Hi all! I have to attach the MEGAWIN USB Bridge (vid=0x0e6a, pid=0x0101) to my Linux kernel. I followed the instructions in the kernel documentation and don´t know if either the driver finally doesn´t fit for the device or I have forgotten to configure something. Please have a look at the output: dmesg after calling "insmod usbserial vendor=0x0e6a product=0x0101" and plug- in of the device: [...] usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 hub 1-0:1.0: state 5 ports 2 chg 0000 evt 0004 brcm-ehci brcm-ehci.0: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501 brcm-ehci brcm-ehci.0: port 2 low speed --> companion brcm-ehci brcm-ehci.0: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC hub 1-0:1.0: port_wait_reset: err = -134 hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0004 brcm-ohci-0 brcm-ohci-0.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS hub 2-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 brcm-ohci-0 brcm-ohci-0.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS usb 2-2: new low speed USB device using brcm-ohci-0 and address 3 brcm-ohci-0 brcm-ohci-0.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS usb 2-2: default language 0x0409 usb 2-2: new device strings: Mfr=0, Product=2, SerialNumber=0 usb 2-2: Product: USB Bridge usb 2-2: hotplug usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: hotplug usbserial_generic 2-2:1.0: usb_probe_interface usbserial_generic 2-2:1.0: usb_probe_interface - got id usbserial_generic 2-2:1.0: Generic converter detected usbserial_generic 2-2:1.0: Generic device with no bulk out, not allowed. usbserial_generic: probe of 2-2:1.0 failed with error -5 hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0004 root@dm800:~# cat /proc/bus/usb/devices T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.12-5.1-brcmstb-dm800 ohci_hcd S: Product=BRCM OHCI S: SerialNumber=ohci-brcm C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.12-5.1-brcmstb-dm800 ohci_hcd S: Product=BRCM OHCI S: SerialNumber=ohci-brcm C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0e6a ProdID=0101 Rev= 5.10 S: Product=USB Bridge C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=03(Int.) MxPS= 8 Ivl=10ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.12-5.1-brcmstb-dm800 ehci_hcd S: Product=BRCM EHCI S: SerialNumber=ehci-brcm C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms Thanks in advance! Marian -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
