On Tue, Feb 22, 2011 at 09:05:33PM +0530, Anoop P.A wrote:
> From: Anoop <paanoop1@paanoop1-desktop.(none)>
>
> This patch add bus glue for USB controller commonly found in PMC-Sierra MSP71xx family of SoC's.
>
>
> Signed-off-by: Anoop P A <anoop.pa@xxxxxxxxx>
> ---
> Changes.
> ehci-pmcmsp.c is based on latest ehci-pci.c.Addressed some stylistic issue pointed by Greg.
> Addressed comments from Matthieu CASTET.
Could you spell that out more completely next time?
> +config USB_EHCI_HCD_PMC_MSP
> + tristate "EHCI support for on-chip PMC MSP USB controller"
Better to say "EHCI support for on-chip PMC-Sierra MSP71xx USB controllers"
> + depends on USB_EHCI_HCD && MSP_HAS_USB
> + default y
New features always default to No.
> +#include <msp_usb.h>
Cannot find the msp_usb.h in linux-next. Doesn't compile.
> +static void usb_hcd_tdi_set_mode(struct ehci_hcd *ehci)
> +{
> + u8 *base;
> + u8 *statreg;
> + u8 *fiforeg;
> + u32 val;
> + struct ehci_regs *reg_base = ehci->regs;
> +
> + /* get register base */
> + base = (u8 *)reg_base + USB_EHCI_REG_USB_MODE;
> + statreg = (u8 *)reg_base + USB_EHCI_REG_USB_STATUS;
> + fiforeg = (u8 *)reg_base + USB_EHCI_REG_USB_FIFO;
> +
> + /* Disable controller mode stream */
> + val = ehci_readl(ehci, (u32 *)base);
It doesn't compile so I can't test this, but I think that this will
cause a sparse warning. "base" should have an __iomem tag. Please
run sparse on this driver.
> +/* called after powerup, by probe or system-pm "wakeup" */
> +static int ehci_msp_reinit(struct ehci_hcd *ehci)
> +{
> + ehci_port_power(ehci, 0);
> +
> + return 0;
Better to make this function void.
> +}
> +
> +/* called during probe() after chip reset completes */
> +static int ehci_msp_setup(struct usb_hcd *hcd)
> +{
> + struct ehci_hcd *ehci = hcd_to_ehci(hcd);
> + u32 temp;
> + int retval;
Needs a blank line here to separate declarations from code.
> + ehci->big_endian_mmio = 1;
> + ehci->big_endian_desc = 1;
> +
> + ehci->caps = hcd->regs;
> + ehci->regs = hcd->regs +
> + HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
[snip]
> + /* data structure init */
> + retval = ehci_init(hcd);
> + if (retval)
> + return retval;
> +
> + temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
> + temp &= 0x0f;
companion HCs * ports per CC & 0xf?
What's the &= 0x0f for? It's left out of the printk.
> + if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
> + ehci_dbg(ehci, "bogus port configuration: "
> + "cc=%d x pcc=%d < ports=%d\n",
> + HCS_N_CC(ehci->hcs_params),
> + HCS_N_PCC(ehci->hcs_params),
> + HCS_N_PORTS(ehci->hcs_params));
> + }
[snip]
> +/*-------------------------------------------------------------------------*/
No need for these blank comments.
> +
> +static void msp_start_hc(struct platform_device *dev)
> +{
> +}
> +
> +static void msp_stop_hc(struct platform_device *dev)
> +{
> +}
> +
I don't understand the point of these empty functions.
> +static int ehci_msp_suspend(struct device *dev)
> +{
> + struct usb_hcd *hcd = dev_get_drvdata(dev);
> + struct ehci_hcd *ehci = hcd_to_ehci(hcd);
> + unsigned long flags;
> + int rc;
> +
> + return 0;
> + rc = 0;
> +
> + if (time_before(jiffies, ehci->next_statechange))
> + usleep(10000);
Is there still a usleep() function? Either way, can you send us
something that compiles on linux-next?
regards,
dan carpenter
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
