Re: [PATCH v2 2/3] arm64: dts: imx8mp-evk: add typec node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Aug 01, 2024 at 02:51:06PM +0300, Dmitry Baryshkov wrote:
> On Thu, Aug 01, 2024 at 02:49:06PM GMT, Xu Yang wrote:
> > The first port of USB with type-C connector, which has dual data
> > role and dual power role.
> > 
> > Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
> > 
> > ---
> > Changes in v2:
> >  - modify endpoint label
> >  - fix usb phy tunning property dtbinding warning
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mp-evk.dts | 104 +++++++++++++++++++
> >  1 file changed, 104 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > index 938347704136..ef9b821a0ae2 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > @@ -6,6 +6,7 @@
> >  /dts-v1/;
> >  
> >  #include <dt-bindings/phy/phy-imx8-pcie.h>
> > +#include <dt-bindings/usb/pd.h>
> >  #include "imx8mp.dtsi"
> >  
> >  / {
> > @@ -26,6 +27,20 @@ backlight_lvds: backlight-lvds {
> >  		status = "disabled";
> >  	};
> >  
> > +	cbdtu02043: typec-mux {
> > +		compatible = "nxp,cbdtu02043", "gpio-sbu-mux";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_typec_mux>;
> > +		select-gpios =<&gpio4 20 GPIO_ACTIVE_HIGH>;
> > +		orientation-switch;
> > +
> > +		port {
> > +			usb3_data_ss: endpoint {
> > +				remote-endpoint = <&typec_con_ss>;
> 
> Where do SS lines go after the cbdtu02043?

I got your point. I should represent the signal route on dts even though
the driver doesn't use this information.

> Also could you please point out the datasheet for the chip.

https://www.nxp.com/docs/en/data-sheet/CBTU02043.pdf

> 
> > +			};
> > +		};
> > +	};
> > +
> >  	hdmi-connector {
> >  		compatible = "hdmi-connector";
> >  		label = "hdmi";
> > @@ -535,6 +550,49 @@ adv7535_out: endpoint {
> >  
> >  		};
> >  	};
> > +
> > +	ptn5110: tcpc@50 {
> > +		compatible = "nxp,ptn5110", "tcpci";
> > +		reg = <0x50>;
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_typec>;
> > +		interrupt-parent = <&gpio4>;
> > +		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> > +
> > +		usb_con: connector {
> > +			compatible = "usb-c-connector";
> > +			label = "USB-C";
> > +			power-role = "dual";
> > +			data-role = "dual";
> > +			try-power-role = "sink";
> > +			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> > +			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> > +				     PDO_VAR(5000, 20000, 3000)>;
> > +			op-sink-microwatt = <15000000>;
> > +			self-powered;
> > +
> > +			ports {
> > +				#address-cells = <1>;
> > +				#size-cells = <0>;
> > +
> > +				port@0 {
> > +					reg = <0>;
> > +
> > +					typec_con_hs: endpoint {
> > +						remote-endpoint = <&usb3_data_hs>;
> > +					};
> > +				};
> > +
> > +				port@1 {
> > +					reg = <1>;
> > +
> > +					typec_con_ss: endpoint {
> > +						remote-endpoint = <&usb3_data_ss>;
> > +					};
> > +				};
> 
> SBU lines are not connected?

Not use SBU signal.

Thanks,
Xu Yang

> 
> > +			};
> > +		};
> > +	};
> >  };
> >  
> >  &i2c3 {
> > @@ -704,7 +762,41 @@ &uart2 {
> >  	status = "okay";
> >  };
> >  
> 
> -- 
> With best wishes
> Dmitry




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux