Igor Grinberg <grinberg@xxxxxxxxxxxxxx> writes:
> On 01/03/11 13:41, Arnaud Patard (Rtp) wrote:
>> Igor Grinberg <grinberg@xxxxxxxxxxxxxx> writes:
>> Hi,
>>> On 12/23/10 22:11, Arnaud Patard (Rtp) wrote:
>>>> Igor Grinberg <grinberg@xxxxxxxxxxxxxx> writes:
>>>>> Hi Arnaud,
>>>>>
>>>>> On 12/20/10 17:48, Arnaud Patard (Rtp) wrote:
>>>>>> Current code doesn't handle setting CHRGVBUS when enabling vbus.
>>>>>> Add support for it
>>>>>>
>>>>>>
>>>>>>
>>>>>> Signed-off-by: Arnaud Patard <arnaud.patard@xxxxxxxxxxx>
>>>>>> Index: tst-usb/drivers/usb/otg/ulpi.c
>>>>>> ===================================================================
>>>>>> --- tst-usb.orig/drivers/usb/otg/ulpi.c 2010-12-20 15:38:41.000000000 +0100
>>>>>> +++ tst-usb/drivers/usb/otg/ulpi.c 2010-12-20 15:38:57.000000000 +0100
>>>>>> @@ -234,7 +234,8 @@
>>>>>> {
>>>>>> unsigned int flags = otg_io_read(otg, ULPI_OTG_CTRL);
>>>>>>
>>>>>> - flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT);
>>>>>> + flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT |
>>>>>> + ULPI_OTG_CTRL_CHRGVBUS);
>>>>>>
>>>>>> if (on) {
>>>>>> if (otg->flags & ULPI_OTG_DRVVBUS)
>>>>>> @@ -242,6 +243,9 @@
>>>>>>
>>>>>> if (otg->flags & ULPI_OTG_DRVVBUS_EXT)
>>>>>> flags |= ULPI_OTG_CTRL_DRVVBUS_EXT;
>>>>>> +
>>>>>> + if (otg->flags & ULPI_OTG_CHRGVBUS)
>>>>>> + flags |= ULPI_OTG_CTRL_CHRGVBUS;
>>>>>> }
>>>>>>
>>>>>> return otg_io_write(otg, flags, ULPI_OTG_CTRL);
>>>>> I think this is a wrong place to set the ChrgVbus bit.
>>>>> As for ULPI spec. 1.1:
>>>>> "3.8.7.1 Session Request Protocol (SRP)
>>>>> ULPI provides full SRP support. The Link uses the ChrgVbus and DischrgVbus bits
>>>>> in the OTG Control register to begin and end a session."
>>>>>
>>>>> So it is used for SRP.
>>>>> May be it is better to implement
>>>>> int (*start_srp)(struct otg_transceiver *otg);
>>>>> method for setting this bit?
>>>>>
>>>> I was not sure on where to put this so I took the same approach as the
>>>> fsl bsp which was to set it in this function and to call this function
>>>> _after_ usb_add_hcd() [ see my previous patch ]. Indeed, it fixed my
>>>> issue so I believe it not so bad given that there has already been some
>>>> troubles on the ehci-mxc init.
>>> Well, the problem is that this is supposed to be a generic driver and it should
>>> somehow follow the ULPI spec.
>>> This patch makes it more like mxc specific.
>>>
>>> As far as I understand, Session Request Protocol (SRP) allows a B-device (Peripheral)
>>> to nudge an A-device (Host) to turn on the USB's Vbus.
>>> This patch enables SRP along with Vbus, which seems incorrect completely.
>>> ulpi_set_vbus() should set the Vbus (as its name says) and that's it.
>> so, if I add a srp hook as you're suggesting, which part of the driver
>> should call it ?
>
> It should be called from outside the ulpi driver by the OTG logic
> (just like ulpi_set_vbus() is called).
> But, again, SRP should be set by the B-device (peripheral) and Vbus by the A-device (Host).
> Usually, the A-device and B-device are on the opposite sides of the USB cable.
>
>>> Have you tried without this patch or have you just applied it along with other
>>> patches from the fsl bsp?
>> I already tried without this patch and without it, things are not
>> working on my systems.
>>> Also, if this specific patch (2/5) makes your USB (Host as I understand) work,
>>> it makes me think that there could be some problem with your Vbus supply.
>>> Have you checked that?
>> I don't have any schematics and I've access only to the source code of
>> the kernel running on the efika nettop and smartbook [1]. I've not seen
>> anything (even remotely) related to vbus supply except in the ulpi code
>> and from what I've heard, it's unlikely that there's something to
>> control it on theses systems. Of course, I'll be happy to be proven
>> wrong. Without usb theses systems are useless so anything the can reduce
>> the number of patches needed to get the systems working with mainline is
>> welcome.
>
> Well, I was certain you are trying to use that port in Host mode (A-device), but
> now I'm confused...
> You say "things are not working" - what are those things?
> Can you, please, describe what are you trying to do?
> What are you trying to connect to this USB port? What cable do you
> use?
I thought it was clear that "things" was everything connected on the usb
ports. The problem is that this also means that the nettop/smartbook are
kind of not working too as ethernet/wifi/bt/hid devs are all connected
on usb [ they're all on the pcb ]. So, even if you boot on the mmc aka
the only storage available which doesn't need usb, you won't be able to
login.
> Also, what ulpi vendor/product id is reported in ulpi_init()?
ULPI transceiver vendor/product ID 0x0424/0x0006
Found SMSC USB3319 ULPI transceiver.
Arnaud
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
