These patches are based on:http://patchwork.ozlabs.org/patch/89560/ After not getting any reply from developers, I started to do modifications for my platform (SPEAr1340). I have done modifications in such a way that all the code in driver/usb/dwc/ would be platform independent. I have tested this code for host/device/dma/slave mode. My fifo configuration is dedicated and dynamic. Changes since v13: 1. All the patches has been renamed from usb/ppc4xx to dwc/otg. Changes has been done, because these files are valid for other architecture also. 2. Parameter passing mechanism has been modified. Now, driver can also receive parameters from a platform device. 3. Next request is started after clear halt for all slave transfer There might be a situation, when there are data into fifo, EP is receiving IN token, but EP is disabled. In this case, EP will just stop and do nothing. So, for each transfer type start_next_request is enabled. 4. Dynamic fifo was configured by reading number of endpoints. Number of endpoints can be different than the number of dynamic fifo in the controller. Number of dynamic fifo is programmed in fifo_number parameter. Program fifos only for fifo_number of fifo. 5. If platform specific functions like phy_init and param_init is defined then call it. 6. Few define which are used for TX, were defined as RX in the code. All such definition has been replaced throughout the code. 7. There are some defined steps to disable an endpoint. It can not be disabled just by setting epdisable bit. Now, it is disabled as specification says. During stall of and endpoint, first stall bit should be set and then endpoint should be disabled. In dwc_otg_pcd_ep_disable, TX fifo must be flushed along with disabling of endpoint. In DMA mode if Fifo is flushed only once then, DMA will write data into it again. So, it must be flushed till DMA transfer is complete. 8. dwc_otg_ep_deactivate is called after dwc_otg_ep_disable. 9. platform_get_irq return -ENXIO , if requested IRQ is not found. So, return must be checked accordingly. 10. There is a struct (core_params) for all possible variable parameters of OTG. Earlier, these parameters were not modifiable for any platform data. It was reading from the HW and then was programming the same value again. Now, it has been modified. A platform code can modify these parameters. Struct definition has been moved from cil.h to a new file include/linux/usb/dwc_otg.h. Some of the parameters have been initialized with default values, while other with -1. A new parameter fifo_number has been added. This parameter is also defined in the specification. Otg code was reading number of endpoint from hwcfg regs for the purpose of this parameter, which was wrong. SW checks for only fifo_number fifos and not MAX_TX_FIFOS. Now , there is only one define for MAX_TX_FIFO and MAX_PERIO_FIFOS. As, per specification they can not be different. 11. In dwc_otg_pcd_handle_np_tx_fifo_empty_intr a different interrupt was cleared. Corrected it to clear NP TX Fifo empty interrupt. Re-enabling of interrupt was not correct when packets were still pending. This patch also corrects this behaviour. 12. Code checks for space availability in fifo during write_epmty_tx_fifo. It was writing only when space available was more than data to be written. So, it was writing 512 bytes only when 516 bytes space was available. Modified condition check from > to >=. 13. When TX fifo empty interrupt is received, transfer completion may not be true. Next transfer should only be started when transfer is complete, i.e. packet count in dieptsiz register has become zero. 14. Max number of EP increased to 16 15. There can be few devices like SPEAr1340, which issues a connection only after removal of soft disconnect. Default reset value is disconnected. It will not have any side effect even for the device where reset value is connected. 16. As per data sheet, when bit 31 of GRSTCTL is 1 then AHB is IDLE. Earlier function was waiting for this but to be 0, which was wrong. 17. Although name of file suggest that it is specific for PPC. But, all of its content are common for OTG and can be used for any platform. There were some compilation issued on ARM platform with this file. It has been removed by calling by proper functions. Pratyush Anand (4): dwc/otg: Structure declaration for shared data include/linux/usb/gadget.h : include <linux/device.h> for successful compilation usb/gadget/kconfig: added dwc otg as an option for peripheral controller arm/include/asm/io.h : added macros to read/write big/little endian register Tirumala Marri (10): dwc/otg: Add Register definitions dwc/otg: Add driver framework dwc/otg: Add Core Interface Layer (CIL) dwc/otg: Add HCD function dwc/otg: Add HCD interrupt function dwc/otg: Add HCD queue function dwc/otg: Add PCD function dwc/otg: Add PCD interrupt function dwc/otg: Add driver kernel configuration and Makefile dwc/otg: Driver enable gadget support arch/arm/include/asm/io.h | 8 + drivers/Makefile | 1 + drivers/usb/Kconfig | 2 + drivers/usb/dwc/Kconfig | 84 ++ drivers/usb/dwc/Makefile | 19 + drivers/usb/dwc/apmppc.c | 436 +++++++ drivers/usb/dwc/cil.c | 969 +++++++++++++++ drivers/usb/dwc/cil.h | 921 ++++++++++++++ drivers/usb/dwc/cil_intr.c | 616 +++++++++ drivers/usb/dwc/driver.h | 76 ++ drivers/usb/dwc/hcd.c | 2465 +++++++++++++++++++++++++++++++++++++ drivers/usb/dwc/hcd.h | 416 +++++++ drivers/usb/dwc/hcd_intr.c | 1481 ++++++++++++++++++++++ drivers/usb/dwc/hcd_queue.c | 696 +++++++++++ drivers/usb/dwc/param.c | 219 ++++ drivers/usb/dwc/pcd.c | 1818 +++++++++++++++++++++++++++ drivers/usb/dwc/pcd.h | 139 +++ drivers/usb/dwc/pcd_intr.c | 2316 ++++++++++++++++++++++++++++++++++ drivers/usb/dwc/regs.h | 1324 ++++++++++++++++++++ drivers/usb/gadget/Kconfig | 17 + drivers/usb/gadget/gadget_chips.h | 18 +- include/linux/usb/dwc_otg.h | 274 ++++ include/linux/usb/gadget.h | 1 + 23 files changed, 14315 insertions(+), 1 deletions(-) create mode 100644 drivers/usb/dwc/Kconfig create mode 100644 drivers/usb/dwc/Makefile create mode 100644 drivers/usb/dwc/apmppc.c create mode 100644 drivers/usb/dwc/cil.c create mode 100644 drivers/usb/dwc/cil.h create mode 100644 drivers/usb/dwc/cil_intr.c create mode 100644 drivers/usb/dwc/driver.h create mode 100644 drivers/usb/dwc/hcd.c create mode 100644 drivers/usb/dwc/hcd.h create mode 100644 drivers/usb/dwc/hcd_intr.c create mode 100644 drivers/usb/dwc/hcd_queue.c create mode 100644 drivers/usb/dwc/param.c create mode 100644 drivers/usb/dwc/pcd.c create mode 100644 drivers/usb/dwc/pcd.h create mode 100644 drivers/usb/dwc/pcd_intr.c create mode 100644 drivers/usb/dwc/regs.h create mode 100644 include/linux/usb/dwc_otg.h -- 1.7.2.2 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
