This patch adds support for Set Port Feature(PORT_LINK_STATE) request.
The most significant byte (bits 15..8) of the wIndex field specifies
the U state the host software wants to put the link connected to the
port into. This request is only valid when the PORT_ENABLE bit is set
and the PORT_LINK_STATE should not be above value '5' (Rx.Detect).
This request will be later used to replace the set/clear suspend USB3
protocol ports in hub driver.
Signed-off-by: Andiry Xu <andiry.xu@xxxxxxx>
---
drivers/usb/host/xhci-hub.c | 41 +++++++++++++++++++++++++++++++++++++++++
1 files changed, 41 insertions(+), 0 deletions(-)
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index b9bd0a7..a0aa431 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -387,6 +387,7 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
u32 __iomem **port_array;
int slot_id;
struct xhci_bus_state *bus_state;
+ u16 link_state = 0;
if (hcd->speed == HCD_USB3) {
ports = xhci->num_usb3_ports;
@@ -497,6 +498,8 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
put_unaligned(cpu_to_le32(status), (__le32 *) buf);
break;
case SetPortFeature:
+ if (wValue == USB_PORT_FEAT_LINK_STATE)
+ link_state = (wIndex & 0xff00) >> 3;
wIndex &= 0xff;
if (!wIndex || wIndex > ports)
goto error;
@@ -545,6 +548,44 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
temp = xhci_readl(xhci, port_array[wIndex]);
bus_state->suspended_ports |= 1 << wIndex;
break;
+ case USB_PORT_FEAT_LINK_STATE:
+ temp = xhci_readl(xhci, port_array[wIndex]);
+ /* Software should not attempt to set
+ * port link state above '5' (Rx.Detect) and the port
+ * must be enabled.
+ */
+ if ((temp & PORT_PE) == 0 ||
+ (link_state > USB_SS_PORT_LS_RX_DETECT)) {
+ xhci_warn(xhci, "Cannot set link state.\n");
+ goto error;
+ }
+
+ if (link_state == USB_SS_PORT_LS_U3) {
+ slot_id = xhci_find_slot_id_by_port(hcd, xhci,
+ wIndex + 1);
+ if (slot_id) {
+ /* unlock to execute stop endpoint
+ * commands */
+ spin_unlock_irqrestore(&xhci->lock,
+ flags);
+ xhci_stop_device(xhci, slot_id, 1);
+ spin_lock_irqsave(&xhci->lock, flags);
+ }
+ }
+
+ temp = xhci_port_state_to_neutral(temp);
+ temp &= ~PORT_PLS_MASK;
+ temp |= PORT_LINK_STROBE | link_state;
+ xhci_writel(xhci, temp, port_array[wIndex]);
+
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ msleep(10); /* wait device to enter */
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ temp = xhci_readl(xhci, port_array[wIndex]);
+ if (link_state == USB_SS_PORT_LS_U3)
+ bus_state->suspended_ports |= 1 << wIndex;
+ break;
case USB_PORT_FEAT_POWER:
/*
* Turn on ports, even if there isn't per-port switching.
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
