From: Heikki Krogerus <ext-heikki.krogerus@xxxxxxxxx> Definitions for registers defined by ULPI specification v1.1. Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@xxxxxxxxx> Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxx> --- include/linux/usb/ulpi.h | 140 ++++++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 140 insertions(+), 0 deletions(-) diff --git a/include/linux/usb/ulpi.h b/include/linux/usb/ulpi.h index 20675c6..2369d07 100644 --- a/include/linux/usb/ulpi.h +++ b/include/linux/usb/ulpi.h @@ -1,6 +1,146 @@ +/* + * ulpi.h -- ULPI defines and function prorotypes + * + * Copyright (C) 2010 Nokia Corporation + * + * This software is distributed under the terms of the GNU General + * Public License ("GPL") as published by the Free Software Foundation, + * version 2 of that License. + */ + #ifndef __LINUX_USB_ULPI_H #define __LINUX_USB_ULPI_H +/*-------------------------------------------------------------------------*/ + +/* + * Macros for Set and Clear + * See ULPI 1.1 specification to find the registers with Set and Clear offsets + */ +#define ULPI_SET(a) (a + 1) +#define ULPI_CLR(a) (a + 2) + +/*-------------------------------------------------------------------------*/ + +/* + * Register Map + */ +#define ULPI_VENDOR_ID_LOW 0x00 +#define ULPI_VENDOR_ID_HIGH 0x01 +#define ULPI_PRODUCT_ID_LOW 0x02 +#define ULPI_PRODUCT_ID_HIGH 0x03 +#define ULPI_FUNC_CTRL 0x04 +#define ULPI_IFC_CTRL 0x07 +#define ULPI_OTG_CTRL 0x0a +#define ULPI_USB_INT_EN_RISE 0x0d +#define ULPI_USB_INT_EN_FALL 0x10 +#define ULPI_USB_INT_STS 0x13 +#define ULPI_USB_INT_LATCH 0x14 +#define ULPI_DEBUG 0x15 +#define ULPI_SCRATCH 0x16 +/* Optional Carkit Registers */ +#define ULPI_CARCIT_CTRL 0x19 +#define ULPI_CARCIT_INT_DELAY 0x1c +#define ULPI_CARCIT_INT_EN 0x1d +#define ULPI_CARCIT_INT_STS 0x20 +#define ULPI_CARCIT_INT_LATCH 0x21 +#define ULPI_CARCIT_PLS_CTRL 0x22 +/* Other Optional Registers */ +#define ULPI_TX_POS_WIDTH 0x25 +#define ULPI_TX_NEG_WIDTH 0x26 +#define ULPI_POLARITY_RECOVERY 0x27 +/* Access Extended Register Set */ +#define ULPI_ACCESS_EXTENDED 0x2f +/* Vendor Specific */ +#define ULPI_VENDOR_SPECIFIC 0x30 +/* Extended Registers */ +#define ULPI_EXT_VENDOR_SPECIFIC 0x80 + +/*-------------------------------------------------------------------------*/ + +/* Function Control */ +#define ULPI_FUNC_CTRL_XCVRSEL (1 << 0) +#define ULPI_FUNC_CTRL_XCVRSEL_MASK (3 << 0) +#define ULPI_FUNC_CTRL_HIGH_SPEED (0 << 0) +#define ULPI_FUNC_CTRL_FULL_SPEED (1 << 0) +#define ULPI_FUNC_CTRL_LOW_SPEED (2 << 0) +#define ULPI_FUNC_CTRL_FS4LS (3 << 0) +#define ULPI_FUNC_CTRL_TERMSELECT (1 << 2) +#define ULPI_FUNC_CTRL_OPMODE (1 << 3) +#define ULPI_FUNC_CTRL_OPMODE_MASK (3 << 3) +#define ULPI_FUNC_CTRL_OPMODE_NORMAL (0 << 3) +#define ULPI_FUNC_CTRL_OPMODE_NONDRIVING (1 << 3) +#define ULPI_FUNC_CTRL_OPMODE_DISABLE_NRZI (2 << 3) +#define ULPI_FUNC_CTRL_OPMODE_NOSYNC_NOEOP (3 << 3) +#define ULPI_FUNC_CTRL_RESET (1 << 5) +#define ULPI_FUNC_CTRL_SUSPENDM (1 << 6) + +/* Interface Control */ +#define ULPI_IFC_CTRL_6_PIN_SERIAL_MODE (1 << 0) +#define ULPI_IFC_CTRL_3_PIN_SERIAL_MODE (1 << 1) +#define ULPI_IFC_CTRL_CARKITMODE (1 << 2) +#define ULPI_IFC_CTRL_CLOCKSUSPENDM (1 << 3) +#define ULPI_IFC_CTRL_AUTORESUME (1 << 4) +#define ULPI_IFC_CTRL_EXTERNAL_VBUS (1 << 5) +#define ULPI_IFC_CTRL_PASSTHRU (1 << 6) +#define ULPI_IFC_CTRL_PROTECT_IFC_DISABLE (1 << 7) + +/* OTG Control */ +#define ULPI_OTG_CTRL_ID_PULLUP (1 << 0) +#define ULPI_OTG_CTRL_DP_PULLDOWN (1 << 1) +#define ULPI_OTG_CTRL_DM_PULLDOWN (1 << 2) +#define ULPI_OTG_CTRL_DISCHRGVBUS (1 << 3) +#define ULPI_OTG_CTRL_CHRGVBUS (1 << 4) +#define ULPI_OTG_CTRL_DRVVBUS (1 << 5) +#define ULPI_OTG_CTRL_DRVVBUS_EXT (1 << 6) +#define ULPI_OTG_CTRL_EXTVBUSIND (1 << 7) + +/* USB Interrupt Enable Rising, + * USB Interrupt Enable Falling, + * USB Interrupt Status and + * USB Interrupt Latch + */ +#define ULPI_INT_HOST_DISCONNECT (1 << 0) +#define ULPI_INT_VBUS_VALID (1 << 1) +#define ULPI_INT_SESS_VALID (1 << 2) +#define ULPI_INT_SESS_END (1 << 3) +#define ULPI_INT_IDGRD (1 << 4) + +/* Debug */ +#define ULPI_DEBUG_LINESTATE0 (1 << 0) +#define ULPI_DEBUG_LINESTATE1 (1 << 1) + +/* Carkit Control */ +#define ULPI_CARKIT_CTRL_CARKITPWR (1 << 0) +#define ULPI_CARKIT_CTRL_IDGNDDRV (1 << 1) +#define ULPI_CARKIT_CTRL_TXDEN (1 << 2) +#define ULPI_CARKIT_CTRL_RXDEN (1 << 3) +#define ULPI_CARKIT_CTRL_SPKLEFTEN (1 << 4) +#define ULPI_CARKIT_CTRL_SPKRIGHTEN (1 << 5) +#define ULPI_CARKIT_CTRL_MICEN (1 << 6) + +/* Carkit Interrupt Enable */ +#define ULPI_CARKIT_INT_EN_IDFLOAT_RISE (1 << 0) +#define ULPI_CARKIT_INT_EN_IDFLOAT_FALL (1 << 1) +#define ULPI_CARKIT_INT_EN_CARINTDET (1 << 2) +#define ULPI_CARKIT_INT_EN_DP_RISE (1 << 3) +#define ULPI_CARKIT_INT_EN_DP_FALL (1 << 4) + +/* Carkit Interrupt Status and + * Carkit Interrupt Latch + */ +#define ULPI_CARKIT_INT_IDFLOAT (1 << 0) +#define ULPI_CARKIT_INT_CARINTDET (1 << 1) +#define ULPI_CARKIT_INT_DP (1 << 2) + +/* Carkit Pulse Control*/ +#define ULPI_CARKIT_PLS_CTRL_TXPLSEN (1 << 0) +#define ULPI_CARKIT_PLS_CTRL_RXPLSEN (1 << 1) +#define ULPI_CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2) +#define ULPI_CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3) + +/*-------------------------------------------------------------------------*/ + struct otg_transceiver *otg_ulpi_create(struct otg_io_access_ops *ops, unsigned int flags); -- 1.7.1 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html