From: Fabien Parent <fparent@xxxxxxxxxxxx>
Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding
configuration for TCPC Port, USB-C connector, and related settings.
Configure dual role switch capability, set up PD (Power Delivery) profiles,
and establish endpoints for SSUSB (SuperSpeed USB).
Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode
to "otg" for OTG (On-The-Go) mode operation.
Signed-off-by: Fabien Parent <fparent@xxxxxxxxxxxx>
Signed-off-by: Yow-Shin Liou <yow-shin.liou@xxxxxxxxxxxx>
Signed-off-by: Simon Sun <simon.sun@xxxxxxxxxxxxxxx>
Signed-off-by: Macpaul Lin <macpaul.lin@xxxxxxxxxxxx>
---
.../dts/mediatek/mt8395-genio-1200-evk.dts | 54 +++++++++++++++++++
1 file changed, 54 insertions(+)
Changes for v2:
- Drop the no need '1/2' DT Schema update patch in the 1st version.
- Fix intent for 'ports' node, it should under the 'connector' node.
- Correct the index for 'port@0' and 'port@1' node.
Changes for v3:
- Correct the order between new added nodes.
diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
index 5f16fb820580..83d520226302 100644
--- a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
@@ -335,6 +335,43 @@ mt6360_ldo7: ldo7 {
regulator-always-on;
};
};
+
+ tcpc {
+ compatible = "mediatek,mt6360-tcpc";
+ interrupts-extended = <&pio 17 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "PD_IRQB";
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 1000, \
+ PDO_FIXED_DUAL_ROLE | \
+ PDO_FIXED_DATA_SWAP)>;
+ sink-pdos = <PDO_FIXED(5000, 2000, \
+ PDO_FIXED_DUAL_ROLE | \
+ PDO_FIXED_DATA_SWAP)>;
+ op-sink-microwatt = <10000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ mt6360_ssusb_ep: endpoint {
+ remote-endpoint = <&ssusb_ep>;
+ };
+ };
+ };
+ };
+ };
};
};
@@ -770,6 +807,13 @@ pins-reset {
};
};
+ u3_p0_vbus: u3-p0-vbus-default-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>;
+ input-enable;
+ };
+ };
+
uart0_pins: uart0-pins {
pins {
pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
@@ -900,8 +944,18 @@ &ufsphy {
};
&ssusb0 {
+ dr_mode = "otg";
+ pinctrl-names = "default";
+ pinctrl-0 = <&u3_p0_vbus>;
+ usb-role-switch;
vusb33-supply = <&mt6359_vusb_ldo_reg>;
status = "okay";
+
+ port {
+ ssusb_ep: endpoint {
+ remote-endpoint = <&mt6360_ssusb_ep>;
+ };
+ };
};
&ssusb2 {
--
2.45.2
