In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb3840 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@xxxxxxxxxxxxxxx>
Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
---
Changes in v2:
- no change
---
drivers/usb/chipidea/ci_hdrc_imx.c | 10 ++++++----
drivers/usb/chipidea/usbmisc_imx.c | 6 ++++--
2 files changed, 10 insertions(+), 6 deletions(-)
diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c b/drivers/usb/chipidea/ci_hdrc_imx.c
index 336ef6dd8e7d..873539f9a2c0 100644
--- a/drivers/usb/chipidea/ci_hdrc_imx.c
+++ b/drivers/usb/chipidea/ci_hdrc_imx.c
@@ -175,10 +175,12 @@ static struct imx_usbmisc_data *usbmisc_get_init_data(struct device *dev)
if (of_usb_get_phy_mode(np) == USBPHY_INTERFACE_MODE_ULPI)
data->ulpi = 1;
- of_property_read_u32(np, "samsung,picophy-pre-emp-curr-control",
- &data->emp_curr_control);
- of_property_read_u32(np, "samsung,picophy-dc-vol-level-adjust",
- &data->dc_vol_level_adjust);
+ if (of_property_read_u32(np, "samsung,picophy-pre-emp-curr-control",
+ &data->emp_curr_control))
+ data->emp_curr_control = -1;
+ if (of_property_read_u32(np, "samsung,picophy-dc-vol-level-adjust",
+ &data->dc_vol_level_adjust))
+ data->dc_vol_level_adjust = -1;
return data;
}
diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c
index 9ee9621e2ccc..1c7932f22218 100644
--- a/drivers/usb/chipidea/usbmisc_imx.c
+++ b/drivers/usb/chipidea/usbmisc_imx.c
@@ -659,13 +659,15 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
usbmisc->base + MX7D_USBNC_USB_CTRL2);
/* PHY tuning for signal quality */
reg = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG1);
- if (data->emp_curr_control && data->emp_curr_control <=
+ if (data->emp_curr_control >= 0 &&
+ data->emp_curr_control <=
(TXPREEMPAMPTUNE0_MASK >> TXPREEMPAMPTUNE0_BIT)) {
reg &= ~TXPREEMPAMPTUNE0_MASK;
reg |= (data->emp_curr_control << TXPREEMPAMPTUNE0_BIT);
}
- if (data->dc_vol_level_adjust && data->dc_vol_level_adjust <=
+ if (data->dc_vol_level_adjust >= 0 &&
+ data->dc_vol_level_adjust <=
(TXVREFTUNE0_MASK >> TXVREFTUNE0_BIT)) {
reg &= ~TXVREFTUNE0_MASK;
reg |= (data->dc_vol_level_adjust << TXVREFTUNE0_BIT);
--
2.34.1
