Sharp's Spitz board still uses the legacy GPIO interface for controlling a GPIO pin related to the USB host controller. Convert this function to use the new GPIO descriptor interface. Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> Signed-off-by: Duje Mihanović <duje.mihanovic@xxxxxxxx> --- arch/arm/mach-pxa/spitz.c | 13 ++++++------- drivers/usb/host/ohci-pxa27x.c | 5 +++++ 2 files changed, 11 insertions(+), 7 deletions(-) diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index cc691b199429..535e2b2e997b 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {} * USB Host ******************************************************************************/ #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) +GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa", + SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW); + static int spitz_ohci_init(struct device *dev) { - int err; - - err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST"); - if (err) - return err; + gpiod_add_lookup_table(&spitz_usb_host_gpio_table); /* Only Port 2 is connected, setup USB Port 2 Output Control Register */ UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE; - return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1); + return 0; } static void spitz_ohci_exit(struct device *dev) { - gpio_free(SPITZ_GPIO_USB_HOST); + gpiod_remove_lookup_table(&spitz_usb_host_gpio_table); } static struct pxaohci_platform_data spitz_ohci_platform_data = { diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c index 357d9aee38a3..a809ba0bb25e 100644 --- a/drivers/usb/host/ohci-pxa27x.c +++ b/drivers/usb/host/ohci-pxa27x.c @@ -121,6 +121,7 @@ struct pxa27x_ohci { void __iomem *mmio_base; struct regulator *vbus[3]; bool vbus_enabled[3]; + struct gpio_desc *usb_host; }; #define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv) @@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev) pxa_ohci = to_pxa27x_ohci(hcd); pxa_ohci->clk = usb_clk; pxa_ohci->mmio_base = (void __iomem *)hcd->regs; + pxa_ohci->usb_host = devm_gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW); + if (IS_ERR(pxa_ohci->usb_host)) + return dev_err_probe(&pdev->dev, PTR_ERR(pxa_ohci->usb_host), + "failed to get USB host GPIO\n"); for (i = 0; i < 3; ++i) { char name[6]; -- 2.42.0