This adds USB 2.0 support to ssb ohci driver.
This patch was used in OpenWRT for a long time now.
CC: Steve Brown <sbrown@xxxxxxxxxxxx>
Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
---
drivers/usb/host/ohci-ssb.c | 55 ++++++++++++++++++++++++++++++++++++++++--
1 files changed, 52 insertions(+), 3 deletions(-)
diff --git a/drivers/usb/host/ohci-ssb.c b/drivers/usb/host/ohci-ssb.c
index 23fd6a8..544f5b9 100644
--- a/drivers/usb/host/ohci-ssb.c
+++ b/drivers/usb/host/ohci-ssb.c
@@ -92,9 +92,12 @@ static const struct hc_driver ssb_ohci_hc_driver = {
static void ssb_ohci_detach(struct ssb_device *dev)
{
struct usb_hcd *hcd = ssb_get_drvdata(dev);
+ if (hcd->driver->shutdown)
+ hcd->driver->shutdown(hcd);
usb_remove_hcd(hcd);
iounmap(hcd->regs);
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
ssb_device_disable(dev, 0);
}
@@ -106,10 +109,55 @@ static int ssb_ohci_attach(struct ssb_device *dev)
int err = -ENOMEM;
u32 tmp, flags = 0;
- if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
- flags |= SSB_OHCI_TMSLOW_HOSTMODE;
+ if (dma_set_mask(dev->dma_dev, DMA_BIT_MASK(32)) ||
+ dma_set_coherent_mask(dev->dma_dev, DMA_BIT_MASK(32)))
+ return -EOPNOTSUPP;
- ssb_device_enable(dev, flags);
+ if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
+ /* Put the device into host-mode. */
+ flags |= SSB_OHCI_TMSLOW_HOSTMODE;
+ ssb_device_enable(dev, flags);
+ } else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
+ /*
+ * USB 2.0 special considerations:
+ *
+ * 1. Since the core supports both ehci and EHCI functions, it must
+ * only be reset once.
+ *
+ * 2. In addition to the standard SSB reset sequence, the Host Control
+ * Register must be programmed to bring the USB core and various
+ * phy components out of reset.
+ */
+ ssb_device_enable(dev, 0);
+ ssb_write32(dev, 0x200, 0x7ff);
+
+ /* Change Flush control reg */
+ tmp = ssb_read32(dev, 0x400);
+ tmp &= ~8;
+ ssb_write32(dev, 0x400, tmp);
+ tmp = ssb_read32(dev, 0x400);
+
+ /* Change Shim control reg */
+ tmp = ssb_read32(dev, 0x304);
+ tmp &= ~0x100;
+ ssb_write32(dev, 0x304, tmp);
+ tmp = ssb_read32(dev, 0x304);
+
+ udelay(1);
+
+ /* Work around for 5354 failures */
+ if ((dev->id.revision == 2) && (dev->bus->chip_id == 0x5354)) {
+ /* Change syn01 reg */
+ tmp = 0x00fe00fe;
+ ssb_write32(dev, 0x894, tmp);
+
+ /* Change syn03 reg */
+ tmp = ssb_read32(dev, 0x89c);
+ tmp |= 0x1;
+ ssb_write32(dev, 0x89c, tmp);
+ }
+ } else
+ ssb_device_enable(dev, 0);
hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
dev_name(dev->dev));
@@ -200,6 +248,7 @@ static int ssb_ohci_resume(struct ssb_device *dev)
static const struct ssb_device_id ssb_ohci_table[] = {
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
SSB_DEVTABLE_END
};
MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
