[PATCH 151/229] USB: isp1760: Soften DW3 X/transaction error bit handling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Anton Vorontsov <cbouatmailru@xxxxxxxxx>

There were some reports[1] of isp1760 USB driver malfunctioning
with high speed devices, noticed on Blackfin and PowerPC targets.
These reports indicated that the original Philips 'pehcd'[2]
driver worked fine.

We've noticed the same issue with an ARM RealView platform. This
happens under load (with only some mass storage devices, not all,
just as in another report[3]):

  error bit is set in DW3
  error bit is set in DW3
  error bit is set in DW3
  usb 1-1.2: device descriptor read/64, error -32

It appears that the 'pehcd' driver checks the X bit only if the
transaction is halted (H bit), otherwise the error is so far
insignificant.

The ISP176x chips were modeled after EHCI, and EHCI spec says
(thanks to Alan Stern for pointing out):

"Transaction errors cause the status field to be updated to reflect
 the type of error, but the transaction continues to be retried until
 the Active bit is set to 0.  When the error counter reaches 0, the
 Halt bit is set and the Active bit is cleared."

So, just as the original Philips driver, isp1760 must report the
error only if the transaction error and the halt bits are set.

[1] http://markmail.org/message/lx4qrlbrs2uhcnly
[2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494
    See pehci.c:pehci_hcd_update_error_status().
[3] http://blackfin.uclinux.org/gf/tracker/5148

Signed-off-by: Anton Vorontsov <avorontsov@xxxxxxxxxx>
Acked-by: Sebastian Andrzej Siewior <bigeasy@xxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxx>
---
 drivers/usb/host/isp1760-hcd.c |    7 +++----
 1 files changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/host/isp1760-hcd.c b/drivers/usb/host/isp1760-hcd.c
index 13f7d12..dbcafa2 100644
--- a/drivers/usb/host/isp1760-hcd.c
+++ b/drivers/usb/host/isp1760-hcd.c
@@ -713,12 +713,11 @@ static int check_error(struct ptd *ptd)
 	u32 dw3;
 
 	dw3 = le32_to_cpu(ptd->dw3);
-	if (dw3 & DW3_HALT_BIT)
+	if (dw3 & DW3_HALT_BIT) {
 		error = -EPIPE;
 
-	if (dw3 & DW3_ERROR_BIT) {
-		printk(KERN_ERR "error bit is set in DW3\n");
-		error = -EPIPE;
+		if (dw3 & DW3_ERROR_BIT)
+			pr_err("error bit is set in DW3\n");
 	}
 
 	if (dw3 & DW3_QTD_ACTIVE) {
-- 
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux