On Tue, Apr 26, 2011 at 7:10 PM, Menon, Nishanth <nm@xxxxxx> wrote:
> On Thu, Apr 21, 2011 at 09:22, Keshava Munegowda <keshava_mgowda@xxxxxx> wrote:
>>
>> From: Keshava Munegowda <Keshava_mgowda@xxxxxx>
>>
>> The gpio of EHCI phy should be 0 instead of 1;
>> This fixes the hub enumeration issue in beagle xm board.
>>
>> Signed-off-by: Keshava Munegowda <keshava_mgowda@xxxxxx>
>
> Dumb q1: Has this been tested on PandaBoard?
No, I have tested this on 4430 sdp . I think sdp validation is sufficient
> Dumb q2: is'nt it better to introduce polarity e.g.
> pdata->ehci_data->reset_gpio_polarity etc? this will allow board files
> to describe polarity of pin information to driver which can then be
> Phy and any board specific mods(e.g. inverter on the line) independent
> completely..
yes, I am thinking of doing it; since it requires modification of all
board files;
I will send this an another separate patch.
keshava munegowda
>
> Regards,
> Nishanth Menon
>
>> ---
>> drivers/mfd/omap-usb-host.c | 8 ++++----
>> 1 files changed, 4 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
>> index b3bb3ac..a12202e 100644
>> --- a/drivers/mfd/omap-usb-host.c
>> +++ b/drivers/mfd/omap-usb-host.c
>> @@ -718,14 +718,14 @@ static int usbhs_enable(struct device *dev)
>> gpio_request(pdata->ehci_data->reset_gpio_port[0],
>> "USB1 PHY reset");
>> gpio_direction_output
>> - (pdata->ehci_data->reset_gpio_port[0], 1);
>> + (pdata->ehci_data->reset_gpio_port[0], 0);
>> }
>>
>> if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1])) {
>> gpio_request(pdata->ehci_data->reset_gpio_port[1],
>> "USB2 PHY reset");
>> gpio_direction_output
>> - (pdata->ehci_data->reset_gpio_port[1], 1);
>> + (pdata->ehci_data->reset_gpio_port[1], 0);
>> }
>>
>> /* Hold the PHY in RESET for enough time till DIR is high */
>> @@ -905,11 +905,11 @@ static int usbhs_enable(struct device *dev)
>>
>> if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
>> gpio_set_value
>> - (pdata->ehci_data->reset_gpio_port[0], 0);
>> + (pdata->ehci_data->reset_gpio_port[0], 1);
>>
>> if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
>> gpio_set_value
>> - (pdata->ehci_data->reset_gpio_port[1], 0);
>> + (pdata->ehci_data->reset_gpio_port[1], 1);
>> }
>>
>> end_count:
>> --
>> 1.6.0.4
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
