Re: [REGRESSION][BISECTED] "xHCI host controller not responding, assume dead" on stable kernel > 6.8.7

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 5/22/2024 09:41, Gia wrote:
Now this is odd...

I've tested another cable - a very short one used with a Gen3 nvme
enclosure that I'm sure it's working - and I got Gen2 20 Gbps. I also
have tested this on Windows 11 and I still just got a Gen2 connection.

I was almost sure it was caused by a bad USB4 implementation by the PC
manufacturer, then I tried to connect a Thunderbolt 3 disk enclosure
via daisy chain to the Caldigit dock and I got the full Gen3 40 Gbps
connection! See the attached picture.


I suspect you can't actually get Gen 3 performance in this configuration. IIUC you should still be limited by the uplink to the host.

Those are some really odd findings but it's at least good it's "consistent" between Windows and Linux.

I'd suggest you report this to your manufacturer to investigate. Sanath can keep me honest I don't believe we've seen this problem on the reference stuff.

I'll try to connect the dock to a laptop via Thunderbolt 3 as a last
test and I'll report back.



On Tue, May 21, 2024 at 1:26 PM Mika Westerberg
<mika.westerberg@xxxxxxxxxxxxxxx> wrote:

On Tue, May 21, 2024 at 11:12:10AM +0200, Gia wrote:
Here you have the output from the dock upstream port:

sudo tbdump -r 2 -a 1 -vv -N2 LANE_ADP_CS_0

0x0036 0x003c013e 0b00000000 00111100 00000001 00111110 .... LANE_ADP_CS_0
   [00:07]       0x3e Next Capability Pointer
   [08:15]        0x1 Capability ID
   [16:19]        0xc Supported Link Speeds
   [20:21]        0x3 Supported Link Widths (SLW)
   [22:23]        0x0 Gen 4 Asymmetric Support (G4AS)
   [26:26]        0x0 CL0s Support
   [27:27]        0x0 CL1 Support
   [28:28]        0x0 CL2 Support
0x0037 0x0828003c 0b00001000 00101000 00000000 00111100 .... LANE_ADP_CS_1
   [00:03]        0xc Target Link Speed → Router shall attempt Gen 3 speed
   [04:05]        0x3 Target Link Width → Establish a Symmetric Link
   [06:07]        0x0 Target Asymmetric Link → Establish Symmetric Link
   [10:10]        0x0 CL0s Enable
   [11:11]        0x0 CL1 Enable
   [12:12]        0x0 CL2 Enable
   [14:14]        0x0 Lane Disable (LD)
   [15:15]        0x0 Lane Bonding (LB)
   [16:19]        0x8 Current Link Speed → Gen 2
   [20:25]        0x2 Negotiated Link Width → Symmetric Link (x2)
   [26:29]        0x2 Adapter State → CL0
   [30:30]        0x0 PM Secondary (PMS)

Hmm, okay both sides announce support of Gen3 yet the link is Gen2 which
makes me still suspect the cable, or the connection in general. I
suggest, if you have, try with another Thunderbolt cable.





[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux