Hi Afzal,
On 05/01/2012 07:19 AM, Afzal Mohammed wrote:
[...]
> +static int gpmc_setup_cs_waitpin(struct gpmc *gpmc, struct gpmc_device *gd,
> + unsigned cs, unsigned conf)
> +{
> + u32 l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
> + unsigned idx = ~0x0;
> + int polarity = 0;
>
> - l = gpmc_read_reg(GPMC_REVISION);
> - printk(KERN_INFO "GPMC revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
> - /* Set smart idle mode and automatic L3 clock gating */
> - l = gpmc_read_reg(GPMC_SYSCONFIG);
> - l &= 0x03 << 3;
> - l |= (0x02 << 3) | (1 << 0);
> - gpmc_write_reg(GPMC_SYSCONFIG, l);
> - gpmc_mem_init();
> + switch (conf & GPMC_WAITPIN_MASK) {
> + case GPMC_WAITPIN_0:
> + idx = GPMC_WAITPIN_IDX0;
> + break;
> + case GPMC_WAITPIN_1:
> + idx = GPMC_WAITPIN_IDX1;
> + break;
> + case GPMC_WAITPIN_2:
> + idx = GPMC_WAITPIN_IDX2;
> + break;
> + case GPMC_WAITPIN_3:
> + idx = GPMC_WAITPIN_IDX3;
> + break;
> + /* no waitpin */
> + case 0:
> + break;
> + default:
> + dev_err(gpmc->dev, "multiple waitpins selected on CS:%u\n", cs);
> + return -EINVAL;
> + break;
> + }
Why not combined case 0 and default? Both are invalid configurations so
just report invalid selection.
>
> - /* initalize the irq_chained */
> - irq = OMAP_GPMC_IRQ_BASE;
> - for (cs = 0; cs < GPMC_CS_NUM; cs++) {
> - irq_set_chip_and_handler(irq, &dummy_irq_chip,
> - handle_simple_irq);
> - set_irq_flags(irq, IRQF_VALID);
> - irq++;
> + switch (conf & GPMC_WAITPIN_POLARITY_MASK) {
> + case GPMC_WAITPIN_ACTIVE_LOW:
> + polarity = LOW;
> + break;
> + case GPMC_WAITPIN_ACTIVE_HIGH:
> + polarity = HIGH;
> + break;
> + /* no waitpin */
> + case 0:
> + break;
> + default:
> + dev_err(gpmc->dev, "waitpin polarity set to low & high\n");
> + return -EINVAL;
> + break;
> }
Again, combine case 0 and default as these are invalid.
>
> - ret = request_irq(gpmc_irq, gpmc_handle_irq, IRQF_SHARED, "gpmc", NULL);
> - if (ret)
> - pr_err("gpmc: irq-%d could not claim: err %d\n",
> - gpmc_irq, ret);
> - return ret;
> + if (idx != ~0x0) {
If you combine the above cases, then you can drop the idx test here.
> + if (gd->have_waitpin) {
> + if (gd->waitpin != idx ||
> + gd->waitpin_polarity != polarity) {
> + dev_err(gpmc->dev, "error: conflict: waitpin %u with polarity %d on device %s.%d\n",
> + gd->waitpin, gd->waitpin_polarity,
> + gd->name, gd->id);
> + return -EBUSY;
> + }
> + } else {
Don't need the else as you are going to return in the above.
> + gd->have_waitpin = true;
> + gd->waitpin = idx;
> + gd->waitpin_polarity = polarity;
> + }
> +
> + l &= ~GPMC_CONFIG1_WAIT_PIN_SEL_MASK;
> + l |= GPMC_CONFIG1_WAIT_PIN_SEL(idx);
> + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, l);
> + } else if (polarity) {
> + dev_err(gpmc->dev, "error: waitpin polarity specified with out wait pin number on device %s.%d\n",
> + gd->name, gd->id);
> + return -EINVAL;
Drop this else-if. The above switch statements will report the bad
configuration. This seems a bit redundant.
Cheers
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
