On 01/03/11 13:41, Arnaud Patard (Rtp) wrote:
> Igor Grinberg <grinberg@xxxxxxxxxxxxxx> writes:
> Hi,
>> On 12/23/10 22:11, Arnaud Patard (Rtp) wrote:
>>> Igor Grinberg <grinberg@xxxxxxxxxxxxxx> writes:
>>>> Hi Arnaud,
>>>>
>>>> On 12/20/10 17:48, Arnaud Patard (Rtp) wrote:
>>>>> Current code doesn't handle setting CHRGVBUS when enabling vbus.
>>>>> Add support for it
>>>>>
>>>>>
>>>>>
>>>>> Signed-off-by: Arnaud Patard <arnaud.patard@xxxxxxxxxxx>
>>>>> Index: tst-usb/drivers/usb/otg/ulpi.c
>>>>> ===================================================================
>>>>> --- tst-usb.orig/drivers/usb/otg/ulpi.c 2010-12-20 15:38:41.000000000 +0100
>>>>> +++ tst-usb/drivers/usb/otg/ulpi.c 2010-12-20 15:38:57.000000000 +0100
>>>>> @@ -234,7 +234,8 @@
>>>>> {
>>>>> unsigned int flags = otg_io_read(otg, ULPI_OTG_CTRL);
>>>>>
>>>>> - flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT);
>>>>> + flags &= ~(ULPI_OTG_CTRL_DRVVBUS | ULPI_OTG_CTRL_DRVVBUS_EXT |
>>>>> + ULPI_OTG_CTRL_CHRGVBUS);
>>>>>
>>>>> if (on) {
>>>>> if (otg->flags & ULPI_OTG_DRVVBUS)
>>>>> @@ -242,6 +243,9 @@
>>>>>
>>>>> if (otg->flags & ULPI_OTG_DRVVBUS_EXT)
>>>>> flags |= ULPI_OTG_CTRL_DRVVBUS_EXT;
>>>>> +
>>>>> + if (otg->flags & ULPI_OTG_CHRGVBUS)
>>>>> + flags |= ULPI_OTG_CTRL_CHRGVBUS;
>>>>> }
>>>>>
>>>>> return otg_io_write(otg, flags, ULPI_OTG_CTRL);
>>>> I think this is a wrong place to set the ChrgVbus bit.
>>>> As for ULPI spec. 1.1:
>>>> "3.8.7.1 Session Request Protocol (SRP)
>>>> ULPI provides full SRP support. The Link uses the ChrgVbus and DischrgVbus bits
>>>> in the OTG Control register to begin and end a session."
>>>>
>>>> So it is used for SRP.
>>>> May be it is better to implement
>>>> int (*start_srp)(struct otg_transceiver *otg);
>>>> method for setting this bit?
>>>>
>>> I was not sure on where to put this so I took the same approach as the
>>> fsl bsp which was to set it in this function and to call this function
>>> _after_ usb_add_hcd() [ see my previous patch ]. Indeed, it fixed my
>>> issue so I believe it not so bad given that there has already been some
>>> troubles on the ehci-mxc init.
>> Well, the problem is that this is supposed to be a generic driver and it should
>> somehow follow the ULPI spec.
>> This patch makes it more like mxc specific.
>>
>> As far as I understand, Session Request Protocol (SRP) allows a B-device (Peripheral)
>> to nudge an A-device (Host) to turn on the USB's Vbus.
>> This patch enables SRP along with Vbus, which seems incorrect completely.
>> ulpi_set_vbus() should set the Vbus (as its name says) and that's it.
> so, if I add a srp hook as you're suggesting, which part of the driver
> should call it ?
It should be called from outside the ulpi driver by the OTG logic
(just like ulpi_set_vbus() is called).
But, again, SRP should be set by the B-device (peripheral) and Vbus by the A-device (Host).
Usually, the A-device and B-device are on the opposite sides of the USB cable.
>> Have you tried without this patch or have you just applied it along with other
>> patches from the fsl bsp?
> I already tried without this patch and without it, things are not
> working on my systems.
>> Also, if this specific patch (2/5) makes your USB (Host as I understand) work,
>> it makes me think that there could be some problem with your Vbus supply.
>> Have you checked that?
> I don't have any schematics and I've access only to the source code of
> the kernel running on the efika nettop and smartbook [1]. I've not seen
> anything (even remotely) related to vbus supply except in the ulpi code
> and from what I've heard, it's unlikely that there's something to
> control it on theses systems. Of course, I'll be happy to be proven
> wrong. Without usb theses systems are useless so anything the can reduce
> the number of patches needed to get the systems working with mainline is
> welcome.
Well, I was certain you are trying to use that port in Host mode (A-device), but
now I'm confused...
You say "things are not working" - what are those things?
Can you, please, describe what are you trying to do?
What are you trying to connect to this USB port? What cable do you use?
Also, what ulpi vendor/product id is reported in ulpi_init()?
> Arnaud
>
> [1] http://gitorious.org/efikamx/linux-kernel/
--
Regards,
Igor.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
