Hi, everyone. first of all, it's not a regression (all kernels pre-2.6.36 not work either). I just tried to use an usb security key with 2.6.36. It failed with message: usbhid 2-2:1.0: couldn't find an input interrupt endpoint The same key can be used in Windows XP SP2 with no special driver, so I assume that Linux can use it. In XP, the key was identified as HID-compliant device dmesg/kernel config/lspci -v/lsusb -b detached. Any suggestions? Thanks.
Linux version 2.6.36 (fengxj@darkstar) (gcc version 4.5.1 (GCC) ) #1 SMP Sat Oct 23 19:31:15 CST 2010
Command line: BOOT_IMAGE=Linux-test ro root=803
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f6e0000 (usable)
BIOS-e820: 000000007f6e0000 - 000000007f6ef000 (ACPI data)
BIOS-e820: 000000007f6ef000 - 000000007f700000 (ACPI NVS)
BIOS-e820: 000000007f700000 - 0000000080000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
NX (Execute Disable) protection: active
DMI present.
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x7f6e0 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DBFFF uncachable
DC000-DFFFF write-back
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07F700000 mask FFFF00000 uncachable
2 base 07F800000 mask FFF800000 uncachable
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2039MB, range: 1MB, type UC
reg 2, base: 2040MB, range: 8MB, type UC
total RAM covered: 2039M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 16M num_reg: 3 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2039MB, range: 1MB, type UC
reg 2, base: 2040MB, range: 8MB, type UC
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-000000007f6e0000
0000000000 - 007f600000 page 2M
007f600000 - 007f6e0000 page 4k
kernel direct mapping tables up to 7f6e0000 @ 8000-c000
ACPI: RSDP 00000000000f6860 00024 (v02 LENOVO)
ACPI: XSDT 000000007f6e57d8 0008C (v01 LENOVO TP-7E 00002200 LTP 00000000)
ACPI: FACP 000000007f6e5900 000F4 (v03 LENOVO TP-7E 00002200 LNVO 00000001)
ACPI Warning: 32/64X length mismatch in Gpe1Block: 0/32 (20100702/tbfadt-526)
ACPI Warning: Optional field Gpe1Block has zero address or length: 0x000000000000102C/0x0 (20100702/tbfadt-557)
ACPI: DSDT 000000007f6e5c5e 08FB1 (v01 LENOVO TP-7E 00002200 MSFT 0100000E)
ACPI: FACS 000000007f6f4000 00040
ACPI: SSDT 000000007f6e5ab4 001AA (v01 LENOVO TP-7E 00002200 MSFT 0100000E)
ACPI: ECDT 000000007f6eec0f 00052 (v01 LENOVO TP-7E 00002200 LNVO 00000001)
ACPI: TCPA 000000007f6eec61 00032 (v02 LENOVO TP-7E 00002200 LNVO 00000001)
ACPI: APIC 000000007f6eec93 00068 (v01 LENOVO TP-7E 00002200 LNVO 00000001)
ACPI: MCFG 000000007f6eecfb 0003C (v01 LENOVO TP-7E 00002200 LNVO 00000001)
ACPI: HPET 000000007f6eed37 00038 (v01 LENOVO TP-7E 00002200 LNVO 00000001)
ACPI: SLIC 000000007f6eee62 00176 (v01 LENOVO TP-7E 00002200 LTP 00000000)
ACPI: BOOT 000000007f6eefd8 00028 (v01 LENOVO TP-7E 00002200 LTP 00000001)
ACPI: SSDT 000000007f6f2613 0025F (v01 LENOVO TP-7E 00002200 INTL 20050513)
ACPI: SSDT 000000007f6f2872 000A6 (v01 LENOVO TP-7E 00002200 INTL 20050513)
ACPI: SSDT 000000007f6f2918 004F7 (v01 LENOVO TP-7E 00002200 INTL 20050513)
ACPI: SSDT 000000007f6f2e0f 001D8 (v01 LENOVO TP-7E 00002200 INTL 20050513)
ACPI: Local APIC address 0xfee00000
[ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880001e00000-ffff8800039fffff] on node 0
Zone PFN ranges:
DMA 0x00000001 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal empty
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000001 -> 0x0000009f
0: 0x00000100 -> 0x0007f6e0
On node 0 totalpages: 521854
DMA zone: 56 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3942 pages, LIFO batch:0
DMA32 zone: 7081 pages used for memmap
DMA32 zone: 510775 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 40
early_res array is doubled to 64 at [7000 - 77ff]
Allocating PCI resources starting at 80000000 (gap: 80000000:70000000)
setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 24 pages/cpu @ffff880001600000 s77504 r0 d20800 u1048576
pcpu-alloc: s77504 r0 d20800 u1048576 alloc=1*2097152
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514717
Kernel command line: BOOT_IMAGE=Linux-test ro root=803
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
No AGP bridge found
Subtract (46 early reservations)
#1 [0001000000 - 00015e69b4] TEXT DATA BSS
#2 [000009f000 - 0000100000] BIOS reserved
#3 [00015e7000 - 00015e7150] BRK
#4 [0000001000 - 0000003000] TRAMPOLINE
#5 [0000003000 - 0000007000] ACPI WAKEUP
#6 [0000008000 - 000000a000] PGTABLE
#7 [00015e7180 - 00015e8180] BOOTMEM
#8 [00015e69c0 - 00015e6ac0] BOOTMEM
#9 [0001de9000 - 0001dea000] BOOTMEM
#10 [0001dea000 - 0001deb000] BOOTMEM
#11 [0001e00000 - 0003a00000] MEMMAP 0
#12 [00015e6ac0 - 00015e6c40] BOOTMEM
#13 [00015e8180 - 00015f4180] BOOTMEM
#14 [00015f5000 - 00015f6000] BOOTMEM
#15 [00015e6c40 - 00015e6c81] BOOTMEM
#16 [00015e6cc0 - 00015e6d03] BOOTMEM
#17 [00015f4180 - 00015f4500] BOOTMEM
#18 [00015e6d40 - 00015e6da8] BOOTMEM
#19 [00015e6dc0 - 00015e6e28] BOOTMEM
#20 [00015e6e40 - 00015e6ea8] BOOTMEM
#21 [00015e6ec0 - 00015e6f28] BOOTMEM
#22 [00015e6f40 - 00015e6fa8] BOOTMEM
#23 [00015f4500 - 00015f4568] BOOTMEM
#24 [00015f4580 - 00015f45e8] BOOTMEM
#25 [00015f4600 - 00015f4668] BOOTMEM
#26 [00015f4680 - 00015f46e8] BOOTMEM
#27 [00015f4700 - 00015f4768] BOOTMEM
#28 [00015f4780 - 00015f47e8] BOOTMEM
#29 [00015f4800 - 00015f4868] BOOTMEM
#30 [00015f4880 - 00015f48e8] BOOTMEM
#31 [00015f4900 - 00015f4968] BOOTMEM
#32 [00015f4980 - 00015f49e8] BOOTMEM
#33 [00015e6fc0 - 00015e6fe2] BOOTMEM
#34 [00015f4a00 - 00015f4a22] BOOTMEM
#35 [0001600000 - 0001618000] BOOTMEM
#36 [0001700000 - 0001718000] BOOTMEM
#37 [00015f4a40 - 00015f4a48] BOOTMEM
#38 [00015f4a80 - 00015f4a88] BOOTMEM
#39 [00015f4ac0 - 00015f4ac8] BOOTMEM
#40 [00015f4b00 - 00015f4b10] BOOTMEM
#41 [00015f4b40 - 00015f4c80] BOOTMEM
#42 [00015f4c80 - 00015f4ce0] BOOTMEM
#43 [00015f6000 - 00015fe000] BOOTMEM
#44 [0001718000 - 0001918000] BOOTMEM
#45 [0001918000 - 0001a18000] BOOTMEM
Memory: 2049304k/2087808k available (3628k kernel code, 392k absent, 38112k reserved, 1755k data, 392k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:320
Extended CMOS year: 2000
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 1330.008 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 2660.01 BogoMIPS (lpj=13300080)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 256
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Events: PEBS fmt0-, Core2 events, Intel PMU driver.
PEBS disabled due to CPU errata.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
ACPI: Core revision 20100702
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 CPU L7200 @ 1.33GHz stepping 06
Booting Node 0, Processors #1 Ok.
TSC synchronization [CPU#0 -> CPU#1]:
Measured 411712 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
Brought up 2 CPUs
Total of 2 processors activated (5320.04 BogoMIPS).
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: EC description table is found, configuring boot EC
ACPI: SSDT 000000007f6f1d36 001FE (v01 PmRef Cpu0Ist 00000100 INTL 20050513)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 001FE (v01 PmRef Cpu0Ist 00000100 INTL 20050513)
ACPI: SSDT 000000007f6f1fb9 0065A (v01 PmRef Cpu0Cst 00000100 INTL 20050513)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 0065A (v01 PmRef Cpu0Cst 00000100 INTL 20050513)
ACPI: SSDT 000000007f6f1c6e 000C8 (v01 PmRef Cpu1Ist 00000100 INTL 20050513)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 000C8 (v01 PmRef Cpu1Ist 00000100 INTL 20050513)
ACPI: SSDT 000000007f6f1f34 00085 (v01 PmRef Cpu1Cst 00000100 INTL 20050513)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00000100 INTL 20050513)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: Power Resource [PUBS] (on)
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
pci 0000:00:02.0: reg 10: [mem 0xee100000-0xee17ffff]
pci 0000:00:02.0: reg 14: [io 0x1800-0x1807]
pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff pref]
pci 0000:00:02.0: reg 1c: [mem 0xee200000-0xee23ffff]
pci 0000:00:02.1: reg 10: [mem 0xee180000-0xee1fffff]
pci 0000:00:1b.0: reg 10: [mem 0xee240000-0xee243fff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1d.0: reg 20: [io 0x1820-0x183f]
pci 0000:00:1d.1: reg 20: [io 0x1840-0x185f]
pci 0000:00:1d.2: reg 20: [io 0x1860-0x187f]
pci 0000:00:1d.3: reg 20: [io 0x1880-0x189f]
pci 0000:00:1d.7: reg 10: [mem 0xee444000-0xee4443ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 1600 (mask 007f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 15e0 (mask 000f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 1680 (mask 001f)
pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 20: [io 0x1810-0x181f]
pci 0000:00:1f.2: reg 10: [io 0x18d0-0x18d7]
pci 0000:00:1f.2: reg 14: [io 0x18c4-0x18c7]
pci 0000:00:1f.2: reg 18: [io 0x18c8-0x18cf]
pci 0000:00:1f.2: reg 1c: [io 0x18c0-0x18c3]
pci 0000:00:1f.2: reg 20: [io 0x18b0-0x18bf]
pci 0000:00:1f.2: reg 24: [mem 0xee444400-0xee4447ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20: [io 0x18e0-0x18ff]
pci 0000:02:00.0: reg 10: [mem 0xee000000-0xee00ffff 64bit]
pci 0000:02:00.0: PME# supported from D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xee000000-0xee0fffff]
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:00.0: reg 10: [mem 0xedf00000-0xedf0ffff 64bit]
pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.1: PCI bridge to [bus 03-03]
pci 0000:00:1c.1: bridge window [io 0x2000-0x3fff]
pci 0000:00:1c.1: bridge window [mem 0xec000000-0xedffffff]
pci 0000:00:1c.1: bridge window [mem 0xe4000000-0xe40fffff 64bit pref]
pci 0000:00:1c.2: PCI bridge to [bus 04-0b]
pci 0000:00:1c.2: bridge window [io 0x4000-0x5fff]
pci 0000:00:1c.2: bridge window [mem 0xe8000000-0xe9ffffff]
pci 0000:00:1c.2: bridge window [mem 0xe4100000-0xe41fffff 64bit pref]
pci 0000:00:1c.3: PCI bridge to [bus 0c-13]
pci 0000:00:1c.3: bridge window [io 0x6000-0x7fff]
pci 0000:00:1c.3: bridge window [mem 0xea000000-0xebffffff]
pci 0000:00:1c.3: bridge window [mem 0xe4200000-0xe42fffff 64bit pref]
pci 0000:15:00.0: reg 10: [mem 0xe4300000-0xe4300fff]
pci 0000:15:00.0: supports D1 D2
pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 15-18] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x8000-0xbfff]
pci 0000:00:1e.0: bridge window [mem 0xe4300000-0xe7ffffff]
pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref]
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009f000 - 000000000009ffff
reserve RAM buffer: 000000007f6e0000 - 000000007fffffff
cfg80211: Calling CRDA to update world regulatory domain
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource hpet
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x000c0000-0x000c3fff] has been reserved
system 00:00: [mem 0x000c4000-0x000c7fff] has been reserved
system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved
system 00:00: [mem 0x000cc000-0x000cffff] has been reserved
system 00:00: [mem 0x000d0000-0x000d3fff] could not be reserved
system 00:00: [mem 0x000dc000-0x000dffff] could not be reserved
system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
system 00:00: [mem 0x00100000-0x7fffffff] could not be reserved
system 00:00: [mem 0xfec00000-0xffffffff] could not be reserved
system 00:02: [io 0x164e-0x164f] has been reserved
system 00:02: [io 0x1000-0x107f] has been reserved
system 00:02: [io 0x1180-0x11bf] has been reserved
system 00:02: [io 0x0800-0x080f] has been reserved
system 00:02: [io 0x15e0-0x15ef] has been reserved
system 00:02: [io 0x1600-0x165f] could not be reserved
system 00:02: [mem 0xf0000000-0xf3ffffff] has been reserved
system 00:02: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:02: [mem 0xfed14000-0xfed17fff] has been reserved
system 00:02: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:02: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:02: [mem 0xfed40000-0xfed40fff] has been reserved
pci 0000:00:1c.0: BAR 9: assigned [mem 0x80000000-0x801fffff 64bit pref]
pci 0000:00:1c.0: BAR 7: assigned [io 0xc000-0xcfff]
pci 0000:00:1c.0: PCI bridge to [bus 02-02]
pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:1c.0: bridge window [mem 0xee000000-0xee0fffff]
pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff 64bit pref]
pci 0000:00:1c.1: PCI bridge to [bus 03-03]
pci 0000:00:1c.1: bridge window [io 0x2000-0x3fff]
pci 0000:00:1c.1: bridge window [mem 0xec000000-0xedffffff]
pci 0000:00:1c.1: bridge window [mem 0xe4000000-0xe40fffff 64bit pref]
pci 0000:00:1c.2: PCI bridge to [bus 04-0b]
pci 0000:00:1c.2: bridge window [io 0x4000-0x5fff]
pci 0000:00:1c.2: bridge window [mem 0xe8000000-0xe9ffffff]
pci 0000:00:1c.2: bridge window [mem 0xe4100000-0xe41fffff 64bit pref]
pci 0000:00:1c.3: PCI bridge to [bus 0c-13]
pci 0000:00:1c.3: bridge window [io 0x6000-0x7fff]
pci 0000:00:1c.3: bridge window [mem 0xea000000-0xebffffff]
pci 0000:00:1c.3: bridge window [mem 0xe4200000-0xe42fffff 64bit pref]
pci 0000:15:00.0: BAR 9: assigned [mem 0xe0000000-0xe3ffffff pref]
pci 0000:15:00.0: BAR 10: assigned [mem 0x84000000-0x87ffffff]
pci 0000:15:00.0: BAR 7: assigned [io 0x8000-0x80ff]
pci 0000:15:00.0: BAR 8: assigned [io 0x8400-0x84ff]
pci 0000:15:00.0: CardBus bridge to [bus 16-17]
pci 0000:15:00.0: bridge window [io 0x8000-0x80ff]
pci 0000:15:00.0: bridge window [io 0x8400-0x84ff]
pci 0000:15:00.0: bridge window [mem 0xe0000000-0xe3ffffff pref]
pci 0000:15:00.0: bridge window [mem 0x84000000-0x87ffffff]
pci 0000:00:1e.0: PCI bridge to [bus 15-18]
pci 0000:00:1e.0: bridge window [io 0x8000-0xbfff]
pci 0000:00:1e.0: bridge window [mem 0xe4300000-0xe7ffffff]
pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref]
pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: enabling device (0005 -> 0007)
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:00: resource 8 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:00: resource 9 [mem 0x80000000-0xfebfffff]
pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:02: resource 1 [mem 0xee000000-0xee0fffff]
pci_bus 0000:02: resource 2 [mem 0x80000000-0x801fffff 64bit pref]
pci_bus 0000:03: resource 0 [io 0x2000-0x3fff]
pci_bus 0000:03: resource 1 [mem 0xec000000-0xedffffff]
pci_bus 0000:03: resource 2 [mem 0xe4000000-0xe40fffff 64bit pref]
pci_bus 0000:04: resource 0 [io 0x4000-0x5fff]
pci_bus 0000:04: resource 1 [mem 0xe8000000-0xe9ffffff]
pci_bus 0000:04: resource 2 [mem 0xe4100000-0xe41fffff 64bit pref]
pci_bus 0000:0c: resource 0 [io 0x6000-0x7fff]
pci_bus 0000:0c: resource 1 [mem 0xea000000-0xebffffff]
pci_bus 0000:0c: resource 2 [mem 0xe4200000-0xe42fffff 64bit pref]
pci_bus 0000:15: resource 0 [io 0x8000-0xbfff]
pci_bus 0000:15: resource 1 [mem 0xe4300000-0xe7ffffff]
pci_bus 0000:15: resource 2 [mem 0xe0000000-0xe3ffffff 64bit pref]
pci_bus 0000:15: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:15: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:15: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:15: resource 7 [mem 0x000d4000-0x000d7fff]
pci_bus 0000:15: resource 8 [mem 0x000d8000-0x000dbfff]
pci_bus 0000:15: resource 9 [mem 0x80000000-0xfebfffff]
pci_bus 0000:16: resource 0 [io 0x8000-0x80ff]
pci_bus 0000:16: resource 1 [io 0x8400-0x84ff]
pci_bus 0000:16: resource 2 [mem 0xe0000000-0xe3ffffff pref]
pci_bus 0000:16: resource 3 [mem 0x84000000-0x87ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
UDP hash table entries: 1024 (order: 3, 32768 bytes)
UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x2000
pci 0000:00:1d.0: Performing full reset
pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x2000
pci 0000:00:1d.1: Performing full reset
pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x2000
pci 0000:00:1d.2: Performing full reset
pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x2000
pci 0000:00:1d.3: Performing full reset
PCI: CLS mismatch (64 != 32), using 64 bytes
Simple Boot Flag at 0x35 set to 0x1
fuse init (API version 7.15)
msgmni has been set to 4002
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: ACPI _OSC control granted for 0x1d
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
pcieport 0000:00:1c.1: ACPI _OSC control granted for 0x1d
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
pcieport 0000:00:1c.2: ACPI _OSC control granted for 0x1d
pcieport 0000:00:1c.2: setting latency timer to 64
pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
pcieport 0000:00:1c.3: ACPI _OSC control granted for 0x1d
pcieport 0000:00:1c.3: setting latency timer to 64
pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
ACPI: AC Adapter [AC] (on-line)
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
acpi device:01: registered as cooling_device0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: acpi_idle registered with cpuidle
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (50 C)
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [THM1] (50 C)
Generic RTC Driver v1.07
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 945GM Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: power state changed by ACPI to D0
i915 0000:00:02.0: power state changed by ACPI to D0
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
ACPI: Battery Slot [BAT0] (battery present)
[drm] set up 7M of stolen space
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm] initialized overlay support
Console: switching to colour frame buffer device 128x48
fb0: inteldrmfb frame buffer device
drm: registered panic notifier
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xee444400 port 0xee444500 irq 44
ata2: DUMMY
ata3: DUMMY
ata4: DUMMY
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
ata6: port disabled. ignoring.
tg3.c:v3.113 (August 2, 2010)
tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
tg3 0000:02:00.0: setting latency timer to 64
tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM95751m) rev 4201] (PCI Express) MAC address 00:16:d3:bc:4a:bd
tg3 0000:02:00.0: eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
ath5k 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ath5k 0000:03:00.0: setting latency timer to 64
ath5k 0000:03:00.0: registered as 'phy0'
ata5.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-T10N, 1.04, max UDMA/33
ata5.00: configured for UDMA/33
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (unknown) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (unknown) filtered out
ata1.00: ACPI cmd ef/5f:00:00:00:00:a0 (unknown) succeeded
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (unknown) filtered out
ata1.00: ATA-8: FUJITSU MHY2160BH, 0000000B, max UDMA/100
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 (unknown) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (unknown) filtered out
ata1.00: ACPI cmd ef/5f:00:00:00:00:a0 (unknown) succeeded
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (unknown) filtered out
ata1.00: configured for UDMA/100
ata1.00: configured for UDMA/100
ata1: EH complete
scsi 0:0:0:0: Direct-Access ATA FUJITSU MHY2160B 0000 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 >
ath: EEPROM regdomain: 0x62
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x62
phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: ath5k-phy0::rx
sd 0:0:0:0: [sda] Attached SCSI disk
Registered led device: ath5k-phy0::tx
ath5k phy0: Atheros AR5414 chip found (MAC: 0xa3, PHY: 0x61)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
scsi 4:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-T10N 1.04 PQ: 0 ANSI: 5
ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: using broken periodic workaround
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: reset command 0080022 (park)=0 ithresh=8 Async period=1024 Reset HALT
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xee444000
ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.36 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.0: Performing full reset
uhci_hcd 0000:00:1d.0: supports USB remote wakeup
uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001820
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.36 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.1: Performing full reset
uhci_hcd 0000:00:1d.1: supports USB remote wakeup
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001840
usb usb3: default language 0x0409
usb usb3: udev 1, busnum 3, minor = 256
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.36 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1
uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.2: Performing full reset
uhci_hcd 0000:00:1d.2: supports USB remote wakeup
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
usb usb4: default language 0x0409
usb usb4: udev 1, busnum 4, minor = 384
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.36 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: usb_probe_device
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports
uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.3: Performing full reset
uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001880
usb usb5: default language 0x0409
usb usb5: udev 1, busnum 5, minor = 512
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.36 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
usb usb5: usb_probe_device
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
hub 5-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.3
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
usbhid: USB HID core driver
HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
hda_intel: probe_mask set to 0x1 for device 17aa:2010
HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
ALSA device list:
#0: HDA Intel at 0xee240000 irq 45
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input5
VFS: Mounted root (ext2 filesystem) readonly on device 8:3.
Freeing unused kernel memory: 392k freed
usb usb2: suspend_rh (auto-stop)
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
udevd (794): /proc/794/oom_adj is deprecated, please use /proc/794/oom_score_adj instead.
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
usb usb2: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Adding 2000088k swap on /dev/sda2. Priority:-1 extents:1 across:2000088k
device tap0 entered promiscuous mode
device tap1 entered promiscuous mode
tg3 0000:02:00.0: irq 46 for MSI/MSI-X
tg3 0000:02:00.0: BAR 0: set to [mem 0xee000000-0xee00ffff 64bit] (PCI address [0xee000000-0xee00ffff]
tg3 0000:02:00.0: irq 46 for MSI/MSI-X
wlan0: authenticate with 00:b0:0c:00:21:c0 (try 1)
wlan0: authenticated
wlan0: associate with 00:b0:0c:00:21:c0 (try 1)
wlan0: RX AssocResp from 00:b0:0c:00:21:c0 (capab=0x11 status=0 aid=1)
wlan0: associated
cfg80211: Calling CRDA for country: CN
CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
wlan0: deauthenticated from 00:b0:0c:00:21:c0 (Reason: 3)
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
tg3 0000:02:00.0: BAR 0: set to [mem 0xee000000-0xee00ffff 64bit] (PCI address [0xee000000-0xee00ffff]
tg3 0000:02:00.0: irq 46 for MSI/MSI-X
tg3 0000:02:00.0: BAR 0: set to [mem 0xee000000-0xee00ffff 64bit] (PCI address [0xee000000-0xee00ffff]
tg3 0000:02:00.0: irq 46 for MSI/MSI-X
wlan0: authenticate with 00:b0:0c:00:21:c0 (try 1)
wlan0: authenticated
wlan0: associate with 00:b0:0c:00:21:c0 (try 1)
wlan0: RX AssocResp from 00:b0:0c:00:21:c0 (capab=0x11 status=0 aid=1)
wlan0: associated
cfg80211: Calling CRDA for country: CN
usb usb1: usb wakeup-resume
usb usb1: usb auto-resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 1-0:1.0: hub_resume
ehci_hcd 0000:00:1d.7: GetStatus port:2 status 001803 0 ACK POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0004 evt 0000
hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.7: port 2 full speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port:2 status 003801 0 ACK POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
usb usb2: usb wakeup-resume
usb usb2: usb auto-resume
usb usb2: wakeup_rh
hub 2-0:1.0: hub_resume
uhci_hcd 0000:00:1d.0: port 2 portsc 0093,00
hub 2-0:1.0: port 2: status 0101 change 0001
ehci_hcd 0000:00:1d.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0004
hub 2-0:1.0: state 7 ports 2 chg 0004 evt 0000
hub 2-0:1.0: port 2, status 0101, change 0000, 12 Mb/s
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 2-2: ep0 maxpacket = 8
usb 2-2: config 1 descriptor has 1 excess byte, ignoring
usb 2-2: skipped 1 descriptor after interface
usb 2-2: default language 0x0409
usb 2-2: udev 2, busnum 2, minor = 129
usb 2-2: New USB device found, idVendor=1483, idProduct=c007
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: eKey
usb 2-2: Manufacturer: MingwahAohan
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usbhid 2-2:1.0: usb_probe_interface
usbhid 2-2:1.0: usb_probe_interface - got id
usbhid 2-2:1.0: couldn't find an input interrupt endpoint
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
CE: hpet increased min_delta_ns to 7500 nsec
usb usb1: usb auto-resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 1-0:1.0: hub_resume
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
usb usb3: usb auto-resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb4: usb auto-resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb auto-resume
usb usb5: wakeup_rh
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: hub_resume
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
usb usb3: usb auto-resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb4: usb auto-resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb5: usb auto-resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Attachment:
2.6.36.config
Description: Binary data
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at ee100000 (32-bit, non-prefetchable) [size=512K] I/O ports at 1800 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at ee200000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [d0] Power Management version 2 Kernel driver in use: i915 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: Lenovo ThinkPad T60/R60 series Flags: fast devsel Memory at ee180000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at ee240000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: ee000000-ee0fffff Prefetchable memory behind bridge: 0000000080000000-00000000801fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Lenovo Device 2011 Capabilities: [a0] Power Management version 2 Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00002000-00003fff Memory behind bridge: ec000000-edffffff Prefetchable memory behind bridge: 00000000e4000000-00000000e40fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Lenovo Device 2011 Capabilities: [a0] Power Management version 2 Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=0b, sec-latency=0 I/O behind bridge: 00004000-00005fff Memory behind bridge: e8000000-e9ffffff Prefetchable memory behind bridge: 00000000e4100000-00000000e41fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Lenovo Device 2011 Capabilities: [a0] Power Management version 2 Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=0c, subordinate=13, sec-latency=0 I/O behind bridge: 00006000-00007fff Memory behind bridge: ea000000-ebffffff Prefetchable memory behind bridge: 00000000e4200000-00000000e42fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Lenovo Device 2011 Capabilities: [a0] Power Management version 2 Capabilities: [100] Virtual Channel <?> Capabilities: [180] Root Complex Link <?> Kernel driver in use: pcieport 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at 1820 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at 1840 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at 1860 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at 1880 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0, IRQ 19 Memory at ee444000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=15, subordinate=18, sec-latency=32 I/O behind bridge: 00008000-0000bfff Memory behind bridge: e4300000-e7ffffff Prefetchable memory behind bridge: 00000000e0000000-00000000e3ffffff Capabilities: [50] Subsystem: Lenovo Device 2013 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at 1810 [size=16] Kernel driver in use: ata_piix 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 44 I/O ports at 18d0 [size=8] I/O ports at 18c4 [size=4] I/O ports at 18c8 [size=8] I/O ports at 18c0 [size=4] I/O ports at 18b0 [size=16] Memory at ee444400 (32-bit, non-prefetchable) [size=1K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 2 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) Subsystem: Lenovo ThinkPad T60/R60 series Flags: medium devsel, IRQ 23 I/O ports at 18e0 [size=32] Kernel driver in use: i801_smbus 02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751M Gigabit Ethernet PCI Express (rev 21) Subsystem: Lenovo ThinkPad R60e Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at ee000000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 2 Capabilities: [50] Vital Product Data Capabilities: [58] MSI: Enable+ Count=1/8 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-16-d3-ff-fe-bc-4a-bd Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 03:00.0 Ethernet controller: Atheros Communications Inc. AR5212 802.11abg NIC (rev 01) Subsystem: IBM ThinkPad 11a/b/g Wireless LAN Mini Express Adapter (AR5BXB6) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at edf00000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel <?> Kernel driver in use: ath5k 15:00.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller Subsystem: Lenovo ThinkPad T60/R60 series Flags: bus master, medium devsel, latency 168, IRQ 16 Memory at e4300000 (32-bit, non-prefetchable) [size=4K] Bus: primary=15, secondary=16, subordinate=17, sec-latency=176 Memory window 0: e0000000-e3fff000 (prefetchable) Memory window 1: 84000000-87fff000 (prefetchable) I/O window 0: 00008000-000080ff I/O window 1: 00008400-000084ff 16-bit legacy interface ports at 0001
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1d.7
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 8
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 002 Device 002: ID 1483:c007
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1483
idProduct 0xc007
bcdDevice 3.00
iManufacturer 1 MingwahAohan
iProduct 2 eKey
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 28
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 289
Report Descriptor: (length is 289)
Item(Global): Usage Page, data= [ 0xa8 0xff ] 65448
(null)
Item(Local ): Usage, data= [ 0x00 ] 0
(null)
Item(Main ): Collection, data= [ 0x01 ] 1
Application
Item(Global): Logical Minimum, data= [ 0x00 ] 0
Item(Global): Logical Maximum, data= [ 0xff 0x00 ] 255
Item(Global): Report Size, data= [ 0x08 ] 8
Item(Global): Report ID, data= [ 0x01 ] 1
Item(Global): Report Count, data= [ 0x07 ] 7
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x02 ] 2
Item(Global): Report Count, data= [ 0x0f ] 15
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x03 ] 3
Item(Global): Report Count, data= [ 0x17 ] 23
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x04 ] 4
Item(Global): Report Count, data= [ 0x1f ] 31
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x05 ] 5
Item(Global): Report Count, data= [ 0x27 ] 39
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x06 ] 6
Item(Global): Report Count, data= [ 0x2f ] 47
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x07 ] 7
Item(Global): Report Count, data= [ 0x37 ] 55
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x08 ] 8
Item(Global): Report Count, data= [ 0x3f ] 63
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x09 ] 9
Item(Global): Report Count, data= [ 0x47 ] 71
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x0a ] 10
Item(Global): Report Count, data= [ 0x4f ] 79
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x0b ] 11
Item(Global): Report Count, data= [ 0x57 ] 87
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x0c ] 12
Item(Global): Report Count, data= [ 0x5f ] 95
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x0d ] 13
Item(Global): Report Count, data= [ 0x67 ] 103
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x0e ] 14
Item(Global): Report Count, data= [ 0x6f ] 111
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x0f ] 15
Item(Global): Report Count, data= [ 0x77 ] 119
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x10 ] 16
Item(Global): Report Count, data= [ 0x7f ] 127
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x11 ] 17
Item(Global): Report Count, data= [ 0x87 ] 135
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x12 ] 18
Item(Global): Report Count, data= [ 0x8f ] 143
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x13 ] 19
Item(Global): Report Count, data= [ 0x97 ] 151
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x14 ] 20
Item(Global): Report Count, data= [ 0x9f ] 159
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x15 ] 21
Item(Global): Report Count, data= [ 0xa7 ] 167
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x16 ] 22
Item(Global): Report Count, data= [ 0xaf ] 175
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x17 ] 23
Item(Global): Report Count, data= [ 0xb7 ] 183
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x18 ] 24
Item(Global): Report Count, data= [ 0xbf ] 191
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x19 ] 25
Item(Global): Report Count, data= [ 0xc7 ] 199
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x1a ] 26
Item(Global): Report Count, data= [ 0xcf ] 207
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x1b ] 27
Item(Global): Report Count, data= [ 0xd7 ] 215
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x1c ] 28
Item(Global): Report Count, data= [ 0xdf ] 223
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x1d ] 29
Item(Global): Report Count, data= [ 0xe7 ] 231
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x1e ] 30
Item(Global): Report Count, data= [ 0xef ] 239
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x1f ] 31
Item(Global): Report Count, data= [ 0xf7 ] 247
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x20 ] 32
Item(Global): Report Count, data= [ 0xff ] 255
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x21 ] 33
Item(Global): Report Count, data= [ 0x07 0x01 ] 263
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Global): Report ID, data= [ 0x22 ] 34
Item(Global): Report Count, data= [ 0x0f 0x01 ] 271
Item(Local ): Usage, data= [ 0x01 ] 1
(null)
Item(Main ): Feature, data= [ 0x82 ] 130
Data Variable Absolute No_Wrap Linear
Preferred_State No_Null_Position Volatile Bitfield
Item(Main ): End Collection, data=none
Device Status: 0x0000
(Bus Powered)
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3 Linux 2.6.36 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
