Hello,
I'm experiencing a write-test failure with
a WDC MyBook 3TB. Hoping someone may
recognize the issue and perhaps have
some advice.
Briefly
# dd bs=1024k if=/dev/zero of=test oflag=direct
dd: writing `test': Read-only file system
10017+0 records in
10016+0 records out
10502537216 bytes (11 GB) copied, 132.675 s, 79.2 MB/s
verbosity follows, attached below.
Running with CentOS 6 kernel 2.6.32-71.29.1.el6.x86_64
but I've found someone else experiencing the same
problem with latest kernel:
http://forums.gentoo.org/viewtopic.php?p=6871586#6871586
Willing to run the test with current kernel.org
if desired. Same drive works perfectly when
attached to a CentOS 5 system via USB2. Have
trouble tickets open with both WD and Highpoint.
hardware:
USB3 controller: ASMedia ASM1042 USB controller
(Highpoint RocketU 1144A card)
drive: WDBACW0030HBK-00
(WDC MyBook Essential 3TB)
(latest firmware 1016 flashed)
Experienced a generally similar failure when
trying it out with a VIA VL800 USB3 controller
(SYBA card). Messages in 'dmesg' were different.
I find it interesting that the other person
seeing this issue has an Intel USB3 controller
(i.e. reference-implementation hardware). Seems
to reduce the possibility of an issue at the
USB3 layer and point to a higher-layer firmware
or driver issue, perhaps related to timing or
latency.
Any ideas or suggestions will be much appreciated.
Thanks!
P.S. Note that the 'lsusb' output does not include
the drive as it was run later. If it's important
will run it again with the drive attached.
-
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32-71.29.1.el6.x86_64 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.4 20100726 (Red Hat 4.4.4-13) (GCC) ) #1 SMP Mon Jun 27 19:49:27 BST 2011
Command line: ro root=/dev/mapper/vg00-lv00 rd_MD_UUID=173392af:8b21bd50:1ee82f77:7d779ed3 rd_LVM_LV=vg00/lv00 rd_LVM_LV=vg00/lv01 rd_NO_LUKS rd_NO_DM
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ca000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 0000000080000000 - 00000000c7ee0000 (usable)
BIOS-e820: 00000000c7ee0000 - 00000000c7ef4000 (ACPI data)
BIOS-e820: 00000000c7ef4000 - 00000000c7f7f000 (ACPI NVS)
BIOS-e820: 00000000c7f80000 - 00000000c8000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000238000000 (usable)
DMI present.
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x238000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CBFFF write-protect
CC000-DFFFF uncachable
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 0000000000 mask FF80000000 write-back
1 base 0080000000 mask FFC0000000 write-back
2 base 00C0000000 mask FFF8000000 write-back
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
TOM2: 0000000238000000 aka 9088M
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000c8000000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xc7ee0 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000c7ee0000
0000000000 - 00c7e00000 page 2M
00c7e00000 - 00c7ee0000 page 4k
kernel direct mapping tables up to c7ee0000 @ 8000-e000
init_memory_mapping: 0000000100000000-0000000238000000
0100000000 - 0238000000 page 2M
kernel direct mapping tables up to 238000000 @ c000-16000
RAMDISK: 3739e000 - 37fef3a4
ACPI: RSDP 00000000000f79b0 00024 (v02 PTLTD )
ACPI: XSDT 00000000c7eeff28 00094 (v01 DELL PE_SC3 06040000 DELL 00000000)
ACPI: FACP 00000000c7ef36cb 000F4 (v03 DELL PE_SC3 06040000 DELL 000F4240)
ACPI: DSDT 00000000c7eeffbc 0369B (v01 DELL PE_SC3 06040000 MSFT 0100000E)
ACPI: FACS 00000000c7ef4fc0 00040
ACPI: TCPA 00000000c7ef37bf 00032 (v01 Phoeni x 06040000 TL 00000000)
ACPI: SLIC 00000000c7ef37f1 00024 (v01 DELL PE_SC3 06040000 PTL 00000001)
ACPI: SPCR 00000000c7ef3815 00050 (v01 DELL PE_SC3 06040000 PTL 00000001)
ACPI: EINJ 00000000c7ef3865 001B0 (v01 PTL WHEAPTL 06040000 PTL 00000001)
ACPI: HEST 00000000c7ef3a15 000A8 (v01 PTL WHEAPTL 06040000 PTL 00000001)
ACPI: BERT 00000000c7ef3abd 00030 (v01 PTL WHEAPTL 06040000 PTL 00000001)
ACPI: SSDT 00000000c7ef3aed 000E1 (v01 wheaos wheaosc 06040000 INTL 20050624)
ACPI: ERST 00000000c7ef3bce 00270 (v01 PTL WHEAPTL 06040000 PTL 00000001)
ACPI: SRAT 00000000c7ef3e3e 000C8 (v01 AMD FAM_F_10 06040000 AMD 00000001)
ACPI: MCFG 00000000c7ef3f06 0003C (v01 PTLTD MCFG 06040000 LTP 00000000)
ACPI: HPET 00000000c7ef3f42 00038 (v01 PTLTD HPETTBL 06040000 LTP 00000001)
ACPI: APIC 00000000c7ef3f7a 0005E (v01 PTLTD ? APIC 06040000 LTP 00000000)
ACPI: BOOT 00000000c7ef3fd8 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
ACPI: Local APIC address 0xfee00000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: Node 0 PXM 0 0-a0000
SRAT: Node 0 PXM 0 100000-c8000000
SRAT: Node 0 PXM 0 100000000-238000000
NUMA: Allocated memnodemap from 11000 - 15740
NUMA: Using 20 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000238000000
NODE_DATA [0000000000015740 - 000000000004973f]
bootmap [000000000004a000 - 0000000000090fff] pages 47
(9 early reservations) ==> bootmem [0000000000 - 0238000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0001000000 - 0001ca0ff8] TEXT DATA BSS ==> [0001000000 - 0001ca0ff8]
#3 [003739e000 - 0037fef3a4] RAMDISK ==> [003739e000 - 0037fef3a4]
#4 [000009dc00 - 0000100000] BIOS reserved ==> [000009dc00 - 0000100000]
#5 [0001ca1000 - 0001ca10f8] BRK ==> [0001ca1000 - 0001ca10f8]
#6 [0000008000 - 000000c000] PGTABLE ==> [0000008000 - 000000c000]
#7 [000000c000 - 0000011000] PGTABLE ==> [000000c000 - 0000011000]
#8 [0000011000 - 0000015740] MEMNODEMAP ==> [0000011000 - 0000015740]
found SMP MP-table at [ffff8800000f7a70] f7a70
[ffffea0000000000-ffffea0007dfffff] PMD -> [ffff880028600000-ffff88002f7fffff] on node 0
Zone PFN ranges:
DMA 0x00000001 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00238000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x00000001 -> 0x0000009d
0: 0x00000100 -> 0x0007fff0
0: 0x00080000 -> 0x000c7ee0
0: 0x00100000 -> 0x00238000
On node 0 totalpages: 2096748
DMA zone: 56 pages used for memmap
DMA zone: 114 pages reserved
DMA zone: 3826 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 800520 pages, LIFO batch:31
Normal zone: 17472 pages used for memmap
Normal zone: 1260480 pages, LIFO batch:31
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000ca000
PM: Registered nosave memory: 00000000000ca000 - 0000000000100000
PM: Registered nosave memory: 000000007fff0000 - 0000000080000000
PM: Registered nosave memory: 00000000c7ee0000 - 00000000c7ef4000
PM: Registered nosave memory: 00000000c7ef4000 - 00000000c7f7f000
PM: Registered nosave memory: 00000000c7f7f000 - 00000000c7f80000
PM: Registered nosave memory: 00000000c7f80000 - 00000000c8000000
PM: Registered nosave memory: 00000000c8000000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000fff80000
PM: Registered nosave memory: 00000000fff80000 - 0000000100000000
Allocating PCI resources starting at c8000000 (gap: c8000000:18000000)
Booting paravirtualized kernel on bare hardware
NR_CPUS:4096 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 31 pages/cpu @ffff880028200000 s95064 r8192 d23720 u1048576
pcpu-alloc: s95064 r8192 d23720 u1048576 alloc=1*2097152
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2064826
Policy zone: Normal
Kernel command line: ro root=/dev/mapper/vg00-lv00 rd_MD_UUID=173392af:8b21bd50:1ee82f77:7d779ed3 rd_LVM_LV=vg00/lv00 rd_LVM_LV=vg00/lv01 rd_NO_LUKS rd_NO_DM
PID hash table entries: 4096 (order: 3, 32768 bytes)
Checking aperture...
No AGP bridge found
Node 0: aperture @ 3f4000000 size 32 MB
Aperture beyond 4GB. Ignoring.
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 20000000
PM: Registered nosave memory: 0000000020000000 - 0000000024000000
AMD-Vi disabled by default: pass amd_iommu=on to enable
Memory: 8178268k/9306112k available (4939k kernel code, 919120k absent, 208724k reserved, 3931k data, 1220k init)
Hierarchical RCU implementation.
NR_IRQS:33024 nr_irqs:424
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
allocated 83886080 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Fast TSC calibration using PIT
Detected 2310.497 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4620.99 BogoMIPS (lpj=2310497)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
tseg: 00c7f80000
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 5 MCE banks
using C1E aware idle routine
Performance Events: AMD PMU driver.
... version: 0
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 00007fffffffffff
... fixed-purpose events: 0
... event mask: 000000000000000f
ACPI: Core revision 20090903
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 20293 entries in 80 pages
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) Dual Core Processor 4450B stepping 02
Booting Node 0, Processors #1 Ok.
Brought up 2 CPUs
Total of 2 processors activated (9242.05 BogoMIPS).
Testing NMI watchdog ... OK.
sizeof(vma)=200 bytes
sizeof(page)=56 bytes
sizeof(inode)=592 bytes
sizeof(dentry)=192 bytes
sizeof(ext3inode)=800 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=232 bytes
sizeof(task_struct)=2600 bytes
devtmpfs: initialized
regulator: core version 0.5
NET: Registered protocol family 16
node 0 link 0: io port [1000, 3fff]
node 0 link 0: io port [4000, fffff]
TOM: 00000000c8000000 aka 3200M
node 0 link 0: mmio [c8000000, d21fffff]
node 0 link 0: mmio [fed00000, fed0ffff]
node 0 link 0: mmio [d8000000, dfffffff]
node 0 link 0: mmio [fec00000, fec0ffff]
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [f0000000, fe0bffff]
TOM2: 0000000238000000 aka 9088M
bus: [00,ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [c8000000, d7ffffff]
bus: 00 index 2 mmio: [fec10000, ffffffff]
bus: 00 index 3 mmio: [d8000000, febfffff]
bus: 00 index 4 mmio: [fec00000, fec0ffff]
bus: 00 index 5 mmio: [a0000, bffff]
bus: 00 index 6 mmio: [238000000, fcffffffff]
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 9
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - e09fffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
\_SB_:_OSC evaluation returned wrong type
_OSC request data:1 7
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: reg 10 io port: [0x8c00-0x8fff]
pci 0000:00:01.1: reg 10 io port: [0x2080-0x209f]
pci 0000:00:01.1: reg 20 io port: [0x2040-0x207f]
pci 0000:00:01.1: reg 24 io port: [0x2000-0x203f]
pci 0000:00:01.1: PME# supported from D3hot D3cold
pci 0000:00:01.1: PME# disabled
pci 0000:00:02.0: reg 10 32bit mmio: [0xc8000000-0xc8000fff]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: reg 10 32bit mmio: [0xc8001000-0xc80010ff]
pci 0000:00:02.1: supports D1 D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
pci 0000:00:07.0: reg 10 io port: [0x20f0-0x20f7]
pci 0000:00:07.0: reg 14 io port: [0x20e0-0x20e3]
pci 0000:00:07.0: reg 18 io port: [0x20d0-0x20d7]
pci 0000:00:07.0: reg 1c io port: [0x20c0-0x20c3]
pci 0000:00:07.0: reg 20 io port: [0x20b0-0x20bf]
pci 0000:00:07.0: reg 24 32bit mmio: [0xc8002000-0xc8002fff]
pci 0000:00:08.0: reg 10 io port: [0x2440-0x2447]
pci 0000:00:08.0: reg 14 io port: [0x2430-0x2433]
pci 0000:00:08.0: reg 18 io port: [0x2420-0x2427]
pci 0000:00:08.0: reg 1c io port: [0x2410-0x2413]
pci 0000:00:08.0: reg 20 io port: [0x2400-0x240f]
pci 0000:00:08.0: reg 24 32bit mmio: [0xc8003000-0xc8003fff]
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0c.0: PME# disabled
pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0d.0: PME# disabled
pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0e.0: PME# disabled
pci 0000:01:07.0: reg 10 32bit mmio: [0xc8110000-0xc811007f]
pci 0000:01:07.0: reg 14 io port: [0x3400-0x347f]
pci 0000:01:07.0: reg 18 io port: [0x3480-0x3487]
pci 0000:01:07.0: PME# supported from D0 D3hot
pci 0000:01:07.0: PME# disabled
pci 0000:01:08.0: reg 10 32bit mmio pref: [0xd8000000-0xdfffffff]
pci 0000:01:08.0: reg 14 io port: [0x3000-0x30ff]
pci 0000:01:08.0: reg 18 32bit mmio: [0xc8100000-0xc810ffff]
pci 0000:01:08.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
pci 0000:01:08.0: supports D1 D2
pci 0000:00:09.0: bridge io port: [0x3000-0x3fff]
pci 0000:00:09.0: bridge 32bit mmio: [0xc8100000-0xc81fffff]
pci 0000:00:09.0: bridge 32bit mmio pref: [0xd8000000-0xdfffffff]
pci 0000:02:00.0: reg 10 64bit mmio: [0xc8200000-0xc820ffff]
pci 0000:02:00.0: PME# supported from D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:0b.0: bridge 32bit mmio: [0xc8200000-0xc82fffff]
pci 0000:04:00.0: reg 10 32bit mmio: [0xc8300000-0xc831ffff]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:04:00.1: reg 10 32bit mmio: [0xc8320000-0xc833ffff]
pci 0000:00:0d.0: bridge 32bit mmio: [0xc8300000-0xc87fffff]
pci 0000:05:01.0: PME# supported from D0 D3hot D3cold
pci 0000:05:01.0: PME# disabled
pci 0000:05:05.0: PME# supported from D0 D3hot D3cold
pci 0000:05:05.0: PME# disabled
pci 0000:05:07.0: PME# supported from D0 D3hot D3cold
pci 0000:05:07.0: PME# disabled
pci 0000:05:09.0: PME# supported from D0 D3hot D3cold
pci 0000:05:09.0: PME# disabled
pci 0000:04:00.0: bridge 32bit mmio: [0xc8400000-0xc87fffff]
pci 0000:06:00.0: reg 10 64bit mmio: [0xc8400000-0xc8407fff]
pci 0000:06:00.0: PME# supported from D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:05:01.0: bridge 32bit mmio: [0xc8400000-0xc84fffff]
pci 0000:07:00.0: reg 10 64bit mmio: [0xc8500000-0xc8507fff]
pci 0000:07:00.0: PME# supported from D3hot D3cold
pci 0000:07:00.0: PME# disabled
pci 0000:05:05.0: bridge 32bit mmio: [0xc8500000-0xc85fffff]
pci 0000:08:00.0: reg 10 64bit mmio: [0xc8600000-0xc8607fff]
pci 0000:08:00.0: PME# supported from D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:05:07.0: bridge 32bit mmio: [0xc8600000-0xc86fffff]
pci 0000:09:00.0: reg 10 64bit mmio: [0xc8700000-0xc8707fff]
pci 0000:09:00.0: PME# supported from D3hot D3cold
pci 0000:09:00.0: PME# disabled
pci 0000:05:09.0: bridge 32bit mmio: [0xc8700000-0xc87fffff]
pci 0000:0a:00.0: reg 10 64bit mmio: [0xc8800000-0xc89fffff]
pci 0000:0a:00.0: reg 20 64bit mmio: [0xca000000-0xcbffffff]
pci 0000:0a:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
pci 0000:0a:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.0: PME# disabled
pci 0000:0a:00.1: reg 10 64bit mmio: [0xc8a00000-0xc8bfffff]
pci 0000:0a:00.1: reg 20 64bit mmio: [0xcc000000-0xcdffffff]
pci 0000:0a:00.1: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.1: PME# disabled
pci 0000:0a:00.2: reg 10 64bit mmio: [0xc8c00000-0xc8dfffff]
pci 0000:0a:00.2: reg 20 64bit mmio: [0xce000000-0xcfffffff]
pci 0000:0a:00.2: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.2: PME# disabled
pci 0000:0a:00.3: reg 10 64bit mmio: [0xc8e00000-0xc8ffffff]
pci 0000:0a:00.3: reg 20 64bit mmio: [0xd0000000-0xd1ffffff]
pci 0000:0a:00.3: PME# supported from D0 D3hot D3cold
pci 0000:0a:00.3: PME# disabled
pci 0000:00:0e.0: bridge 32bit mmio: [0xc8800000-0xd1ffffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
Unable to assume PCIe control: Disabling ASPM
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
vgaarb: device added: PCI:0000:01:08.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved
system 00:02: iomem range 0xe0000000-0xefffffff has been reserved
system 00:03: ioport range 0x8000-0x807f has been reserved
system 00:03: ioport range 0x8080-0x80ff has been reserved
system 00:03: ioport range 0x8400-0x847f has been reserved
system 00:03: ioport range 0x8480-0x84ff has been reserved
system 00:03: ioport range 0x8800-0x887f has been reserved
system 00:03: ioport range 0x8880-0x88ff has been reserved
system 00:03: ioport range 0x2040-0x207f has been reserved
system 00:03: ioport range 0x2000-0x203f has been reserved
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0xc00-0xc7f has been reserved
pci 0000:00:09.0: PCI bridge to [bus 01-01]
pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
pci 0000:00:09.0: bridge window [0x3000-0x3fff]
pci 0000:00:09.0: bridge window [0xc8100000-0xc81fffff]
pci 0000:00:09.0: bridge window [0xd8000000-0xdfffffff]
pci 0000:00:0b.0: PCI bridge to [bus 02-02]
pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
pci 0000:00:0b.0: bridge window [io disabled]
pci 0000:00:0b.0: bridge window [0xc8200000-0xc82fffff]
pci 0000:00:0b.0: bridge window [mem pref disabled]
pci 0000:00:0c.0: PCI bridge to [bus 03-03]
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03
pci 0000:00:0c.0: bridge window [io disabled]
pci 0000:00:0c.0: bridge window [mem disabled]
pci 0000:00:0c.0: bridge window [mem pref disabled]
pci 0000:05:01.0: PCI bridge to [bus 06-06]
pci 0000:05:01.0: PCI bridge, secondary bus 0000:06
pci 0000:05:01.0: bridge window [io disabled]
pci 0000:05:01.0: bridge window [0xc8400000-0xc84fffff]
pci 0000:05:01.0: bridge window [mem pref disabled]
pci 0000:05:05.0: PCI bridge to [bus 07-07]
pci 0000:05:05.0: PCI bridge, secondary bus 0000:07
pci 0000:05:05.0: bridge window [io disabled]
pci 0000:05:05.0: bridge window [0xc8500000-0xc85fffff]
pci 0000:05:05.0: bridge window [mem pref disabled]
pci 0000:05:07.0: PCI bridge to [bus 08-08]
pci 0000:05:07.0: PCI bridge, secondary bus 0000:08
pci 0000:05:07.0: bridge window [io disabled]
pci 0000:05:07.0: bridge window [0xc8600000-0xc86fffff]
pci 0000:05:07.0: bridge window [mem pref disabled]
pci 0000:05:09.0: PCI bridge to [bus 09-09]
pci 0000:05:09.0: PCI bridge, secondary bus 0000:09
pci 0000:05:09.0: bridge window [io disabled]
pci 0000:05:09.0: bridge window [0xc8700000-0xc87fffff]
pci 0000:05:09.0: bridge window [mem pref disabled]
pci 0000:04:00.0: PCI bridge to [bus 05-09]
pci 0000:04:00.0: PCI bridge, secondary bus 0000:05
pci 0000:04:00.0: bridge window [io disabled]
pci 0000:04:00.0: bridge window [0xc8400000-0xc87fffff]
pci 0000:04:00.0: bridge window [mem pref disabled]
pci 0000:00:0d.0: PCI bridge to [bus 04-09]
pci 0000:00:0d.0: PCI bridge, secondary bus 0000:04
pci 0000:00:0d.0: bridge window [io disabled]
pci 0000:00:0d.0: bridge window [0xc8300000-0xc87fffff]
pci 0000:00:0d.0: bridge window [mem pref disabled]
pci 0000:00:0e.0: PCI bridge to [bus 0a-0a]
pci 0000:00:0e.0: PCI bridge, secondary bus 0000:0a
pci 0000:00:0e.0: bridge window [io disabled]
pci 0000:00:0e.0: bridge window [0xc8800000-0xd1ffffff]
pci 0000:00:0e.0: bridge window [0xd2000000-0xd20fffff]
pci 0000:00:09.0: setting latency timer to 64
pci 0000:00:0b.0: setting latency timer to 64
pci 0000:00:0c.0: setting latency timer to 64
pci 0000:00:0d.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 19
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
pci 0000:04:00.0: PCI INT A -> Link[LNK4] -> GSI 19 (level, low) -> IRQ 19
pci 0000:04:00.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 18
alloc irq_desc for 18 on node 0
alloc kstat_irqs on node 0
pci 0000:05:01.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
pci 0000:05:01.0: setting latency timer to 64
pci 0000:05:05.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
pci 0000:05:05.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 17
alloc irq_desc for 17 on node 0
alloc kstat_irqs on node 0
pci 0000:05:07.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
pci 0000:05:07.0: setting latency timer to 64
pci 0000:05:09.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
pci 0000:05:09.0: setting latency timer to 64
pci 0000:00:0e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0x3000-0x3fff]
pci_bus 0000:01: resource 1 mem: [0xc8100000-0xc81fffff]
pci_bus 0000:01: resource 2 pref mem [0xd8000000-0xdfffffff]
pci_bus 0000:02: resource 1 mem: [0xc8200000-0xc82fffff]
pci_bus 0000:04: resource 1 mem: [0xc8300000-0xc87fffff]
pci_bus 0000:05: resource 1 mem: [0xc8400000-0xc87fffff]
pci_bus 0000:06: resource 1 mem: [0xc8400000-0xc84fffff]
pci_bus 0000:07: resource 1 mem: [0xc8500000-0xc85fffff]
pci_bus 0000:08: resource 1 mem: [0xc8600000-0xc86fffff]
pci_bus 0000:09: resource 1 mem: [0xc8700000-0xc87fffff]
pci_bus 0000:0a: resource 1 mem: [0xc8800000-0xd1ffffff]
pci_bus 0000:0a: resource 2 pref mem [0xd2000000-0xd20fffff]
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0b.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0b.0: Linking AER extended capability
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0c.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0c.0: Linking AER extended capability
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0d.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0d.0: Linking AER extended capability
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0e.0: Found disabled HT MSI Mapping
pci 0000:00:00.0: Found enabled HT MSI Mapping
pci 0000:00:0e.0: Linking AER extended capability
pci 0000:01:08.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 12612k freed
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 20000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
Simple Boot Flag at 0x62 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1321216138.541:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 15997
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
ksign: Installing public key data
Loading keyring
- Added public key 965331713A640F69
- User ID: CentOS (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
alloc irq_desc for 24 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:0b.0: irq 24 for MSI/MSI-X
pcieport 0000:00:0b.0: setting latency timer to 64
alloc irq_desc for 25 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:0c.0: irq 25 for MSI/MSI-X
pcieport 0000:00:0c.0: setting latency timer to 64
alloc irq_desc for 26 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:0d.0: irq 26 for MSI/MSI-X
pcieport 0000:00:0d.0: setting latency timer to 64
alloc irq_desc for 27 on node 0
alloc kstat_irqs on node 0
pcieport 0000:00:0e.0: irq 27 for MSI/MSI-X
pcieport 0000:00:0e.0: setting latency timer to 64
alloc irq_desc for 28 on node 0
alloc kstat_irqs on node 0
pcieport 0000:04:00.0: irq 28 for MSI/MSI-X
pcieport 0000:04:00.0: setting latency timer to 64
alloc irq_desc for 29 on node 0
alloc kstat_irqs on node 0
pcieport 0000:05:01.0: irq 29 for MSI/MSI-X
pcieport 0000:05:01.0: setting latency timer to 64
alloc irq_desc for 30 on node 0
alloc kstat_irqs on node 0
pcieport 0000:05:05.0: irq 30 for MSI/MSI-X
pcieport 0000:05:05.0: setting latency timer to 64
alloc irq_desc for 31 on node 0
alloc kstat_irqs on node 0
pcieport 0000:05:07.0: irq 31 for MSI/MSI-X
pcieport 0000:05:07.0: setting latency timer to 64
alloc irq_desc for 32 on node 0
alloc kstat_irqs on node 0
pcieport 0000:05:09.0: irq 32 for MSI/MSI-X
pcieport 0000:05:09.0: setting latency timer to 64
aer 0000:00:0b.0:pcie02: AER service couldn't init device: no _OSC support
aer 0000:00:0c.0:pcie02: AER service couldn't init device: no _OSC support
aer 0000:00:0d.0:pcie02: AER service couldn't init device: no _OSC support
aer 0000:00:0e.0:pcie02: AER service couldn't init device: no _OSC support
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
pci-stub: invalid id string ""
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
crash memory driver: version 1.0
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 0000:01:07.0: PCI INT A -> Link[LNK4] -> GSI 19 (level, low) -> IRQ 19
serial 0000:01:07.0: PCI INT A disabled
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 23
alloc irq_desc for 23 on node 0
alloc kstat_irqs on node 0
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 23, io mem 0xc8001000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32-71.29.1.el6.x86_64 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
alloc irq_desc for 22 on node 0
alloc kstat_irqs on node 0
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 22, io mem 0xc8000000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32-71.29.1.el6.x86_64 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:08: RTC can wake from S4
rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
registered taskstats version 1
rtc_cmos 00:08: setting system clock to 2011-11-13 20:28:59 UTC (1321216139)
Initalizing network drop monitor service
Freeing unused kernel memory: 1220k freed
Write protecting the kernel read-only data: 7184k
dracut: dracut-004-33.2.el6_0
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@xxxxxxxxxx
udev: starting version 147
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
radeon 0000:01:08.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
[drm] initializing kernel modesetting (RV100 0x1002:0x515E).
[drm] register mmio base: 0xC8100000
[drm] register mmio size: 65536
radeon 0000:01:08.0: VRAM: 64M 0xD8000000 - 0xDBFFFFFF (32M used)
radeon 0000:01:08.0: GTT: 512M 0xB8000000 - 0xD7FFFFFF
[drm] radeon: irq initialized.
[drm] Detected VRAM RAM=64M, BAR=128M
[drm] RAM width 16bits DDR
[TTM] Zone kernel: Available graphics memory: 4096052 kiB.
[TTM] Zone dma32: Available graphics memory: 2097152 kiB.
[drm] radeon: 32M of VRAM memory ready
[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 131072, num gpu pages 131072
[drm] Loading R100 Microcode
platform radeon_cp.0: firmware: requesting radeon/R100_cp.bin
[drm] radeon: ring at 0x00000000B8000000
[drm] ring test succeeded in 1 usecs
[drm] radeon: ib pool ready.
[drm] ib test succeeded in 0 usecs
[drm] Radeon Display Connectors
[drm] Connector 0:
[drm] VGA
[drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[drm] Encoders:
[drm] CRT1: INTERNAL_DAC1
[drm] fb mappable at 0xD8040000
[drm] vram apper at 0xD8000000
[drm] size 786432
[drm] fb depth is 8
[drm] pitch is 1024
fbcon: radeondrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
fb0: radeondrmfb frame buffer device
drm: registered panic notifier
Slow work thread pool: Starting up
Slow work thread pool: Ready
[drm] Initialized radeon 2.1.0 20080528 for 0000:01:08.0 on minor 0
dracut: Starting plymouth daemon
usb 2-2: new full speed USB device using ohci_hcd and address 2
sata_nv 0000:00:07.0: version 3.5
sata_nv 0000:00:07.0: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
alloc irq_desc for 21 on node 0
alloc kstat_irqs on node 0
sata_nv 0000:00:07.0: PCI INT A -> Link[LTID] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:07.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x20f0 ctl 0x20e0 bmdma 0x20b0 irq 21
ata2: SATA max UDMA/133 cmd 0x20d0 ctl 0x20c0 bmdma 0x20b8 irq 21
sata_nv 0000:00:08.0: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 20
alloc irq_desc for 20 on node 0
alloc kstat_irqs on node 0
sata_nv 0000:00:08.0: PCI INT A -> Link[LSI1] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:08.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x2440 ctl 0x2430 bmdma 0x2400 irq 20
ata4: SATA max UDMA/133 cmd 0x2420 ctl 0x2410 bmdma 0x2408 irq 20
usb 2-2: New USB device found, idVendor=0557, idProduct=2804
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: USB HID Composite Device
usb 2-2: Manufacturer: ATEN
usb 2-2: configuration #1 chosen from 1 choice
input: ATEN USB HID Composite Device as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input3
generic-usb 0003:0557:2804.0001: input,hidraw0: USB HID v1.00 Keyboard [ATEN USB HID Composite Device] on usb-0000:00:02.0-2/input0
input: ATEN USB HID Composite Device as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.1/input/input4
generic-usb 0003:0557:2804.0002: input,hidraw1: USB HID v1.00 Mouse [ATEN USB HID Composite Device] on usb-0000:00:02.0-2/input1
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: WDC WD1602ABKS-18N8A0, 02.03B04, max UDMA/133
ata1.00: 312500000 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD1602ABKS-1 02.0 PQ: 0 ANSI: 5
ata3.00: ATA-8: ST3250310NS, SN06, max UDMA/133
ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-8: WDC WD1602ABKS-18N8A0, 02.03B04, max UDMA/133
ata2.00: 312500000 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA WDC WD1602ABKS-1 02.0 PQ: 0 ANSI: 5
scsi 2:0:0:0: Direct-Access ATA ST3250310NS SN06 PQ: 0 ANSI: 5
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: HL-DT-ST BD-RE WH12LS38, 1.00, max UDMA/133
ata4.00: configured for UDMA/133
scsi 3:0:0:0: CD-ROM HL-DT-ST BD-RE WH12LS38 1.00 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312500000 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sdb] 312500000 512-byte logical blocks: (160 GB/149 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb:
sd 2:0:0:0: [sdc] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sdb1 sdb2
sdc1
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] Attached SCSI disk
sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
dracut: Autoassembling MD Raid
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
md: raid1 personality registered for level 1
raid1: raid set md0 active with 2 out of 2 mirrors
md0: detected capacity change from 0 to 104845312
dracut: mdadm: /dev/md0 has been started with 2 drives.
md0: detected capacity change from 0 to 104845312
md0:
md: md1 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
md1: bitmap initialized from disk: read 1/1 pages, set 0 bits
created bitmap (2 pages) for device md1
md1: detected capacity change from 0 to 159892041728
dracut: mdadm: /dev/md1 has been started with 2 drives.
md1: detected capacity change from 0 to 159892041728
md1: unknown partition table
dracut: Scanning devices md1 for LVM logical volumes vg00/lv00 vg00/lv01
dracut: inactive '/dev/vg00/lv02' [20.00 GiB] inherit
dracut: inactive '/dev/vg00/lv00' [7.50 GiB] inherit
dracut: inactive '/dev/vg00/lv01' [2.00 GiB] inherit
dracut: inactive '/dev/vg00/lv99' [119.38 GiB] contiguous
EXT4-fs (dm-0): mounted filesystem with ordered data mode
dracut: Mounted root filesystem /dev/mapper/vg00-lv00
dracut: Loading SELinux policy
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
type=1404 audit(1321216143.013:2): selinux=0 auid=4294967295 ses=4294967295
dracut: /sbin/load_policy: Can't load policy: No such file or directory
dracut: Switching root
udev: starting version 147
i2c i2c-1: nForce2 SMBus adapter at 0x2040
i2c i2c-2: nForce2 SMBus adapter at 0x2000
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sr 3:0:0:0: Attached scsi generic sg3 type 5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
tg3.c:v3.108 (February 17, 2010)
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 16
alloc irq_desc for 16 on node 0
alloc kstat_irqs on node 0
tg3 0000:02:00.0: PCI INT A -> Link[LNK2] -> GSI 16 (level, low) -> IRQ 16
tg3 0000:02:00.0: setting latency timer to 64
eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 00:26:b9:7f:6d:04
eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
QLogic/NetXen Network Driver v4.0.72
netxen_nic 0000:0a:00.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
netxen_nic 0000:0a:00.0: setting latency timer to 64
netxen_nic 0000:0a:00.0: 2MB memory map
netxen_nic 0000:0a:00.0: firmware: requesting phanfw.bin
netxen_nic 0000:0a:00.0: firmware: requesting nx3fwct.bin
netxen_nic 0000:0a:00.0: loading firmware from flash
netxen_nic: Quad Gig LP Board S/N QG8CBK0078 Chip rev 0x42
netxen_nic 0000:0a:00.0: firmware v4.0.228 [cut-through]
alloc irq_desc for 33 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.0: irq 33 for MSI/MSI-X
alloc irq_desc for 34 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.0: irq 34 for MSI/MSI-X
netxen_nic 0000:0a:00.0: using msi-x interrupts
netxen_nic 0000:0a:00.0: eth1: GbE port initialized
netxen_nic 0000:0a:00.1: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
netxen_nic 0000:0a:00.1: setting latency timer to 64
netxen_nic 0000:0a:00.1: 2MB memory map
netxen_nic 0000:0a:00.1: firmware v4.0.228 [cut-through]
alloc irq_desc for 35 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.1: irq 35 for MSI/MSI-X
alloc irq_desc for 36 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.1: irq 36 for MSI/MSI-X
netxen_nic 0000:0a:00.1: using msi-x interrupts
netxen_nic 0000:0a:00.1: eth2: GbE port initialized
netxen_nic 0000:0a:00.2: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
netxen_nic 0000:0a:00.2: setting latency timer to 64
netxen_nic 0000:0a:00.2: 2MB memory map
netxen_nic 0000:0a:00.2: firmware v4.0.228 [cut-through]
alloc irq_desc for 37 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.2: irq 37 for MSI/MSI-X
alloc irq_desc for 38 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.2: irq 38 for MSI/MSI-X
netxen_nic 0000:0a:00.2: using msi-x interrupts
netxen_nic 0000:0a:00.2: eth3: GbE port initialized
netxen_nic 0000:0a:00.3: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
netxen_nic 0000:0a:00.3: setting latency timer to 64
netxen_nic 0000:0a:00.3: 2MB memory map
netxen_nic 0000:0a:00.3: firmware v4.0.228 [cut-through]
alloc irq_desc for 39 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.3: irq 39 for MSI/MSI-X
alloc irq_desc for 40 on node 0
alloc kstat_irqs on node 0
netxen_nic 0000:0a:00.3: irq 40 for MSI/MSI-X
netxen_nic 0000:0a:00.3: using msi-x interrupts
netxen_nic 0000:0a:00.3: eth4: GbE port initialized
k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
EDAC MC: Ver: 2.1.0 Jun 27 2011
EDAC amd64_edac: Ver: 3.3.0 Jun 27 2011
EDAC amd64: ECC is enabled by BIOS.
EDAC MC: Rev F or later detected
EDAC MC: DCT0 chip selects:
EDAC MC: 0: 4096MB 1: 0MB
EDAC MC: 2: 2048MB 3: 2048MB
EDAC MC: 4: 0MB 5: 0MB
EDAC MC: 6: 0MB 7: 0MB
EDAC MC0: Giving out device to 'amd64_edac' 'RevF': DEV 0000:00:18.2
EDAC PCI0: Giving out device to module 'amd64_edac' controller 'EDAC PCI controller': DEV '0000:00:18.2' (POLLED)
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
EXT4-fs (md0): mounted filesystem with ordered data mode
EXT4-fs (dm-2): mounted filesystem with ordered data mode
Adding 2097144k swap on /dev/mapper/vg00-lv01. Priority:-1 extents:1 across:2097144k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
netxen_nic: eth1 NIC Link is up
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
ADDRCONF(NETDEV_UP): eth2: link is not ready
netxen_nic: eth2 NIC Link is up
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
xhci_hcd 0000:06:00.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
xhci_hcd 0000:06:00.0: setting latency timer to 64
xhci_hcd 0000:06:00.0: xHCI Host Controller
xhci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:06:00.0: irq 18, io mem 0xc8400000
usb usb3: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
usb usb3: SerialNumber: 0000:06:00.0
usb usb3: configuration #1 chosen from 1 choice
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
xhci_hcd 0000:07:00.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
xhci_hcd 0000:07:00.0: setting latency timer to 64
xhci_hcd 0000:07:00.0: xHCI Host Controller
xhci_hcd 0000:07:00.0: new USB bus registered, assigned bus number 4
xhci_hcd 0000:07:00.0: irq 18, io mem 0xc8500000
usb usb4: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
usb usb4: SerialNumber: 0000:07:00.0
usb usb4: configuration #1 chosen from 1 choice
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
xhci_hcd 0000:08:00.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
xhci_hcd 0000:08:00.0: setting latency timer to 64
xhci_hcd 0000:08:00.0: xHCI Host Controller
xhci_hcd 0000:08:00.0: new USB bus registered, assigned bus number 5
xhci_hcd 0000:08:00.0: irq 17, io mem 0xc8600000
usb usb5: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: xHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
usb usb5: SerialNumber: 0000:08:00.0
usb usb5: configuration #1 chosen from 1 choice
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 4 ports detected
xhci_hcd 0000:09:00.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
xhci_hcd 0000:09:00.0: setting latency timer to 64
xhci_hcd 0000:09:00.0: xHCI Host Controller
xhci_hcd 0000:09:00.0: new USB bus registered, assigned bus number 6
xhci_hcd 0000:09:00.0: irq 18, io mem 0xc8700000
usb usb6: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: xHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
usb usb6: SerialNumber: 0000:09:00.0
usb usb6: configuration #1 chosen from 1 choice
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
usb 5-1: new SuperSpeed USB device using xhci_hcd and address 2
xhci_hcd 0000:08:00.0: WARN: short transfer on control ep
xhci_hcd 0000:08:00.0: WARN: short transfer on control ep
xhci_hcd 0000:08:00.0: WARN: short transfer on control ep
xhci_hcd 0000:08:00.0: WARN: short transfer on control ep
usb 5-1: New USB device found, idVendor=1058, idProduct=1130
usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-1: Product: My Book 1130
usb 5-1: Manufacturer: Western Digital
usb 5-1: SerialNumber: 574341575A30333233363137
usb 5-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access WD My Book 1130 1016 PQ: 0 ANSI: 6
scsi 4:0:0:1: Enclosure WD SES Device 1016 PQ: 0 ANSI: 6
sd 4:0:0:0: Attached scsi generic sg4 type 0
scsi 4:0:0:1: Attached scsi generic sg5 type 13
sd 4:0:0:0: [sdd] 732558336 4096-byte logical blocks: (3.00 TB/2.72 TiB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 47 00 10 08
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sd 4:0:0:0: [sdd] 732558336 4096-byte logical blocks: (3.00 TB/2.72 TiB)
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sdd: unknown partition table
sd 4:0:0:0: [sdd] 732558336 4096-byte logical blocks: (3.00 TB/2.72 TiB)
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sd 4:0:0:0: [sdd] Attached SCSI disk
ses 4:0:0:1: Attached Enclosure device
xhci_hcd 0000:08:00.0: WARN: Stalled endpoint
xhci_hcd 0000:08:00.0: WARN: Stalled endpoint
EXT4-fs (dm-4): mounted filesystem with ordered data mode
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: USB disconnect, address 2
sd 4:0:0:0: Device offlined - not ready after error recovery
sd 4:0:0:0: [sdd] Unhandled error code
sd 4:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 4:0:0:0: [sdd] CDB: Write(10): 2a 00 14 ed a8 8a 00 00 1e 00
end_request: I/O error, dev sdd, sector 2808955984
sd 4:0:0:0: [sdd] Unhandled error code
sd 4:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
Aborting journal on device dm-4-8.
Buffer I/O error on device dm-4, logical block 365985792
lost page write due to I/O error on dm-4
JBD2: I/O error detected when updating journal superblock for dm-4-8.
sd 4:0:0:0: [sdd] CDB: Write(10): 2a 00 14 ed a8 a8 00 00 1e 00
end_request: I/O error, dev sdd, sector 2808956224
Buffer I/O error on device dm-4, logical block 350224385
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224386
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224387
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224388
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224389
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224390
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224391
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224392
lost page write due to I/O error on dm-4
Buffer I/O error on device dm-4, logical block 350224393
lost page write due to I/O error on dm-4
EXT4-fs error (device dm-4): ext4_journal_start_sb: Detected aborted journal
EXT4-fs (dm-4): Remounting filesystem read-only
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
hub 5-0:1.0: unable to enumerate USB device on port 1
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
usb 5-1: Device not responding to set address.
usb 5-1: device not accepting address 0, error -71
hub 5-0:1.0: cannot disable port 1 (err = -32)
usb 5-1: Device not responding to set address.
filename: /lib/modules/2.6.32-71.29.1.el6.x86_64/kernel/drivers/usb/host/xhci-hcd.ko
license: GPL
author: Sarah Sharp
description: 'eXtensible' Host Controller (xHC) Driver
srcversion: 9C1A3D3617F9B782877A8C8
depends:
vermagic: 2.6.32-71.29.1.el6.x86_64 SMP mod_unload modversions
parm: link_quirk:Don't clear the chain bit on a link TRB (int)
# dmidecode 2.10
SMBIOS 2.5 present.
48 structures occupying 1808 bytes.
Table at 0x000F0BA0.
Handle 0x0000, DMI type 218, 29 bytes
OEM-specific Type
Header and Data:
DA 1D 00 00 2E 84 17 01 0C 20 00 10 F5 10 F5 00
00 11 F5 11 F5 00 00 FF FF 00 00 00 00
Handle 0x0001, DMI type 0, 24 bytes
BIOS Information
Vendor: Dell Inc.
Version: 1.4.4
Release Date: 07/30/2009
Address: 0xE3F50
Runtime Size: 114864 bytes
ROM Size: 1024 kB
Characteristics:
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
EDD is supported
5.25"/360 kB floppy services are supported (int 13h)
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
Targeted content distribution is supported
BIOS Revision: 1.4
Handle 0x0002, DMI type 1, 27 bytes
System Information
Manufacturer: Dell Inc.
Product Name: PowerEdge T105
Version: (none)
Serial Number: GV9NBM1
UUID: 44454C4C-5600-1039-804E-C7C04F424D31
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0003, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Dell Inc.
Product Name: 0Y9FTT
Version: A00
Serial Number: ..CN708219C9L02X.
Handle 0x0004, DMI type 3, 13 bytes
Chassis Information
Manufacturer: Dell Inc.
Type: Tower
Lock: Not Present
Version: Not Specified
Serial Number: GV9NBM1
Asset Tag:
Boot-up State: Warning
Power Supply State: Safe
Thermal State: Safe
Security Status: None
Handle 0x0005, DMI type 4, 40 bytes
Processor Information
Socket Designation: Socket A
Type: Central Processor
Family: Athlon 64 X2
Manufacturer: AMD
ID: B2 0F 06 00 FF FB 8B 17
Signature: Family 15, Model 107, Stepping 2
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
HTT (Hyper-threading technology)
Version: G2
Voltage: 1.4 V
External Clock: 1000 MHz
Max Speed: 2300 MHz
Current Speed: 2300 MHz
Status: Populated, Enabled
Upgrade: Socket AM2
L1 Cache Handle: 0x0006
L2 Cache Handle: 0x0007
L3 Cache Handle: 0x0008
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Core Count: 2
Core Enabled: 2
Thread Count: 2
Characteristics:
64-bit capable
Handle 0x0006, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1 Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 256 kB
Maximum Size: 256 kB
Supported SRAM Types:
Pipeline Burst
Installed SRAM Type: Pipeline Burst
Speed: 1 ns
Error Correction Type: Multi-bit ECC
System Type: Unified
Associativity: 2-way Set-associative
Handle 0x0007, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2 Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 1024 kB
Maximum Size: 1024 kB
Supported SRAM Types:
Pipeline Burst
Installed SRAM Type: Pipeline Burst
Speed: 1 ns
Error Correction Type: Multi-bit ECC
System Type: Unified
Associativity: 16-way Set-associative
Handle 0x0008, DMI type 7, 19 bytes
Cache Information
Socket Designation: L3 Cache
Configuration: Enabled, Not Socketed, Level 3
Operational Mode: Write Back
Location: Internal
Installed Size: 0 kB
Maximum Size: 0 kB
Supported SRAM Types:
Pipeline Burst
Installed SRAM Type: Pipeline Burst
Speed: 1 ns
Error Correction Type: Multi-bit ECC
System Type: Unified
Associativity: Other
Handle 0x0009, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: DB-15 female
Port Type: Video Port
Handle 0x000A, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x000B, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x000C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x000D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x000E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x000F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0010, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0011, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: Access Bus (USB)
External Reference Designator: none
External Connector Type: None
Port Type: USB
Handle 0x0012, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: RJ-45
Port Type: Network Port
Handle 0x0013, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: none
Internal Connector Type: None
External Reference Designator: none
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x0014, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT1
Type: x8 PCI Express
Current Usage: In Use
Length: Long
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Handle 0x0015, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT2
Type: x8 PCI Express
Current Usage: Available
Length: Long
ID: 0
Characteristics:
3.3 V is provided
PME signal is supported
Handle 0x0016, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT3
Type: x1 PCI Express
Current Usage: Available
Length: Long
ID: 4
Characteristics:
3.3 V is provided
PME signal is supported
Handle 0x0017, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT4
Type: 32-bit PCI
Current Usage: In Use
Length: Short
ID: 3
Characteristics:
3.3 V is provided
PME signal is supported
Handle 0x0018, DMI type 10, 8 bytes
On Board Device 1 Information
Type: Video
Status: Disabled
Description: Embedded ATI ES1000 Video
On Board Device 2 Information
Type: Ethernet
Status: Disabled
Description: Embedded Broadcom 5722 NIC 1
Handle 0x0019, DMI type 11, 5 bytes
OEM Strings
String 1: www.dell.com
Handle 0x001A, DMI type 13, 22 bytes
BIOS Language Information
Installable Languages: 1
en|US|iso8859-1
Currently Installed Language: en|US|iso8859-1
Handle 0x001B, DMI type 15, 29 bytes
System Event Log
Area Length: 40 bytes
Header Start Offset: 0x0000
Header Length: 32 bytes
Data Start Offset: 0x0020
Access Method: General-purpose non-volatile data functions
Access Address: 0x0000
Status: Valid, Not Full
Change Token: 0x00000022
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: Single-bit ECC memory error
Data Format 2: Multiple-event
Descriptor 3: Multi-bit ECC memory error
Data Format 3: Multiple-event
Handle 0x001C, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: Single-bit ECC
Maximum Capacity: 8 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x001D, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: DIMM1
Bank Locator: Bank 1
Type: DDR2
Type Detail: Synchronous
Speed: 800 MHz
Manufacturer: AD00000000000000
Serial Number: 6112522E
Asset Tag: 011012
Part Number: HYMP125U72CP8-S6
Handle 0x001E, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 2
Locator: DIMM2
Bank Locator: Bank 1
Type: DDR2
Type Detail: Synchronous
Speed: 800 MHz
Manufacturer: AD00000000000000
Serial Number: 6132522D
Asset Tag: 011012
Part Number: HYMP125U72CP8-S6
Handle 0x001F, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 3
Locator: DIMM3
Bank Locator: Bank 2
Type: DDR2
Type Detail: Synchronous
Speed: 800 MHz
Manufacturer: 2C00000000000000
Serial Number: E080F6B1
Asset Tag: 081117
Part Number: 9HTF25672AZ-80EC1
Handle 0x0020, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x001C
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 4
Locator: DIMM4
Bank Locator: Bank 2
Type: DDR2
Type Detail: Synchronous
Speed: 800 MHz
Manufacturer: 2C00000000000000
Serial Number: E080F6AA
Asset Tag: 081117
Part Number: 9HTF25672AZ-80EC1
Handle 0x0021, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x001FFFFFFFF
Range Size: 8 GB
Physical Array Handle: 0x001C
Partition Width: 0
Handle 0x0022, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x001D
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 1
Handle 0x0023, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FFFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x001E
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 1
Handle 0x0024, DMI type 27, 14 bytes
Cooling Device
Temperature Probe Handle: 0x0026
Type: Fan
Status: OK
Cooling Unit Group: 255
OEM-specific Information: 0x00000000
Nominal Speed: 861 rpm
Handle 0x0025, DMI type 27, 14 bytes
Cooling Device
Temperature Probe Handle: 0x0026
Type: Fan
Status: OK
Cooling Unit Group: 255
OEM-specific Information: 0x00000000
Nominal Speed: 0 rpm
Handle 0x0026, DMI type 28, 22 bytes
Temperature Probe
Description: Temperatur probe
Location: Processor
Status: OK
Maximum Value: 92.0 deg C
Minimum Value: 0.0 deg C
Resolution: 2.000 deg C
Tolerance: 2.0 deg C
Accuracy: 0.25%
OEM-specific Information: 0x00000000
Nominal Value: 36.0 deg C
Handle 0x0027, DMI type 32, 20 bytes
System Boot Information
Status: <OUT OF SPEC>
Handle 0x0028, DMI type 208, 10 bytes
OEM-specific Type
Header and Data:
D0 0A 28 00 00 01 FE 00 25 02
Handle 0x0029, DMI type 210, 12 bytes
OEM-specific Type
Header and Data:
D2 0C 29 00 F8 03 04 03 06 80 04 03
Handle 0x002A, DMI type 212, 137 bytes
OEM-specific Type
Header and Data:
D4 89 2A 00 70 00 71 00 00 10 2D 2E 18 C0 5C 00
04 00 90 5A 00 00 01 90 5B 00 00 03 80 63 FD 00
02 80 63 FD 02 27 40 63 EF 00 26 40 63 EF 10 DE
00 4B EF 10 43 00 1C CF 20 42 00 1C CF 10 92 00
13 F3 08 91 00 13 F3 04 90 00 13 F3 00 9E 00 26
BF 40 9D 00 26 BF 00 A3 00 13 CF 20 A2 00 13 CF
10 A1 00 13 CF 00 37 01 1B DF 00 35 01 1B DF 20
32 40 1B E7 10 31 40 1B E7 00 0F 00 11 3F 00 10
00 11 3F 80 FF FF 00 00 00
Handle 0x002B, DMI type 212, 182 bytes
OEM-specific Type
Header and Data:
D4 B6 2B 00 70 00 71 00 00 42 59 60 03 A0 4A FB
00 02 A0 4A FB 04 6C 01 52 CF 00 6B 01 52 CF 10
6A 01 52 CF 20 1E 01 52 FD 02 1D 01 52 FD 00 1C
01 52 FE 01 1B 01 52 FE 00 1A 01 4B 7F 80 19 01
4B 7F 00 18 01 4B BF 40 17 01 4B BF 00 FF 00 47
BF 40 FE 00 47 BF 00 FD 00 43 3F 00 A0 00 4B DF
00 9F 00 4B DF 20 1B 00 48 3F C0 1A 00 48 3F 80
19 00 48 3F 00 6E 00 52 F3 04 44 01 42 FE 00 45
01 42 FE 01 2E 00 52 F3 00 2D 00 52 F3 08 DA 01
52 F3 0C 01 40 52 7F 00 02 40 52 7F 80 22 40 63
DF 20 23 40 63 DF 00 83 00 38 00 00 84 00 39 00
00 FF FF 00 00 00
Handle 0x002C, DMI type 212, 27 bytes
OEM-specific Type
Header and Data:
D4 1B 2C 00 72 00 73 00 00 C4 FD FE 03 C0 8B 00
07 00 C0 80 00 0A FF FF 00 00 00
Handle 0x002D, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 2D 00 00 01 00 00 00 10 F5 00 00 00 00 00
00 00 00
Handle 0x002E, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 2E 00 00 01 00 00 00 11 F5 00 00 00 00 00
00 00 00
Handle 0x002F, DMI type 127, 4 bytes
End Of Table
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4)
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1)
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a4)
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2)
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3)
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3)
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3)
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:07.0 Serial controller: Sealevel Systems Inc Device 7106 (rev 01)
01:08.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
04:00.1 System peripheral: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
05:01.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
05:05.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
05:07.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
05:09.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
06:00.0 USB Controller: Device 1b21:1042
07:00.0 USB Controller: Device 1b21:1042
08:00.0 USB Controller: Device 1b21:1042
09:00.0 USB Controller: Device 1b21:1042
0a:00.0 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
0a:00.1 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
0a:00.2 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
0a:00.3 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4)
Subsystem: Dell PowerEdge T105 Memory Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1)
Subsystem: Dell PowerEdge T105 ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: I/O ports at 8c00 [size=1K]
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
Subsystem: Dell PowerEdge T105 SMBus
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 2080 [size=32]
Region 4: I/O ports at 2040 [size=64]
Region 5: I/O ports at 2000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: Dell PowerEdge T105 onboard USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at c8000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a4) (prog-if 20 [EHCI])
Subsystem: Dell PowerEdge T105 onboard USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at c8001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: Dell PowerEdge T105 Serial ATA
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 20f0 [size=8]
Region 1: I/O ports at 20e0 [size=4]
Region 2: I/O ports at 20d0 [size=8]
Region 3: I/O ports at 20c0 [size=4]
Region 4: I/O ports at 20b0 [size=16]
Region 5: Memory at c8002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: ata_generic, pata_acpi, sata_nv
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: Dell PowerEdge T105 Serial ATA
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 2440 [size=8]
Region 1: I/O ports at 2430 [size=4]
Region 2: I/O ports at 2420 [size=8]
Region 3: I/O ports at 2410 [size=4]
Region 4: I/O ports at 2400 [size=16]
Region 5: Memory at c8003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: ata_generic, pata_acpi, sata_nv
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c8100000-c81fffff
Prefetchable memory behind bridge: d8000000-dfffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode])
Physical Slot: 0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8200000-c82fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fee0300c Data: 4161
Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr+ UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 8, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [160] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode])
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fee0300c Data: 4169
Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 4, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [160] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 1b, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=09, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8300000-c87fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fee0300c Data: 4171
Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 2, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [160] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 0e, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Physical Slot: 2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8800000-d1ffffff
Prefetchable memory behind bridge: 00000000d2000000-00000000d20fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fee0300c Data: 4179
Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 1, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [160] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 1.02
Link Frequency: 1.0GHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: amd64_edac
Kernel modules: amd64_edac_mod
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:07.0 Serial controller: Sealevel Systems Inc Device 7106 (rev 01) (prog-if 02 [16550])
Subsystem: Sealevel Systems Inc Device 7106
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c8110000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 3400 [size=128]
Region 2: I/O ports at 3480 [size=8]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
01:08.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog-if 00 [VGA controller])
Subsystem: Dell PowerEdge T105 Embedded ATI ES1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+ DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at c8100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c8120000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: radeon
Kernel modules: radeon, radeonfb
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express
Subsystem: Dell PowerEdge T105 Broadcom NetXtreme 5722
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c8200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95722
[EC] Engineering changes: 106679-15
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 34 65 34
[RV] Reserved: checksum good, 28 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [58] Vendor Specific Information <?>
Capabilities: [e8] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 96a343a8c477f5e0 Data: fce0
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [13c] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-26-b9-ff-fe-7f-6d-04
Capabilities: [16c] Power Budgeting <?>
Kernel driver in use: tg3
Kernel modules: tg3
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at c8300000 (32-bit, non-prefetchable) [size=128K]
Bus: primary=04, secondary=05, subordinate=09, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8400000-c87fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee0300c Data: 4181
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Upstream Port, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-SlotPowerLimit 0.000000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <2us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [138] Power Budgeting <?>
Capabilities: [148] Virtual Channel <?>
Capabilities: [448] Vendor Specific Information <?>
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
04:00.1 System peripheral: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba)
Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at c8320000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/8 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [68] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend+
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <2us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [1f4] Vendor Specific Information <?>
05:01.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8400000-c84fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee0300c Data: 4189
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 1, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [148] Virtual Channel <?>
Capabilities: [520] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
05:05.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8500000-c85fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee0300c Data: 4191
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 5, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [148] Virtual Channel <?>
Capabilities: [520] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
05:07.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8600000-c86fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee0300c Data: 4199
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #7, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 7, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [148] Virtual Channel <?>
Capabilities: [520] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
05:09.0 PCI bridge: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA (rev ba) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: c8700000-c87fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee0300c Data: 41a1
Masking: 00000001 Pending: 00000000
Capabilities: [68] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #9, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <2us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive+ BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 9, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a4] Subsystem: PLX Technology, Inc. PEX 8609 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch with DMA
Capabilities: [100] Device Serial Number ba-86-01-10-b5-df-0e-00
Capabilities: [fb4] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 1f, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [148] Virtual Channel <?>
Capabilities: [520] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [950] Vendor Specific Information <?>
Kernel driver in use: pcieport
Kernel modules: shpchp
06:00.0 USB Controller: Device 1b21:1042 (prog-if 30)
Subsystem: Device 174c:2104
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8400000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [68] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00002080
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: xhci_hcd
07:00.0 USB Controller: Device 1b21:1042 (prog-if 30)
Subsystem: Device 174c:2104
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8500000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [68] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00002080
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: xhci_hcd
08:00.0 USB Controller: Device 1b21:1042 (prog-if 30)
Subsystem: Device 174c:2104
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c8600000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [68] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00002080
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: xhci_hcd
09:00.0 USB Controller: Device 1b21:1042 (prog-if 30)
Subsystem: Device 174c:2104
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8700000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [68] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00002080
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: xhci_hcd
0a:00.0 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
Subsystem: NetXen Incorporated NX3031 Quad Port Gigabit Server Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c8800000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at ca000000 (64-bit, non-prefetchable) [size=32M]
[virtual] Expansion ROM at d2000000 [disabled] [size=64K]
Capabilities: [40] MSI-X: Enable+ Count=64 Masked-
Vector table: BAR=0 offset=00080000
PBA: BAR=0 offset=00081000
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/32 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 256 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
0a:00.1 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
Subsystem: NetXen Incorporated NX3031 Quad Port Gigabit Server Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c8a00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at cc000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [40] MSI-X: Enable+ Count=64 Masked-
Vector table: BAR=0 offset=00082000
PBA: BAR=0 offset=00083000
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/32 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 256 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
0a:00.2 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
Subsystem: NetXen Incorporated NX3031 Quad Port Gigabit Server Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c8c00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at ce000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [40] MSI-X: Enable+ Count=64 Masked-
Vector table: BAR=0 offset=00084000
PBA: BAR=0 offset=00085000
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/32 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 256 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
0a:00.3 Ethernet controller: NetXen Incorporated NX3031 Multifunction 1/10-Gigabit Server Adapter (rev 42)
Subsystem: NetXen Incorporated NX3031 Quad Port Gigabit Server Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c8e00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at d0000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [40] MSI-X: Enable+ Count=64 Masked-
Vector table: BAR=0 offset=00086000
PBA: BAR=0 offset=00087000
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/32 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 256 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:09:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:08:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:07:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.32-71.29.1.el6.x86_64 xhci_hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:06:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 002 Device 002: ID 0557:2804 ATEN International Co., Ltd
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0557 ATEN International Co., Ltd
idProduct 0x2804
bcdDevice 2.00
iManufacturer 1 ATEN
iProduct 2 USB HID Composite Device
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 3 USB HID Composite Device
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 65
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 8
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 52
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 8
Device Status: 0x0001
Self Powered
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.32-71.29.1.el6.x86_64 ohci_hcd
iProduct 2 OHCI Host Controller
iSerial 1 0000:00:02.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 10
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Port 9: 0000.0100 power
Port 10: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.32-71.29.1.el6.x86_64 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:02.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 10
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Port 9: 0000.0100 power
Port 10: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
