This series of patches adds the Ozmo USB over WiFi driver to the
driver staging directory. This is a driver for a virtual USB HCD
and uses an L2 network protocol to talk to the device.
This patch adds the driver entry code and a README file with more
details.
Signed-off-by: Chris Kelly <ckelly@xxxxxxxxxxxxxxx>
---
drivers/staging/ozwpan/README | 25 +++++++++++++++
drivers/staging/ozwpan/ozconfig.h | 28 +++++++++++++++++
drivers/staging/ozwpan/ozmain.c | 60 +++++++++++++++++++++++++++++++++++++
3 files changed, 113 insertions(+), 0 deletions(-)
create mode 100644 drivers/staging/ozwpan/README
create mode 100644 drivers/staging/ozwpan/ozconfig.h
create mode 100644 drivers/staging/ozwpan/ozmain.c
diff --git a/drivers/staging/ozwpan/README b/drivers/staging/ozwpan/README
new file mode 100644
index 0000000..bb1a69b
--- /dev/null
+++ b/drivers/staging/ozwpan/README
@@ -0,0 +1,25 @@
+OZWPAN USB Host Controller Driver
+---------------------------------
+This driver is a USB HCD driver that does not have an associated a physical
+device but instead uses Wi-Fi to communicate with the wireless peripheral.
+The USB requests are converted into a layer 2 network protocol and transmitted
+on the network using an ethertype (0x892e) regestered to Ozmo Device Inc.
+This driver is compatible with existing wireless devices that use Ozmo Devices
+technology.
+
+To operate the driver must be bound to a suitable network interface. This can
+be done when the module is loaded (specifying the name of the network interface
+as a paramter - e.g. 'insmod ozwpan g_net_dev=go0') or can be bound after
+loading using an ioctl call. See the ozappif.h file and the ioctls
+OZ_IOCTL_ADD_BINDING and OZ_IOCTL_REMOVE_BINDING.
+
+The devices connect to the host use Wi-Fi Direct so a network card that supports
+Wi-Fi direct is required. A recent version (0.8.x or later) version of the
+wpa_supplicant can be used to setup the network interface to create a persistent
+autonomous group (for older pre-WFD peripherals) or put in a listen state to
+allow group negotiation to occur for more recent devices that support WFD.
+
+The protocol used over the network does not directly mimic the USB bus
+transactions as this would be rather busy and inefficient. Instead the chapter 9
+requests are converted into a request/response pair of messages. (See
+ozprotocol.h for data structures used in the protocol).
diff --git a/drivers/staging/ozwpan/ozconfig.h b/drivers/staging/ozwpan/ozconfig.h
new file mode 100644
index 0000000..a8c9726
--- /dev/null
+++ b/drivers/staging/ozwpan/ozconfig.h
@@ -0,0 +1,28 @@
+/* -----------------------------------------------------------------------------
+ * Copyright (c) 2011 Ozmo Inc
+ * Released under the GNU General Public License Version 2 (GPLv2).
+ * ---------------------------------------------------------------------------*/
+#ifndef _OZCONFIG_H
+#define _OZCONFIG_H
+
+/* #define WANT_DEBUG_KMALLOC */
+/* #define WANT_TRACE */
+#ifdef WANT_TRACE
+#define WANT_VERBOSE_TRACE
+#endif /* #ifdef WANT_TRACE */
+/* #define WANT_URB_PARANOIA */
+
+/* #define WANT_PRE_2_6_39 */
+#define WANT_EVENT_TRACE
+
+/* These defines determine what verbose trace is displayed. */
+#ifdef WANT_VERBOSE_TRACE
+/* #define WANT_TRACE_STREAM */
+/* #define WANT_TRACE_URB */
+/* #define WANT_TRACE_CTRL_DETAIL */
+#define WANT_TRACE_HUB
+/* #define WANT_TRACE_RX_FRAMES */
+/* #define WANT_TRACE_TX_FRAMES */
+#endif /* WANT_VERBOSE_TRACE */
+
+#endif /* _OZCONFIG_H */
diff --git a/drivers/staging/ozwpan/ozmain.c b/drivers/staging/ozwpan/ozmain.c
new file mode 100644
index 0000000..d34242b
--- /dev/null
+++ b/drivers/staging/ozwpan/ozmain.c
@@ -0,0 +1,60 @@
+/* -----------------------------------------------------------------------------
+ * Copyright (c) 2011 Ozmo Inc
+ * Released under the GNU General Public License Version 2 (GPLv2).
+ * -----------------------------------------------------------------------------
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/timer.h>
+#include <linux/sched.h>
+#include <linux/netdevice.h>
+#include <linux/errno.h>
+#include <linux/ieee80211.h>
+#include "ozconfig.h"
+#include "ozpd.h"
+#include "ozproto.h"
+#include "ozcdev.h"
+#include "ozalloc.h"
+#include "oztrace.h"
+#include "ozevent.h"
+/*------------------------------------------------------------------------------
+ * The name of the 802.11 mac device. Empty string is the default value but a
+ * value can be supplied as a parameter to the module. An empty string means
+ * bind to nothing. '*' means bind to all netcards - this includes non-802.11
+ * netcards. Bindings can be added later using an IOCTL.
+ */
+char *g_net_dev = "";
+/*------------------------------------------------------------------------------
+ * Context: process
+ */
+static int __init ozwpan_init(void)
+{
+ oz_event_init();
+ oz_cdev_register();
+ oz_protocol_init(g_net_dev);
+ oz_app_enable(OZ_APPID_USB, 1);
+ oz_apps_init();
+ return 0;
+}
+/*------------------------------------------------------------------------------
+ * Context: process
+ */
+static void __exit ozwpan_exit(void)
+{
+ oz_protocol_term();
+ oz_apps_term();
+ oz_cdev_deregister();
+ oz_trace_leaks();
+ oz_event_term();
+}
+/*------------------------------------------------------------------------------
+ */
+module_param(g_net_dev, charp, S_IRUGO);
+module_init(ozwpan_init);
+module_exit(ozwpan_exit);
+
+MODULE_AUTHOR("Chris Kelly");
+MODULE_DESCRIPTION("Ozmo Devices USB over WiFi hcd driver");
+MODULE_VERSION("1.0.8");
+MODULE_LICENSE("GPL");
+
--
1.7.7.6
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
