On Sat, 25 May 2024 11:03:53 -0700, Bjorn Andersson wrote: > The USB multiport controller found in SC8180X is used to driver the > camera in the Lenovo Flex 5G, and a couple of additional USB ports on > the Primus AUX board. > > Signed-off-by: Bjorn Andersson <quic_bjorande@xxxxxxxxxxx> > --- > Bjorn Andersson (10): > dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add sc8180x USB3 compatible > phy: qcom-qmp-usb: Add sc8180x USB UNIPHY > dt-bindings: clock: qcom: Add missing USB MP resets > clk: qcom: gcc-sc8180x: Add missing USB MP resets > dt-bindings: usb: qcom,dwc3: Add SC8180X compatibles > arm64: dts: qcom: sc8180x-pmics: Add second PMC8180 GPIO > arm64: dts: qcom: sc8180x: Align USB nodes with binding > arm64: dts: qcom: sc8180x: Add USB MP controller and phys > arm64: dts: qcom: sc8180x-primus: Enable the two MP USB ports > arm64: dts: qcom: sc8180x-lenovo-flex-5g: Enable USB multiport controller > > .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 3 + > .../devicetree/bindings/usb/qcom,dwc3.yaml | 29 ++++ > .../arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dts | 32 ++++ > arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi | 16 +- > arch/arm64/boot/dts/qcom/sc8180x-primus.dts | 60 +++++++ > arch/arm64/boot/dts/qcom/sc8180x.dtsi | 175 +++++++++++++++++++-- > drivers/clk/qcom/gcc-sc8180x.c | 4 + > drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 3 + > include/dt-bindings/clock/qcom,gcc-sc8180x.h | 4 + > 9 files changed, 312 insertions(+), 14 deletions(-) > --- > base-commit: 3689b0ef08b70e4e03b82ebd37730a03a672853a > change-id: 20240524-sc8180x-usb-mp-4eb278df7ef1 > > Best regards, > -- > Bjorn Andersson <quic_bjorande@xxxxxxxxxxx> > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y qcom/sc8180x-lenovo-flex-5g.dtb qcom/sc8180x-primus.dtb' for 20240525-sc8180x-usb-mp-v1-0-60a904392438@xxxxxxxxxxx: arch/arm64/boot/dts/qcom/sc8180x-lenovo-flex-5g.dtb: clock-controller@af00000: clocks: [[41, 0], [42], [120, 0], [120, 1], [124, 0], [124, 1], [127, 0], [127, 1]] is too long from schema $id: http://devicetree.org/schemas/clock/qcom,dispcc-sm8x50.yaml# arch/arm64/boot/dts/qcom/sc8180x-primus.dtb: clock-controller@af00000: clocks: [[41, 0], [42], [122, 0], [122, 1], [126, 0], [126, 1], [129, 0], [129, 1]] is too long from schema $id: http://devicetree.org/schemas/clock/qcom,dispcc-sm8x50.yaml#
