On Thu, Jul 21, 2011 at 02:05:36PM -0700, Sarah Sharp wrote:
> On Thu, Jul 21, 2011 at 04:33:19PM -0400, Don Zickus wrote:
> > Hi Sarah,
> >
> > I am trying to debug a situation where when booting up my system with
> > 3.0.0-rc7, the xhci_hcd detects my usb3 WD disk and usb3 hub. However it
> > doesn't detect my usb3 Buffalo disk behind my hub.
>
> Does it detect other USB 3.0 devices behind the hub? What about USB 2.0
> devices?
I didn't have any other behind there. I did re-try my test with usb2.0
flash stick with no luck. I then switched to the TI prototype hub (you
probably have the same one I do) and had success with the usb3 disk but
not with the usb2 flash. :-/
>
> > On my Panther point system's root hub
> > port 3 has the WD disk
> > port 4 has the VIA 4-port usb3 hub
> >
> > Using lsusb -t, I expected bit0 to represent the actual connect state of
> > the device under the hub port status. It shows a '0', meaning nothing is
> > connected (for the VIA hub).
> >
> > Hub Port Status:
> > Port 1: 0000.02a0 5Gbps power Rx.Detect
> > Port 2: 0000.02a0 5Gbps power Rx.Detect
> > Port 3: 0000.02a0 5Gbps power Rx.Detect
> > Port 4: 0000.02a0 5Gbps power Rx.Detect
> >
> >
> > Of course, if I unplug the disk and re-connect, it works as expected.
> >
> > I am trying to understand the situation in which the hub would not see a
> > device is connected (even when the power is enabled to the port it seems).
>
> SuperSpeed devices have to go through link training with the downstream
> port on their parent hub. So a device can be connected and powered, but
> fail to train at SuperSpeed. At that point, the device is supposed to
> fall back to High Speed. At the next device reset, the device attempts
> to link train to SuperSpeed again.
>
> It's entirely possible the device or the hub is failing to link train
> properly, and the device gets stuck in SuperSpeed mode somehow.
>
> Do you have a hub from a different vendor to try out? If not, I can dig
> up a TI prototype one and try it on my own Panther Point system.
>
> > I am not sure what logs to attach so I haven't attached any.
>
> dmesg would work.
heh. of course. I attached that below. I believe all the stall and
short transfers at the bottom of the log are the result of numerous 'lsusb
-v' commands (or with -t too).
Cheers,
Don
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 3.0.0-rc7tip+ (dzickus@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.4 20100726 (Red Hat 4.4.4-13) (GCC) ) #368 SMP Wed Jul 20 15:51:39 EDT 2011
Command line: ro root=/dev/mapper/vg_intelsugarbaydh04-lv_root rd_LVM_LV=vg_intelsugarbaydh04/lv_root rd_LVM_LV=vg_intelsugarbaydh04/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us console=ttyS0,115200n81 crashkernel=auto earlycon=uart8250,io,0x2050,115200n81
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ac00 (usable)
BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000ad971000 (usable)
BIOS-e820: 00000000ad971000 - 00000000ad977000 (reserved)
BIOS-e820: 00000000ad977000 - 00000000af016000 (usable)
BIOS-e820: 00000000af016000 - 00000000af57a000 (reserved)
BIOS-e820: 00000000af57a000 - 00000000af7fa000 (ACPI NVS)
BIOS-e820: 00000000af7fa000 - 00000000af7ff000 (ACPI data)
BIOS-e820: 00000000af7ff000 - 00000000af800000 (usable)
BIOS-e820: 00000000af800000 - 00000000b0000000 (reserved)
BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff980000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000014e000000 (usable)
Early serial console at I/O port 0x2050 (options '115200n81')
bootconsole [uart0] enabled
NX (Execute Disable) protection: active
DMI 2.6 present.
DMI: Intel Corporation 2012 Client Platform/LosLunas CRB, BIOS ACRVMBY1.86C.0044.B01.1105201033 05/20/2011
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x14e000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-E7FFF uncachable
E8000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 0FFC00000 mask FFFC00000 write-protect
1 base 000000000 mask F80000000 write-back
2 base 080000000 mask FE0000000 write-back
3 base 0A0000000 mask FF0000000 write-back
4 base 0AF800000 mask FFF800000 uncachable
5 base 100000000 mask FC0000000 write-back
6 base 140000000 mask FF0000000 write-back
7 base 14E000000 mask FFE000000 uncachable
8 disabled
9 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
last_pfn = 0xaf800 max_arch_pfn = 0x400000000
found SMP MP-table at [ffff8800000fca40] fca40
initial memory mapped : 0 - 20000000
Base memory trampoline at [ffff880000095000] 95000 size 20480
init_memory_mapping: 0000000000000000-00000000af800000
0000000000 - 00af800000 page 2M
kernel direct mapping tables up to af800000 @ af012000-af016000
init_memory_mapping: 0000000100000000-000000014e000000
0100000000 - 014e000000 page 2M
kernel direct mapping tables up to 14e000000 @ 14dff9000-14e000000
RAMDISK: 37a02000 - 37ff0000
crashkernel: memory value expected
ACPI: RSDP 00000000000f0410 00024 (v02 INTEL)
ACPI: XSDT 00000000af7fde18 00074 (v01 INTEL IVB-CPT 06222004 MSFT 00010013)
ACPI: FACP 00000000af7e3d98 000F4 (v04 INTEL IVB-CPT 06222004 MSFT 00010013)
ACPI: DSDT 00000000af7c3018 0F56E (v02 INTEL IVB-CPT 00000000 INTL 20100806)
ACPI: FACS 00000000af7f9e40 00040
ACPI: APIC 00000000af7fcf18 000CC (v02 INTEL IVB-CPT 06222004 MSFT 00010013)
ACPI: HPET 00000000af7f8f18 00038 (v01 A M I PCHHPET 06222004 AMI. 00000003)
ACPI: SSDT 00000000af7e5018 010A8 (v01 TrmRef PtidDevc 00001000 INTL 20100806)
ACPI: SSDT 00000000af7e4918 003FF (v01 AMI PerfTune 00001000 INTL 20100806)
ACPI: BOOT 00000000af7f8e98 00028 (v01 INTEL IVB-CPT 06222004 AMI 00010013)
ACPI: MCFG 00000000af7f8e18 0003C (v01 INTEL SNDYBRDG 06222004 MSFT 00000097)
ACPI: SSDT 00000000af7f7798 006FC (v01 PmRef Cpu0Ist 00003000 INTL 20100806)
ACPI: SSDT 00000000af7f6018 00A2C (v01 PmRef CpuPm 00003000 INTL 20100806)
ACPI: DMAR 00000000af7f7f18 000B0 (v01 INTEL SNB 00000001 INTL 00000001)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-000000014e000000
Initmem setup node 0 0000000000000000-000000014e000000
NODE_DATA [000000014dfd2000 - 000000014dff8fff]
[ffffea0000000000-ffffea00049fffff] PMD -> [ffff880149600000-ffff88014cffffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0014e000
Movable zone start PFN for each node
early_node_map[5] active PFN ranges
0: 0x00000010 -> 0x0000009a
0: 0x00000100 -> 0x000ad971
0: 0x000ad977 -> 0x000af016
0: 0x000af7ff -> 0x000af800
0: 0x00100000 -> 0x0014e000
On node 0 totalpages: 1036187
DMA zone: 56 pages used for memmap
DMA zone: 5 pages reserved
DMA zone: 3917 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 698441 pages, LIFO batch:31
Normal zone: 4368 pages used for memmap
Normal zone: 315120 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] disabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x08] disabled)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x09] disabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0a] disabled)
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0b] disabled)
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0c] disabled)
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0d] disabled)
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0e] disabled)
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x0f] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a701 base: 0xfed00000
SMP: Allowing 16 CPUs, 12 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: 000000000009a000 - 000000000009b000
PM: Registered nosave memory: 000000000009b000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000ad971000 - 00000000ad977000
PM: Registered nosave memory: 00000000af016000 - 00000000af57a000
PM: Registered nosave memory: 00000000af57a000 - 00000000af7fa000
PM: Registered nosave memory: 00000000af7fa000 - 00000000af7ff000
PM: Registered nosave memory: 00000000af800000 - 00000000b0000000
PM: Registered nosave memory: 00000000b0000000 - 00000000f8000000
PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ff980000
PM: Registered nosave memory: 00000000ff980000 - 00000000ffc00000
PM: Registered nosave memory: 00000000ffc00000 - 00000000ffd80000
PM: Registered nosave memory: 00000000ffd80000 - 0000000100000000
Allocating PCI resources starting at b0000000 (gap: b0000000:48000000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:4096 nr_cpumask_bits:16 nr_cpu_ids:16 nr_node_ids:1
PERCPU: Embedded 27 pages/cpu @ffff88014dc00000 s81280 r8192 d21120 u131072
pcpu-alloc: s81280 r8192 d21120 u131072 alloc=1*2097152
pcpu-alloc: [0] 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15
Built 1 zonelists in Node order, mobility grouping on. Total pages: 1017478
Policy zone: Normal
Kernel command line: ro root=/dev/mapper/vg_intelsugarbaydh04-lv_root rd_LVM_LV=vg_intelsugarbaydh04/lv_root rd_LVM_LV=vg_intelsugarbaydh04/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us console=ttyS0,115200n81 crashkernel=auto earlycon=uart8250,io,0x2050,115200n81
PID hash table entries: 4096 (order: 3, 32768 bytes)
xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
Checking aperture...
No AGP bridge found
Queued invalidation will be enabled to support x2apic and Intr-remapping.
Memory: 3987720k/5472256k available (5067k kernel code, 1327508k absent, 157028k reserved, 7349k data, 1580k init)
Hierarchical RCU implementation.
NR_IRQS:262400 nr_irqs:808 16
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [ttyS0] enabled, bootconsole disabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 16384
... MAX_LOCKDEP_CHAINS: 32768
... CHAINHASH_SIZE: 16384
memory used by lock dependency info: 5823 kB
per task-struct memory footprint: 1920 bytes
allocated 33554432 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 1795.982 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3591.96 BogoMIPS (lpj=1795982)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 7 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20110413
ftrace: allocating 19473 entries in 77 pages
DMAR: Host address width 36
DMAR: DRHD base: 0x000000fed90000 flags: 0x1
IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c9008020660262 ecap f0105a
DMAR: RMRR base: 0x000000af4c1000 end: 0x000000af4d7fff
DMAR: No ATSR found
IOAPIC id 2 under DRHD base 0xfed90000 IOMMU 0
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
HPET id 0 under DRHD base 0xfed90000
Enabled Interrupt-remapping
Enabling x2apic
Enabled x2apic
Switched APIC routing to cluster x2apic.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Genuine Intel(R) CPU @ 1.80GHz stepping 02
Performance Events: PEBS fmt1+, generic architected perfmon, Intel PMU driver.
... version: 3
... bit width: 48
... generic registers: 4
... value mask: 0000ffffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 000000070000000f
NMI watchdog enabled, takes one hw-pmu counter.
lockdep: fixing up alternatives.
Booting Node 0, Processors #1
smpboot cpu 1: start_ip = 95000
NMI watchdog enabled, takes one hw-pmu counter.
lockdep: fixing up alternatives.
#2
smpboot cpu 2: start_ip = 95000
NMI watchdog enabled, takes one hw-pmu counter.
lockdep: fixing up alternatives.
#3
smpboot cpu 3: start_ip = 95000
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 4 CPUs
Total of 4 processors activated (14366.14 BogoMIPS).
devtmpfs: initialized
PM: Registering ACPI NVS region at af57a000 (2621440 bytes)
print_constraints: dummy:
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: SSDT 00000000af4bf018 008EB (v01 PmRef Cpu0Cst 00003001 INTL 20100806)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 008EB (v01 PmRef Cpu0Cst 00003001 INTL 20100806)
ACPI: SSDT 00000000af4c0a98 00303 (v01 PmRef ApIst 00003000 INTL 20100806)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20100806)
ACPI: SSDT 00000000af4bed98 00119 (v01 PmRef ApCst 00003000 INTL 20100806)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20100806)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: Power Resource [FN00] (off)
ACPI: Power Resource [FN01] (off)
ACPI: Power Resource [FN02] (off)
ACPI: Power Resource [FN03] (off)
ACPI: Power Resource [FN04] (off)
ACPI: ACPI Dock Station Driver: 1 docks/bays found
HEST: Table not found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
\_SB_.PCI0:_OSC invalid UUID
_OSC request data:1 8 1f
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
pci_root PNP0A08:00: host bridge window [mem 0xb0000000-0xfeafffff]
pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
pci 0000:00:00.0: [8086:0150] type 0 class 0x000600
pci 0000:00:01.0: [8086:0151] type 1 class 0x000604
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:14.0: [8086:1e31] type 0 class 0x000c03
pci 0000:00:14.0: reg 10: [mem 0xb11b0000-0xb11bffff 64bit]
pci 0000:00:14.0: PME# supported from D3hot D3cold
pci 0000:00:14.0: PME# disabled
pci 0000:00:16.0: [8086:1e3a] type 0 class 0x000780
pci 0000:00:16.0: reg 10: [mem 0xb11a0000-0xb11a000f 64bit]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:16.0: PME# disabled
pci 0000:00:19.0: [8086:1502] type 0 class 0x000200
pci 0000:00:19.0: reg 10: [mem 0xb1100000-0xb111ffff]
pci 0000:00:19.0: reg 14: [mem 0xb1180000-0xb1180fff]
pci 0000:00:19.0: reg 18: [io 0x4040-0x405f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: [8086:1e2d] type 0 class 0x000c03
pci 0000:00:1a.0: reg 10: [mem 0xb1170000-0xb11703ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1b.0: [8086:1e20] type 0 class 0x000403
pci 0000:00:1b.0: reg 10: [mem 0xb1160000-0xb1163fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: [8086:1e10] type 1 class 0x000604
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1d.0: [8086:1e26] type 0 class 0x000c03
pci 0000:00:1d.0: reg 10: [mem 0xb1150000-0xb11503ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
pci 0000:00:1f.0: [8086:1e47] type 0 class 0x000601
pci 0000:00:1f.2: [8086:1e02] type 0 class 0x000106
pci 0000:00:1f.2: reg 10: [io 0x4090-0x4097]
pci 0000:00:1f.2: reg 14: [io 0x4080-0x4083]
pci 0000:00:1f.2: reg 18: [io 0x4070-0x4077]
pci 0000:00:1f.2: reg 1c: [io 0x4060-0x4063]
pci 0000:00:1f.2: reg 20: [io 0x4020-0x403f]
pci 0000:00:1f.2: reg 24: [mem 0xb1140000-0xb11407ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: [8086:1e22] type 0 class 0x000c05
pci 0000:00:1f.3: reg 10: [mem 0xb1130000-0xb11300ff 64bit]
pci 0000:00:1f.3: reg 20: [io 0x4000-0x401f]
pci 0000:01:00.0: [10de:0a65] type 0 class 0x000300
pci 0000:01:00.0: reg 10: [mem 0xb0000000-0xb0ffffff]
pci 0000:01:00.0: reg 14: [mem 0xc0000000-0xcfffffff 64bit pref]
pci 0000:01:00.0: reg 1c: [mem 0xd0000000-0xd1ffffff 64bit pref]
pci 0000:01:00.0: reg 24: [io 0x3000-0x307f]
pci 0000:01:00.0: reg 30: [mem 0xb1000000-0xb107ffff pref]
pci 0000:01:00.1: [10de:0be3] type 0 class 0x000403
pci 0000:01:00.1: reg 10: [mem 0xb1080000-0xb1083fff]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:01.0: bridge window [mem 0xb0000000-0xb10fffff]
pci 0000:00:01.0: bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:01.0: [9710:9835] type 0 class 0x000700
pci 0000:03:01.0: reg 10: [io 0x2050-0x2057]
pci 0000:03:01.0: reg 14: [io 0x2040-0x2047]
pci 0000:03:01.0: reg 18: [io 0x2030-0x2037]
pci 0000:03:01.0: reg 1c: [io 0x2020-0x2027]
pci 0000:03:01.0: reg 20: [io 0x2010-0x2017]
pci 0000:03:01.0: reg 24: [io 0x2000-0x200f]
pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xb0000000-0xfeafffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT]
\_SB_.PCI0:_OSC invalid UUID
_OSC request data:1 1f 1f
pci0000:00: Requesting ACPI _OSC control (0x1d)
\_SB_.PCI0:_OSC invalid UUID
_OSC request data:1 0 1d
pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
ACPI _OSC control for PCIe not granted, disabling ASPM
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:01:00.0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009ac00 - 000000000009ffff
reserve RAM buffer: 00000000ad971000 - 00000000afffffff
reserve RAM buffer: 00000000af016000 - 00000000afffffff
reserve RAM buffer: 00000000af800000 - 00000000afffffff
reserve RAM buffer: 000000014e000000 - 000000014fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource hpet
Switched to NOHz mode on CPU #0
Switched to NOHz mode on CPU #2
Switched to NOHz mode on CPU #1
Switched to NOHz mode on CPU #3
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [bus 00-3e]
pnp 00:00: [io 0x0000-0x0cf7 window]
pnp 00:00: [io 0x0cf8-0x0cff]
pnp 00:00: [io 0x0d00-0xffff window]
pnp 00:00: [mem 0x000a0000-0x000bffff window]
pnp 00:00: [mem 0x000c0000-0x000c3fff window]
pnp 00:00: [mem 0x000c4000-0x000c7fff window]
pnp 00:00: [mem 0x000c8000-0x000cbfff window]
pnp 00:00: [mem 0x000cc000-0x000cffff window]
pnp 00:00: [mem 0x000d0000-0x000d3fff window]
pnp 00:00: [mem 0x000d4000-0x000d7fff window]
pnp 00:00: [mem 0x000d8000-0x000dbfff window]
pnp 00:00: [mem 0x000dc000-0x000dffff window]
pnp 00:00: [mem 0x000e0000-0x000e3fff window]
pnp 00:00: [mem 0x000e4000-0x000e7fff window]
pnp 00:00: [mem 0x000e8000-0x000ebfff window]
pnp 00:00: [mem 0x000ec000-0x000effff window]
pnp 00:00: [mem 0x000f0000-0x000fffff window]
pnp 00:00: [mem 0xb0000000-0xfeafffff window]
pnp 00:00: [mem 0xfed40000-0xfed44fff window]
pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
pnp 00:01: [io 0x0000-0x001f]
pnp 00:01: [io 0x0081-0x0091]
pnp 00:01: [io 0x0093-0x009f]
pnp 00:01: [io 0x00c0-0x00df]
pnp 00:01: [dma 4]
pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:02: [mem 0xff000000-0xffffffff]
pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
pnp 00:03: [mem 0xfed00000-0xfed003ff]
pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
pnp 00:04: [io 0x00f0]
pnp 00:04: [irq 13]
pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:05: [io 0x002e-0x002f]
pnp 00:05: [io 0x004e-0x004f]
pnp 00:05: [io 0x0061]
pnp 00:05: [io 0x0063]
pnp 00:05: [io 0x0065]
pnp 00:05: [io 0x0067]
pnp 00:05: [io 0x0070]
pnp 00:05: [io 0x0080]
pnp 00:05: [io 0x0092]
pnp 00:05: [io 0x00b2-0x00b3]
pnp 00:05: [io 0x0680-0x069f]
pnp 00:05: [io 0x1000-0x100f]
pnp 00:05: [io 0xffff]
pnp 00:05: [io 0xffff]
pnp 00:05: [io 0x0400-0x0453]
pnp 00:05: [io 0x0458-0x047f]
pnp 00:05: [io 0x0500-0x057f]
pnp 00:05: [io 0x164e-0x164f]
system 00:05: [io 0x0680-0x069f] has been reserved
system 00:05: [io 0x1000-0x100f] has been reserved
system 00:05: [io 0xffff] has been reserved
system 00:05: [io 0xffff] has been reserved
system 00:05: [io 0x0400-0x0453] has been reserved
system 00:05: [io 0x0458-0x047f] has been reserved
system 00:05: [io 0x0500-0x057f] has been reserved
system 00:05: [io 0x164e-0x164f] has been reserved
system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:06: [io 0x0070-0x0077]
pnp 00:06: [irq 8]
pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:07: [io 0x0454-0x0457]
system 00:07: [io 0x0454-0x0457] has been reserved
system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
pnp 00:08: [mem 0xfed10000-0xfed17fff]
pnp 00:08: [mem 0xfed18000-0xfed18fff]
pnp 00:08: [mem 0xfed19000-0xfed19fff]
pnp 00:08: [mem 0xf8000000-0xfbffffff]
pnp 00:08: [mem 0xfed20000-0xfed3ffff]
pnp 00:08: [mem 0xfed90000-0xfed93fff]
pnp 00:08: [mem 0xfed45000-0xfed8ffff]
pnp 00:08: [mem 0xff000000-0xffffffff]
pnp 00:08: [mem 0xfee00000-0xfeefffff]
pnp 00:08: [mem 0xb11c0000-0xb11c0fff]
pnp 00:08: [mem 0x00000000-0xffffffffffffffff disabled]
system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:08: [mem 0xfed10000-0xfed17fff] could not be reserved
system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:08: [mem 0xf8000000-0xfbffffff] has been reserved
system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
system 00:08: [mem 0xff000000-0xffffffff] could not be reserved
system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
system 00:08: [mem 0xb11c0000-0xb11c0fff] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: [mem 0x00000000-0x0009cfff]
system 00:09: [mem 0x00000000-0x0009cfff] could not be reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
pci 0000:00:01.0: bridge window [mem 0xb0000000-0xb10fffff]
pci 0000:00:01.0: bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0: bridge window [io disabled]
pci 0000:00:1c.0: bridge window [mem disabled]
pci 0000:00:1c.0: bridge window [mem pref disabled]
pci 0000:00:1e.0: PCI bridge to [bus 03-03]
pci 0000:00:1e.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:1e.0: bridge window [mem disabled]
pci 0000:00:1e.0: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff]
pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff]
pci_bus 0000:00: resource 13 [mem 0xb0000000-0xfeafffff]
pci_bus 0000:00: resource 14 [mem 0xfed40000-0xfed44fff]
pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:01: resource 1 [mem 0xb0000000-0xb10fffff]
pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
pci_bus 0000:03: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000d3fff]
pci_bus 0000:03: resource 8 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:03: resource 9 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:03: resource 10 [mem 0x000dc000-0x000dffff]
pci_bus 0000:03: resource 11 [mem 0x000e0000-0x000e3fff]
pci_bus 0000:03: resource 12 [mem 0x000e4000-0x000e7fff]
pci_bus 0000:03: resource 13 [mem 0xb0000000-0xfeafffff]
pci_bus 0000:03: resource 14 [mem 0xfed40000-0xfed44fff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 10, 4194304 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 2048 (order: 6, 327680 bytes)
UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes)
NET: Registered protocol family 1
pci 0000:01:00.0: Boot video device
PCI: CLS 64 bytes, default 64
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 6072k freed
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff8800a9971000 - ffff8800ad971000
software IO TLB at phys 0xa9971000 - 0xad971000
Simple Boot Flag at 0x4f set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1311264996.636:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 7800
SELinux: Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:01.0: setting latency timer to 64
pcieport 0000:00:01.0: irq 41 for MSI/MSI-X
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
acpiphp: Slot [1] registered
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: Fan [FAN2] (off)
ACPI: Fan [FAN3] (off)
ACPI: Fan [FAN4] (off)
ACPI: acpi_idle registered with cpuidle
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [TZ00] (28 C)
thermal LNXTHERM:01: registered as thermal_zone1
ACPI: Thermal Zone [TZ01] (30 C)
ERST: Table is not found!
GHES: HEST is not enabled!
EINJ: Table is not found!
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial 0000:03:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
0000:03:01.0: ttyS0 at I/O 0x2050 (irq = 22) is a 16550A
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
brd: module loaded
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xb1140000 port 0xb1140100 irq 42
ata2: DUMMY
ata3: SATA max UDMA/133 abar m2048@0xb1140000 port 0xb1140200 irq 42
ata4: DUMMY
ata5: DUMMY
ata6: DUMMY
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.0: irq 16, io mem 0xb1170000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.0.0-rc7tip+ ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xb1150000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 3.0.0-rc7tip+ ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
i8042: PNP: No PS/2 controller found. Probing ports directly.
i8042: No controller found
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
EFI Variables Facility v0.08 2004-May-17
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Registering the dns_resolver key type
registered taskstats version 1
IMA: No TPM chip found, activating TPM-bypass!
rtc_cmos 00:06: setting system clock to 2011-07-21 16:16:37 UTC (1311264997)
Initializing network drop monitor service
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-6: ST3120026AS, 3.00, max UDMA/133
ata3.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: ATAPI: Optiarc DVD RW AD-7200S, 1.0A, max UDMA/100
ata1.00: configured for UDMA/100
ata3.00: configured for UDMA/133
scsi 0:0:0:0: CD-ROM Optiarc DVD RW AD-7200S 1.0A PQ: 0 ANSI: 5
scsi 2:0:0:0: Direct-Access ATA ST3120026AS 3.00 PQ: 0 ANSI: 5
Freeing unused kernel memory: 1580k freed
Write protecting the kernel read-only data: 10240k
Freeing unused kernel memory: 1056k freed
Freeing unused kernel memory: 1692k freed
usb 1-1: new high speed USB device number 2 using ehci_hcd
dracut: dracut-004-53.el6
dracut: rd_NO_LUKS: removing cryptoluks activation
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@xxxxxxxxxx
udev: starting version 147
udevd (98): /proc/98/oom_adj is deprecated, please use /proc/98/oom_score_adj instead.
wmi: Mapper loaded
[drm] Initialized drm 1.1.0 20060810
usb 1-1: New USB device found, idVendor=8087, idProduct=0024
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nouveau 0000:01:00.0: setting latency timer to 64
[drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x0a8280b1)
[drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
usb 2-1: new high speed USB device number 2 using ehci_hcd
[drm] nouveau 0000:01:00.0: ... appears to be valid
[drm] nouveau 0000:01:00.0: BIT BIOS found
[drm] nouveau 0000:01:00.0: Bios version 70.18.5f.00
[drm] nouveau 0000:01:00.0: Pointer to BIT loadval table invalid
[drm] nouveau 0000:01:00.0: TMDS table version 2.0
[drm] nouveau 0000:01:00.0: Found Display Configuration Block version 4.0
[drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000302 00020030
[drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02000300 00000000
[drm] nouveau 0000:01:00.0: Raw DCB entry 2: 02011362 00020010
[drm] nouveau 0000:01:00.0: Raw DCB entry 3: 01022310 00000000
[drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 16 4
[drm] nouveau 0000:01:00.0: 0: 0x00001030: type 0x30 idx 0 tag 0x07
[drm] nouveau 0000:01:00.0: 1: 0x00002161: type 0x61 idx 1 tag 0x08
[drm] nouveau 0000:01:00.0: 2: 0x00000200: type 0x00 idx 2 tag 0xff
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD97D
[drm] nouveau 0000:01:00.0: 0xDC4A: Condition still not met after 20ms, skipping following opcodes
[drm] nouveau 0000:01:00.0: 0xDC4E: Condition still not met after 20ms, skipping following opcodes
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDE28
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xE9FB
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEA14
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEAFB
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEB60
[drm] nouveau 0000:01:00.0: 0xD7F1: Condition still not met after 20ms, skipping following opcodes
Refined TSC clocksource calibration: 1795.918 MHz.
Switching to clocksource tsc
usb 2-1: New USB device found, idVendor=8087, idProduct=0024
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
usb 1-1.5: new low speed USB device number 3 using ehci_hcd
[drm] nouveau 0000:01:00.0: 3 available performance level(s)
[drm] nouveau 0000:01:00.0: 0: memory 135MHz core 135MHz shader 270MHz voltage 850mV timing 0
[drm] nouveau 0000:01:00.0: 1: memory 405MHz core 405MHz shader 810MHz voltage 900mV timing 1
[drm] nouveau 0000:01:00.0: 3: memory 600MHz core 520MHz shader 1238MHz voltage 1000mV timing 3
[drm] nouveau 0000:01:00.0: c: memory 405MHz core 405MHz shader 810MHz voltage 900mV
[TTM] Zone kernel: Available graphics memory: 1999060 kiB.
[TTM] Initializing pool allocator.
[drm] nouveau 0000:01:00.0: memory controller reports 512MiB VRAM
[drm] nouveau 0000:01:00.0: we calculated 1024MiB VRAM
[drm] nouveau 0000:01:00.0: Detected 512MiB VRAM
[drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
usb 1-1.5: New USB device found, idVendor=0624, idProduct=0291
usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.5: Product: Avocent AVRIQ-USB
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
usb 1-1.5: Manufacturer: Avocent
input: Avocent Avocent AVRIQ-USB as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input1
generic-usb 0003:0624:0291.0001: input,hidraw0: USB HID v1.10 Keyboard [Avocent Avocent AVRIQ-USB] on usb-0000:00:1a.0-1.5/input0
input: Avocent Avocent AVRIQ-USB as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.1/input/input2
generic-usb 0003:0624:0291.0002: input,hidraw1: USB HID v1.10 Mouse [Avocent Avocent AVRIQ-USB] on usb-0000:00:1a.0-1.5/input1
[drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x40000000, bo ffff880143f20800
fbcon: nouveaufb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
fb0: nouveaufb frame buffer device
drm: registered panic notifier
[drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0
dracut: Starting plymouth daemon
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
dracut: Scanning devices sda2 for LVM logical volumes vg_intelsugarbaydh04/lv_root vg_intelsugarbaydh04/lv_swap
dracut: inactive '/dev/vg_intelsugarbaydh04/lv_root' [50.00 GiB] inherit
dracut: inactive '/dev/vg_intelsugarbaydh04/lv_home' [55.47 GiB] inherit
dracut: inactive '/dev/vg_intelsugarbaydh04/lv_swap' [5.83 GiB] inherit
EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
dracut: Mounted root filesystem /dev/mapper/vg_intelsugarbaydh04-lv_root
dracut: Loading SELinux policy
type=1404 audit(1311265000.065:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 2048 avtab hash slots, 211951 rules.
SELinux: 2048 avtab hash slots, 211951 rules.
SELinux: 9 users, 13 roles, 3426 types, 178 bools, 1 sens, 1024 cats
SELinux: 81 classes, 211951 rules
SELinux: Permission audit_access in class file not defined in policy.
SELinux: Permission audit_access in class dir not defined in policy.
SELinux: Permission execmod in class dir not defined in policy.
SELinux: Permission audit_access in class lnk_file not defined in policy.
SELinux: Permission open in class lnk_file not defined in policy.
SELinux: Permission execmod in class lnk_file not defined in policy.
SELinux: Permission audit_access in class chr_file not defined in policy.
SELinux: Permission audit_access in class blk_file not defined in policy.
SELinux: Permission execmod in class blk_file not defined in policy.
SELinux: Permission audit_access in class sock_file not defined in policy.
SELinux: Permission execmod in class sock_file not defined in policy.
SELinux: Permission audit_access in class fifo_file not defined in policy.
SELinux: Permission execmod in class fifo_file not defined in policy.
SELinux: Permission syslog in class capability2 not defined in policy.
SELinux: the above unknown classes and permissions will be allowed
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev dm-0, type ext4), uses xattr
type=1403 audit(1311265000.752:3): policy loaded auid=4294967295 ses=4294967295
dracut:
dracut: Switching root
readahead-collector: starting
udev: starting version 147
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
hda_codec: ALC889: BIOS auto-probing.
hda_codec: ALC889: SKU not ready 0x598301f0
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3
audit: name_count maxed, losing inode data: dev=00:05, inode=9386
HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
hda_intel: Disabling MSI
HDA Intel 0000:01:00.1: setting latency timer to 64
HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input4
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input5
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input6
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input7
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
audit: name_count maxed, losing inode data: dev=00:05, inode=6258
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
audit: name_count maxed, losing inode data: dev=00:05, inode=9376
e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: setting latency timer to 64
e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:13:20:f9:d5:82
e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
xhci_hcd 0000:00:14.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
xhci_hcd 0000:00:14.0: setting latency timer to 64
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
xhci_hcd 0000:00:14.0: irq 21, io mem 0xb11b0000
xhci_hcd 0000:00:14.0: Failed to enable MSI-X
xhci_hcd 0000:00:14.0: irq 45 for MSI/MSI-X
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 3.0.0-rc7tip+ xhci_hcd
usb usb3: SerialNumber: 0000:00:14.0
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
xhci_hcd 0000:00:14.0: xHCI Host Controller
audit: name_count maxed, losing inode data: dev=00:06, inode=9459
audit: name_count maxed, losing inode data: dev=00:06, inode=6234
audit: name_count maxed, losing inode data: dev=00:05, inode=3
audit: name_count maxed, losing inode data: dev=00:05, inode=3
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 3.0.0-rc7tip+ xhci_hcd
usb usb4: SerialNumber: 0000:00:14.0
audit: name_count maxed, losing inode data: dev=00:05, inode=3
audit: name_count maxed, losing inode data: dev=00:05, inode=6245
audit: name_count maxed, losing inode data: dev=00:05, inode=6246
audit: name_count maxed, losing inode data: dev=00:05, inode=6246
audit: name_count maxed, losing inode data: dev=00:05, inode=9462
audit: name_count maxed, losing inode data: dev=00:05, inode=9462
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
input: PC Speaker as /devices/platform/pcspkr/input/input8
microcode: CPU0 sig=0x306a2, pf=0x2, revision=0x8
microcode: CPU1 sig=0x306a2, pf=0x2, revision=0x8
usb 3-3: new high speed USB device number 2 using xhci_hcd
usb 3-3: Device not responding to set address.
microcode: CPU2 sig=0x306a2, pf=0x2, revision=0x8
microcode: CPU3 sig=0x306a2, pf=0x2, revision=0x8
microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
sr 0:0:0:0: Attached scsi generic sg0 type 5
sd 2:0:0:0: Attached scsi generic sg1 type 0
usb 3-3: Device not responding to set address.
usb 3-3: device not accepting address 2, error -71
hub 3-0:1.0: unable to enumerate USB device on port 3
usb 3-4: new high speed USB device number 4 using xhci_hcd
usb 3-4: Device not responding to set address.
usb 3-4: Device not responding to set address.
usb 3-4: device not accepting address 4, error -71
usb 3-4: new high speed USB device number 5 using xhci_hcd
usb 3-4: Device not responding to set address.
usb 3-4: Device not responding to set address.
usb 3-4: device not accepting address 5, error -71
usb 3-4: new high speed USB device number 6 using xhci_hcd
usb 3-4: Device not responding to set address.
usb 3-4: Device not responding to set address.
usb 3-4: device not accepting address 6, error -71
usb 3-4: new high speed USB device number 7 using xhci_hcd
usb 3-4: Device not responding to set address.
EXT4-fs (dm-0): re-mounted. Opts: (null)
usb 3-4: Device not responding to set address.
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
SELinux: initialized (dev sda1, type ext4), uses xattr
usb 3-4: device not accepting address 7, error -71
hub 3-0:1.0: unable to enumerate USB device on port 4
EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
SELinux: initialized (dev dm-2, type ext4), uses xattr
usb 4-3: new SuperSpeed USB device number 2 using xhci_hcd
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
usb 4-3: New USB device found, idVendor=1058, idProduct=0730
usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-3: Product: My Passport 0730
usb 4-3: Manufacturer: Western Digital
usb 4-3: SerialNumber: 575837314132314434373235
usb 4-4: new SuperSpeed USB device number 3 using xhci_hcd
Initializing USB Mass Storage driver...
scsi6 : usb-storage 4-3:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
usb 4-4: New USB device found, idVendor=2109, idProduct=0810
usb 4-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-4: Product: 4-Port USB 3.0 Hub
usb 4-4: Manufacturer: VIA Labs, Inc.
hub 4-4:1.0: USB hub found
hub 4-4:1.0: 4 ports detected
Adding 6111228k swap on /dev/mapper/vg_intelsugarbaydh04-lv_swap. Priority:-1 extents:1 across:6111228k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
readahead-disable-service: delaying service auditd
scsi 6:0:0:0: Direct-Access WD My Passport 0730 1015 PQ: 0 ANSI: 6
scsi 6:0:0:1: Enclosure WD SES Device 1015 PQ: 0 ANSI: 6
sd 6:0:0:0: Attached scsi generic sg2 type 0
sd 6:0:0:0: [sdb] 976707584 512-byte logical blocks: (500 GB/465 GiB)
sd 6:0:0:0: [sdb] Write Protect is off
scsi 6:0:0:1: Attached scsi generic sg3 type 13
sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
sd 6:0:0:0: [sdb] No Caching mode page present
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] No Caching mode page present
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1 sdb2
sd 6:0:0:0: [sdb] No Caching mode page present
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] Attached SCSI disk
ses 6:0:0:1: Attached Enclosure device
xhci_hcd 0000:00:14.0: WARN: Stalled endpoint
NET: Registered protocol family 10
e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
readahead-collector: starting delayed service auditd
readahead-collector: sorting
hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
readahead-collector: finished
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: Stalled endpoint
xhci_hcd 0000:00:14.0: WARN: Stalled endpoint
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: short transfer on control ep
xhci_hcd 0000:00:14.0: WARN: Stalled endpoint
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
