2.364031] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0100 > [ 2.384299] ata2.00: configured for UDMA/33 > [ 2.384508] scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2514N VF10 PQ: 0 ANSI: 5 > [ 2.384725] sd 1:0:0:0: [sdc] 488397168 512-byte logical blocks: (250 GB/232 GiB) > [ 2.384742] sd 1:0:0:0: Attached scsi generic sg2 type 0 > [ 2.384784] sd 1:0:0:0: [sdc] Write Protect is off > [ 2.384788] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00 > [ 2.384885] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 2.390430] sdc: sdc1 > [ 2.390839] sd 1:0:0:0: [sdc] Attached SCSI disk > [ 2.696028] ata4: SATA link down (SStatus 0 SControl 300) > [ 2.696233] scsi 4:0:0:0: Direct-Access ATA HDT722525DLA380 V44O PQ: 0 ANSI: 5 > [ 2.696470] sd 4:0:0:0: [sdd] 488397168 512-byte logical blocks: (250 GB/232 GiB) > [ 2.696476] sd 4:0:0:0: Attached scsi generic sg3 type 0 > [ 2.696547] sd 4:0:0:0: [sdd] Write Protect is off > [ 2.696551] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 > [ 2.696592] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 2.710249] sdd: sdd1 > [ 2.710678] sd 4:0:0:0: [sdd] Attached SCSI disk > [ 3.164031] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 3.212130] ata6.00: ATAPI: TSSTcorpCD/DVDW SH-W163A, TS00, max UDMA/33 > [ 3.212136] ata6.00: applying bridge limits > [ 3.268120] ata6.00: configured for UDMA/33 > [ 3.269887] scsi 5:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-W163A TS00 PQ: 0 ANSI: 5 > [ 3.277567] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray > [ 3.277570] cdrom: Uniform CD-ROM driver Revision: 3.20 > [ 3.277748] sr 5:0:0:0: Attached scsi CD-ROM sr0 > [ 3.277937] sr 5:0:0:0: Attached scsi generic sg4 type 5 > [ 3.278167] scsi 6:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5 > [ 3.278357] sd 6:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) > [ 3.278376] sd 6:0:0:0: Attached scsi generic sg5 type 0 > [ 3.278429] sd 6:0:0:0: [sde] Write Protect is off > [ 3.278433] sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00 > [ 3.278459] sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 3.302407] sde: sde1 > [ 3.302753] sd 6:0:0:0: [sde] Attached SCSI disk > [ 3.752049] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > [ 3.760368] ata8.00: ATA-7: SAMSUNG HD103UJ, 1AA01118, max UDMA7 > [ 3.760371] ata8.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) > [ 3.768363] ata8.00: configured for UDMA/133 > [ 3.768526] scsi 7:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5 > [ 3.768767] sd 7:0:0:0: Attached scsi generic sg6 type 0 > [ 3.768810] sd 7:0:0:0: [sdf] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) > [ 3.769019] sd 7:0:0:0: [sdf] Write Protect is off > [ 3.769022] sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00 > [ 3.769047] sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 3.793791] sdf: sdf1 > [ 3.794103] sd 7:0:0:0: [sdf] Attached SCSI disk > [ 4.244047] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > [ 4.252364] ata9.00: ATA-7: SAMSUNG HD103UJ, 1AA01118, max UDMA7 > [ 4.252367] ata9.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) > [ 4.260353] ata9.00: configured for UDMA/133 > [ 4.260497] scsi 8:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5 > [ 4.260651] sd 8:0:0:0: [sdg] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) > [ 4.260692] sd 8:0:0:0: Attached scsi generic sg7 type 0 > [ 4.260700] sd 8:0:0:0: [sdg] Write Protect is off > [ 4.260704] sd 8:0:0:0: [sdg] Mode Sense: 00 3a 00 00 > [ 4.260726] sd 8:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 4.283533] sdg: sdg1 > [ 4.283881] sd 8:0:0:0: [sdg] Attached SCSI disk > [ 4.736048] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > [ 4.744364] ata10.00: ATA-7: SAMSUNG SP2504C, VT100-50, max UDMA7 > [ 4.744367] ata10.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32) > [ 4.776359] ata10.00: configured for UDMA/133 > [ 4.776502] scsi 9:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5 > [ 4.776666] sd 9:0:0:0: [sdh] 488397168 512-byte logical blocks: (250 GB/232 GiB) > [ 4.776711] sd 9:0:0:0: Attached scsi generic sg8 type 0 > [ 4.776734] sd 9:0:0:0: [sdh] Write Protect is off > [ 4.776739] sd 9:0:0:0: [sdh] Mode Sense: 00 3a 00 00 > [ 4.776760] sd 9:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 4.780237] usbhid 2-8:1.0: usb_probe_interface > [ 4.780248] usbhid 2-8:1.0: usb_probe_interface - got id > [ 4.780629] sdh: sdh1 > [ 4.781084] sd 9:0:0:0: [sdh] Attached SCSI disk > [ 4.786626] usbcore: registered new interface driver usbhid > [ 4.786631] usbhid: USB HID core driver > [ 4.808133] hub 1-0:1.0: hub_suspend > [ 4.808153] usb usb1: bus auto-suspend, wakeup 1 > [ 4.808157] ehci_hcd 0000:00:02.1: suspend root hub > [ 4.925012] md: bind<sdg1> > [ 4.935939] md: bind<sdc1> > [ 4.950882] md: bind<sdd1> > [ 4.954774] md: bind<sdf1> > [ 4.959208] md: bind<sdh1> > [ 4.963982] async_tx: api initialized (async) > [ 5.032036] raid6: sse2x1 610 MB/s > [ 5.100074] raid6: sse2x2 900 MB/s > [ 5.168056] raid6: sse2x4 1195 MB/s > [ 5.168058] raid6: using algorithm sse2x4 (1195 MB/s) > [ 5.168060] raid6: using intx1 recovery algorithm > [ 5.168845] xor: automatically using best checksumming function: > [ 5.208012] generic_sse: 6580.000 MB/sec > [ 5.209255] md: raid6 personality registered for level 6 > [ 5.209260] md: raid5 personality registered for level 5 > [ 5.209262] md: raid4 personality registered for level 4 > [ 5.209516] bio: create slab <bio-1> at 1 > [ 5.209537] md/raid:md99: device sdh1 operational as raid disk 1 > [ 5.209539] md/raid:md99: device sdd1 operational as raid disk 0 > [ 5.209541] md/raid:md99: device sdc1 operational as raid disk 2 > [ 5.210012] md/raid:md99: allocated 3280kB > [ 5.210102] md/raid:md99: raid level 5 active with 3 out of 3 devices, algorithm 2 > [ 5.210106] RAID conf printout: > [ 5.210108] --- level:5 rd:3 wd:3 > [ 5.210111] disk 0, o:1, dev:sdd1 > [ 5.210113] disk 1, o:1, dev:sdh1 > [ 5.210116] disk 2, o:1, dev:sdc1 > [ 5.210150] md99: detected capacity change from 0 to 500113211392 > [ 5.213573] md: bind<sde1> > [ 5.214410] md99: unknown partition table > [ 5.218448] md/raid:md1: device sde1 operational as raid disk 0 > [ 5.218455] md/raid:md1: device sdf1 operational as raid disk 1 > [ 5.218457] md/raid:md1: device sdg1 operational as raid disk 2 > [ 5.218882] md/raid:md1: allocated 3280kB > [ 5.218952] md/raid:md1: raid level 5 active with 3 out of 3 devices, algorithm 2 > [ 5.218957] RAID conf printout: > [ 5.218959] --- level:5 rd:3 wd:3 > [ 5.218962] disk 0, o:1, dev:sde1 > [ 5.218964] disk 1, o:1, dev:sdf1 > [ 5.218966] disk 2, o:1, dev:sdg1 > [ 5.219004] md1: detected capacity change from 0 to 2000404348928 > [ 5.222208] md1: unknown partition table > [ 6.638576] md: linear personality registered for level -1 > [ 6.641230] md: multipath personality registered for level -4 > [ 6.643739] md: raid0 personality registered for level 0 > [ 6.646500] md: raid1 personality registered for level 1 > [ 6.656653] md: raid10 personality registered for level 10 > [ 6.766896] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) > [ 22.223105] udevd[641]: starting version 175 > [ 22.341494] Adding 963864k swap on /dev/sda5. Priority:-1 extents:1 across:963864k > [ 22.720920] parport_pc 00:09: reported by Plug and Play ACPI > [ 22.720985] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] > [ 22.764792] lp: driver loaded but no devices found > [ 22.800755] lp0: using parport0 (interrupt-driven). > [ 23.052466] MCE: In-kernel MCE decoding enabled. > [ 23.083142] EDAC MC: Ver: 2.1.0 > [ 23.112232] AMD64 EDAC driver v3.4.0 > [ 23.126415] EDAC amd64: DRAM ECC disabled. > [ 23.126436] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load. > [ 23.126436] Either enable ECC checking or force module loading by setting 'ecc_enable_override'. > [ 23.126436] (Note that use of the override may cause unknown side effects.) > [ 23.191502] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-8/2-8:1.0/input/input3 > [ 23.191997] hid-generic 0003:046D:C018.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:02.0-8/input0 > [ 23.444700] microcode: AMD CPU family 0xf not supported > [ 23.446189] i2c i2c-0: nForce2 SMBus adapter at 0x4c00 > [ 23.446227] i2c i2c-1: nForce2 SMBus adapter at 0x4c40 > [ 23.598024] type=1400 audit(1342995993.515:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=716 comm="apparmor_parser" > [ 23.598110] type=1400 audit(1342995993.515:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=716 comm="apparmor_parser" > [ 23.598175] type=1400 audit(1342995993.515:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=716 comm="apparmor_parser" > [ 23.724036] gameport gameport0: NS558 PnP Gameport is pnp00:0c/gameport0, io 0x201, speed 893kHz > [ 23.754849] type=1400 audit(1342995993.671:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=737 comm="apparmor_parser" > [ 23.754985] type=1400 audit(1342995993.671:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=737 comm="apparmor_parser" > [ 23.755059] type=1400 audit(1342995993.671:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=737 comm="apparmor_parser" > [ 23.999155] ppdev: user-space parallel port driver > [ 24.821339] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 > [ 24.943529] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 > [ 24.943559] hda_intel: Disabling MSI > [ 24.943588] hda-intel: 0000:01:00.1: Handle VGA-switcheroo audio client > [ 25.055243] nvidia: module license 'NVIDIA' taints kernel. > [ 25.055250] Disabling lock debugging due to kernel taint > [ 25.104780] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro > [ 25.901713] kjournald starting. Commit interval 5 seconds > [ 25.901877] EXT3-fs (md99): warning: checktime reached, running e2fsck is recommended > [ 25.921911] EXT3-fs (md99): using internal journal > [ 25.921914] EXT3-fs (md99): mounted filesystem with ordered data mode > [ 26.035918] init: failsafe main process (1192) killed by TERM signal > [ 26.120195] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:0e.0/0000:01:00.1/sound/card2/input4 > [ 26.120325] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:0e.0/0000:01:00.1/sound/card2/input5 > [ 26.120400] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:0e.0/0000:01:00.1/sound/card2/input6 > [ 26.120472] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:0e.0/0000:01:00.1/sound/card2/input7 > [ 26.127355] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem > [ 26.130248] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 302.17 Tue Jun 12 16:03:22 PDT 2012 > [ 26.273561] Bluetooth: Core ver 2.16 > [ 26.273596] NET: Registered protocol family 31 > [ 26.273598] Bluetooth: HCI device and connection manager initialized > [ 26.273601] Bluetooth: HCI socket layer initialized > [ 26.273603] Bluetooth: L2CAP socket layer initialized > [ 26.273610] Bluetooth: SCO socket layer initialized > [ 26.304393] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > [ 26.304398] Bluetooth: BNEP filters: protocol multicast > [ 26.328090] Bluetooth: RFCOMM TTY layer initialized > [ 26.328101] Bluetooth: RFCOMM socket layer initialized > [ 26.328104] Bluetooth: RFCOMM ver 1.11 > [ 26.349965] init: udev-fallback-graphics main process (1257) terminated with status 1 > [ 26.396237] forcedeth 0000:00:0a.0: eth1: no link during initialization > [ 26.397300] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready > [ 26.477414] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 27.424314] type=1400 audit(1342995997.342:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1266 comm="apparmor_parser" > [ 27.424528] type=1400 audit(1342995997.342:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1266 comm="apparmor_parser" > [ 27.566714] type=1400 audit(1342995997.482:10): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1298 comm="apparmor_parser" > [ 27.566900] type=1400 audit(1342995997.482:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1298 comm="apparmor_parser" > [ 28.172983] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx > [ 28.172993] e1000e 0000:04:00.0: eth0: 10/100 speed: disabling TSO > [ 28.173833] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 29.008962] vboxdrv: Found 2 processor cores. > [ 29.009297] vboxdrv: fAsync=1 offMin=0x29ee7 offMax=0x29ee7 > [ 29.009417] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'. > [ 29.009419] vboxdrv: Successfully loaded version 4.1.18 (interface 0x00190000). > [ 29.260691] vboxpci: IOMMU not found (not registered) > [ 30.126486] NVRM: Your system is not currently configured to drive a VGA console > [ 30.126493] NVRM: on the primary VGA device. The NVIDIA Linux graphics driver > [ 30.126496] NVRM: requires the use of a text-mode VGA console. Use of other console > [ 30.126498] NVRM: drivers including, but not limited to, vesafb, may result in > [ 30.126500] NVRM: corruption and stability problems, and is not supported. > [ 60.903158] audit_printk_skb: 18 callbacks suppressed > [ 60.903164] type=1400 audit(1342996029.187:18): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=1305 comm="cupsd" pid=1305 comm="cupsd" capability=36 capname="block_suspend" > [ 121.863581] type=1400 audit(1342996090.146:19): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=1305 comm="cupsd" pid=1305 comm="cupsd" capability=36 capname="block_suspend" > [ 285.548387] usb usb1: usb wakeup-resume > [ 285.548396] usb usb1: usb auto-resume > [ 285.548400] ehci_hcd 0000:00:02.1: resume root hub > [ 285.600025] hub 1-0:1.0: hub_resume > [ 285.600049] ehci_hcd 0000:00:02.1: GetStatus port:7 status 001803 0 ACK POWER sig=j CSC CONNECT > [ 285.600052] hub 1-0:1.0: port 7: status 0501 change 0001 > [ 285.704058] hub 1-0:1.0: state 7 ports 10 chg 0080 evt 0000 > [ 285.704082] hub 1-0:1.0: port 7, status 0501, change 0000, 480 Mb/s > [ 285.760264] ehci_hcd 0000:00:02.1: port 7 reset complete, port enabled > [ 285.760271] ehci_hcd 0000:00:02.1: GetStatus port:7 status 001005 0 ACK POWER sig=se0 PE CONNECT > [ 285.816032] usb 1-7: new high-speed USB device number 3 using ehci_hcd > [ 285.872248] ehci_hcd 0000:00:02.1: port 7 reset complete, port enabled > [ 285.872254] ehci_hcd 0000:00:02.1: GetStatus port:7 status 001005 0 ACK POWER sig=se0 PE CONNECT > [ 285.949437] usb 1-7: default language 0x0409 > [ 285.953687] usb 1-7: udev 3, busnum 1, minor = 2 > [ 285.953690] usb 1-7: New USB device found, idVendor=13fe, idProduct=3e00 > [ 285.953693] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > [ 285.953696] usb 1-7: Product: USB DISK 2.0 > [ 285.953698] usb 1-7: Manufacturer: > [ 285.953701] usb 1-7: SerialNumber: 07BB150855FA3DE4 > [ 285.953862] usb 1-7: usb_probe_device > [ 285.953866] usb 1-7: configuration #1 chosen from 1 choice > [ 285.953938] usb 1-7: adding 1-7:1.0 (config #1, interface 0) > [ 285.953976] libusual 1-7:1.0: usb_probe_interface > [ 285.953983] libusual 1-7:1.0: usb_probe_interface - got id > [ 286.009812] Initializing USB Mass Storage driver... > [ 286.009866] usb-storage 1-7:1.0: usb_probe_interface > [ 286.009875] usb-storage 1-7:1.0: usb_probe_interface - got id > [ 286.010042] scsi10 : usb-storage 1-7:1.0 > [ 286.010154] usbcore: registered new interface driver usb-storage > [ 286.010156] USB Mass Storage support registered. > [ 286.029728] usbcore: registered new interface driver uas > [ 287.089363] scsi 10:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 > [ 287.090261] sd 10:0:0:0: Attached scsi generic sg9 type 0 > [ 288.016844] sd 10:0:0:0: [sdi] 30283008 512-byte logical blocks: (15.5 GB/14.4 GiB) > [ 288.017955] sd 10:0:0:0: [sdi] Write Protect is off > [ 288.017959] sd 10:0:0:0: [sdi] Mode Sense: 23 00 00 00 > [ 288.018955] sd 10:0:0:0: [sdi] No Caching mode page present > [ 288.018959] sd 10:0:0:0: [sdi] Assuming drive cache: write through > [ 288.023961] sd 10:0:0:0: [sdi] No Caching mode page present > [ 288.023968] sd 10:0:0:0: [sdi] Assuming drive cache: write through > [ 288.044601] sdi: sdi1 > [ 288.049958] sd 10:0:0:0: [sdi] No Caching mode page present > [ 288.049967] sd 10:0:0:0: [sdi] Assuming drive cache: write through > [ 288.049970] sd 10:0:0:0: [sdi] Attached SCSI removable disk > 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3) > Subsystem: ASUSTeK Computer Inc. A8N-E Mainboard > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > > 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > > 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin A routed to IRQ 3 > Region 0: I/O ports at dc00 [size=32] > Region 4: I/O ports at 4c00 [size=64] > Region 5: I/O ports at 4c40 [size=64] > Capabilities: <access denied> > Kernel driver in use: nForce2_smbus > > 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at d5103000 (32-bit, non-prefetchable) [size=4K] > Capabilities: <access denied> > Kernel driver in use: ohci_hcd > > 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin B routed to IRQ 22 > Region 0: Memory at d5104000 (32-bit, non-prefetchable) [size=256] > Capabilities: <access denied> > Kernel driver in use: ehci_hcd > > 00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP]) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 (750ns min, 250ns max) > Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] > Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] > Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] > Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] > Region 4: I/O ports at f000 [size=16] > Capabilities: <access denied> > Kernel driver in use: pata_amd > > 00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) > Subsystem: ASUSTeK Computer Inc. A8N-E Mainboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin A routed to IRQ 21 > Region 0: I/O ports at 09f0 [size=8] > Region 1: I/O ports at 0bf0 [size=4] > Region 2: I/O ports at 0970 [size=8] > Region 3: I/O ports at 0b70 [size=4] > Region 4: I/O ports at d800 [size=16] > Region 5: Memory at d5102000 (32-bit, non-prefetchable) [size=4K] > Capabilities: <access denied> > Kernel driver in use: sata_nv > > 00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin A routed to IRQ 20 > Region 0: I/O ports at 09e0 [size=8] > Region 1: I/O ports at 0be0 [size=4] > Region 2: I/O ports at 0960 [size=8] > Region 3: I/O ports at 0b60 [size=4] > Region 4: I/O ports at c400 [size=16] > Region 5: Memory at d5101000 (32-bit, non-prefetchable) [size=4K] > Capabilities: <access denied> > Kernel driver in use: sata_nv > > 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=128 > I/O behind bridge: 0000a000-0000afff > Memory behind bridge: d3000000-d4ffffff > Prefetchable memory behind bridge: fff00000-000fffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- > > 00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3) > Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ > Latency: 0 (250ns min, 5000ns max) > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at d5100000 (32-bit, non-prefetchable) [size=4K] > Region 1: I/O ports at b000 [size=8] > Capabilities: <access denied> > Kernel driver in use: forcedeth > > 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: d5000000-d50fffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: fff00000-000fffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: fff00000-000fffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00009000-00009fff > Memory behind bridge: d0000000-d2ffffff > Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Capabilities: <access denied> > > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Kernel driver in use: k8temp > > 01:00.0 VGA compatible controller: nVidia Corporation GF108 [GeForce GT 430] (rev a1) (prog-if 00 [VGA controller]) > Subsystem: Micro-Star International Co., Ltd. Device 2304 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M] > Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] > Region 3: Memory at c8000000 (64-bit, prefetchable) [size=32M] > Region 5: I/O ports at 9000 [size=128] > Expansion ROM at d1000000 [disabled] [size=512K] > Capabilities: <access denied> > Kernel driver in use: nouveau > > 01:00.1 Audio device: nVidia Corporation GF108 High Definition Audio Controller (rev a1) > Subsystem: Micro-Star International Co., Ltd. Device 2304 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Interrupt: pin B routed to IRQ 19 > Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: snd_hda_intel > > 04:00.0 USB Controller: Renesas Technology Corp. Device 0014 (rev 03) (prog-if 30 [XHCI]) > Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin A routed to IRQ 17 > Region 0: Memory at d5000000 (64-bit, non-prefetchable) [size=8K] > Capabilities: <access denied> > > 05:07.0 Mass storage controller: Promise Technology, Inc. PDC40718 (SATA 300 TX4) (rev 02) > Subsystem: Promise Technology, Inc. PDC40718 (SATA 300 TX4) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 72 (1000ns min, 4500ns max), Cache Line Size: 4 bytes > Interrupt: pin A routed to IRQ 17 > Region 0: I/O ports at a000 [size=128] > Region 2: I/O ports at a400 [size=256] > Region 3: Memory at d4020000 (32-bit, non-prefetchable) [size=4K] > Region 4: Memory at d4000000 (32-bit, non-prefetchable) [size=128K] > Expansion ROM at d3000000 [disabled] [size=32K] > Capabilities: <access denied> > Kernel driver in use: sata_promise > > 05:08.0 Multimedia audio controller: Ensoniq 5880B [AudioPCI] (rev 02) > Subsystem: Ensoniq Creative Sound Blaster AudioPCI128 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort+ <MAbort+ >SERR- <PERR- INTx- > Latency: 32 (3000ns min, 32000ns max) > Interrupt: pin A routed to IRQ 18 > Region 0: I/O ports at a800 [size=64] > Capabilities: <access denied> > Kernel driver in use: snd_ens1371 > -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
