From: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
AM335x uses NOP transceiver driver and need to enable builtin PHY
by writing into usb_ctrl register available in system control
module register space. This is being added at musb glue driver
layer untill a separate system control module driver is available.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
Signed-off-by: Damodar Santhapuri <damodar.santhapuri@xxxxxx>
---
Changes from v1:
- Used platform_get_resource() instead of platform_get_resource_byname()
based on Kishon's comment.
arch/arm/mach-omap2/board-ti8168evm.c | 1 -
arch/arm/mach-omap2/omap_phy_internal.c | 35 ------------
arch/arm/plat-omap/include/plat/usb.h | 5 +-
drivers/usb/musb/musb_dsps.c | 87 +++++++++++++++++++++++++------
4 files changed, 73 insertions(+), 55 deletions(-)
diff --git a/arch/arm/mach-omap2/board-ti8168evm.c b/arch/arm/mach-omap2/board-ti8168evm.c
index d4c8392..0c7c098 100644
--- a/arch/arm/mach-omap2/board-ti8168evm.c
+++ b/arch/arm/mach-omap2/board-ti8168evm.c
@@ -26,7 +26,6 @@
#include <plat/usb.h>
static struct omap_musb_board_data musb_board_data = {
- .set_phy_power = ti81xx_musb_phy_power,
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 500,
diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index d52651a..d80bb16 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -254,38 +254,3 @@ void am35x_set_mode(u8 musb_mode)
omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
}
-
-void ti81xx_musb_phy_power(u8 on)
-{
- void __iomem *scm_base = NULL;
- u32 usbphycfg;
-
- scm_base = ioremap(TI81XX_SCM_BASE, SZ_2K);
- if (!scm_base) {
- pr_err("system control module ioremap failed\n");
- return;
- }
-
- usbphycfg = __raw_readl(scm_base + USBCTRL0);
-
- if (on) {
- if (cpu_is_ti816x()) {
- usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
- usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
- } else if (cpu_is_ti814x()) {
- usbphycfg &= ~(USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN
- | USBPHY_DPINPUT | USBPHY_DMINPUT);
- usbphycfg |= (USBPHY_OTGVDET_EN | USBPHY_OTGSESSEND_EN
- | USBPHY_DPOPBUFCTL | USBPHY_DMOPBUFCTL);
- }
- } else {
- if (cpu_is_ti816x())
- usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
- else if (cpu_is_ti814x())
- usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
-
- }
- __raw_writel(usbphycfg, scm_base + USBCTRL0);
-
- iounmap(scm_base);
-}
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 548a4c8..c2aa4ae 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -95,7 +95,6 @@ extern void am35x_musb_reset(void);
extern void am35x_musb_phy_power(u8 on);
extern void am35x_musb_clear_irq(void);
extern void am35x_set_mode(u8 musb_mode);
-extern void ti81xx_musb_phy_power(u8 on);
/* AM35x */
/* USB 2.0 PHY Control */
@@ -120,8 +119,8 @@ extern void ti81xx_musb_phy_power(u8 on);
#define CONF2_DATPOL (1 << 1)
/* TI81XX specific definitions */
-#define USBCTRL0 0x620
-#define USBSTAT0 0x624
+#define MUSB_USBSS_REV_816X 0x9
+#define MUSB_USBSS_REV_814X 0xb
/* TI816X PHY controls bits */
#define TI816X_USBPHY0_NORMAL_MODE (1 << 0)
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 494772f..72eda64 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -115,9 +115,46 @@ struct dsps_glue {
struct platform_device *musb; /* child musb pdev */
const struct dsps_musb_wrapper *wrp; /* wrapper register offsets */
struct timer_list timer; /* otg_workaround timer */
+ u32 __iomem *usb_ctrl;
+ u8 usbss_rev;
};
/**
+ * musb_dsps_phy_control - phy on/off
+ * @glue: struct dsps_glue *
+ * @on: flag for phy to be switched on or off
+ *
+ * This is to enable the PHY using usb_ctrl register in system control
+ * module space.
+ *
+ * XXX: This function will be removed once we have a seperate driver for
+ * control module
+ */
+static void musb_dsps_phy_control(struct dsps_glue *glue, u8 on)
+{
+ u32 usbphycfg;
+
+ usbphycfg = __raw_readl(glue->usb_ctrl);
+
+ if (on) {
+ if (glue->usbss_rev == MUSB_USBSS_REV_816X) {
+ usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
+ usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
+ } else if (glue->usbss_rev == MUSB_USBSS_REV_814X) {
+ usbphycfg &= ~(USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN
+ | USBPHY_DPINPUT | USBPHY_DMINPUT);
+ usbphycfg |= (USBPHY_OTGVDET_EN | USBPHY_OTGSESSEND_EN
+ | USBPHY_DPOPBUFCTL | USBPHY_DMOPBUFCTL);
+ }
+ } else {
+ if (glue->usbss_rev == MUSB_USBSS_REV_816X)
+ usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
+ else if (glue->usbss_rev == MUSB_USBSS_REV_814X)
+ usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
+ }
+ __raw_writel(usbphycfg, glue->usb_ctrl);
+}
+/**
* dsps_musb_enable - enable interrupts
*/
static void dsps_musb_enable(struct musb *musb)
@@ -363,11 +400,9 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
static int dsps_musb_init(struct musb *musb)
{
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
struct platform_device *pdev = to_platform_device(dev->parent);
struct dsps_glue *glue = platform_get_drvdata(pdev);
const struct dsps_musb_wrapper *wrp = glue->wrp;
- struct omap_musb_board_data *data = plat->board_data;
void __iomem *reg_base = musb->ctrl_base;
u32 rev, val;
int status;
@@ -395,8 +430,7 @@ static int dsps_musb_init(struct musb *musb)
dsps_writel(reg_base, wrp->control, (1 << wrp->reset));
/* Start the on-chip PHY and its PLL. */
- if (data->set_phy_power)
- data->set_phy_power(1);
+ musb_dsps_phy_control(glue, 1);
musb->isr = dsps_interrupt;
@@ -418,8 +452,6 @@ err0:
static int dsps_musb_exit(struct musb *musb)
{
struct device *dev = musb->controller;
- struct musb_hdrc_platform_data *plat = dev->platform_data;
- struct omap_musb_board_data *data = plat->board_data;
struct platform_device *pdev = to_platform_device(dev->parent);
struct dsps_glue *glue = platform_get_drvdata(pdev);
@@ -427,8 +459,7 @@ static int dsps_musb_exit(struct musb *musb)
del_timer_sync(&glue->timer);
/* Shutdown the on-chip PHY and its PLL. */
- if (data->set_phy_power)
- data->set_phy_power(0);
+ musb_dsps_phy_control(glue, 0);
/* NOP driver needs change if supporting dual instance */
usb_put_phy(musb->xceiv);
@@ -460,6 +491,21 @@ static int __devinit dsps_create_musb_pdev(struct dsps_glue *glue, u8 id)
char res_name[10];
int ret;
+ /* get memory resource for usb control register */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2 * id + 2);
+ if (!res) {
+ dev_err(dev, "%s get mem resource failed\n", res_name);
+ ret = -ENODEV;
+ goto err0;
+ }
+
+ glue->usb_ctrl = devm_request_and_ioremap(&pdev->dev, res);
+ if (glue->usb_ctrl == NULL) {
+ dev_err(dev, "Failed to obtain usb_ctrl%d memory\n", id);
+ ret = -ENODEV;
+ goto err0;
+ }
+
/* get memory resource */
sprintf(res_name, "musb%d", id);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name);
@@ -538,6 +584,7 @@ static int __devinit dsps_probe(struct platform_device *pdev)
(struct dsps_musb_wrapper *)id->driver_data;
struct dsps_glue *glue;
struct resource *iomem;
+ u32 __iomem *usbss;
int ret;
/* allocate glue */
@@ -556,6 +603,13 @@ static int __devinit dsps_probe(struct platform_device *pdev)
goto err1;
}
+ usbss = devm_request_and_ioremap(&pdev->dev, iomem);
+ if (usbss == NULL) {
+ dev_err(&pdev->dev, "Failed to obtain usbss memory\n");
+ ret = -ENODEV;
+ goto err1;
+ }
+
glue->dev = &pdev->dev;
glue->wrp = kmemdup(wrp, sizeof(*wrp), GFP_KERNEL);
@@ -582,6 +636,9 @@ static int __devinit dsps_probe(struct platform_device *pdev)
goto err3;
}
+ /* read the usbss revision register */
+ glue->usbss_rev = __raw_readl(usbss);
+
return 0;
err3:
@@ -612,24 +669,22 @@ static int __devexit dsps_remove(struct platform_device *pdev)
#ifdef CONFIG_PM_SLEEP
static int dsps_suspend(struct device *dev)
{
- struct musb_hdrc_platform_data *plat = dev->platform_data;
- struct omap_musb_board_data *data = plat->board_data;
+ struct platform_device *pdev = to_platform_device(dev->parent);
+ struct dsps_glue *glue = platform_get_drvdata(pdev);
/* Shutdown the on-chip PHY and its PLL. */
- if (data->set_phy_power)
- data->set_phy_power(0);
+ musb_dsps_phy_control(glue, 0);
return 0;
}
static int dsps_resume(struct device *dev)
{
- struct musb_hdrc_platform_data *plat = dev->platform_data;
- struct omap_musb_board_data *data = plat->board_data;
+ struct platform_device *pdev = to_platform_device(dev->parent);
+ struct dsps_glue *glue = platform_get_drvdata(pdev);
/* Start the on-chip PHY and its PLL. */
- if (data->set_phy_power)
- data->set_phy_power(1);
+ musb_dsps_phy_control(glue, 1);
return 0;
}
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
