Re: [PATCH v8 0/9] Add multiport support for DWC3 controllers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, May 14, 2023 at 11:19:08AM +0530, Krishna Kurapati wrote:
> Currently the DWC3 driver supports only single port controller which
> requires at most two PHYs ie HS and SS PHYs. There are SoCs that has
> DWC3 controller with multiple ports that can operate in host mode.
> Some of the port supports both SS+HS and other port supports only HS
> mode.
> 
> This change primarily refactors the Phy logic in core driver to allow
> multiport support with Generic Phy's.
> 
> Chananges have been tested on  QCOM SoC SA8295P which has 4 ports (2
> are HS+SS capable and 2 are HS only capable).
> 

I'm able to detect my USB stick on all 4 ports on the sa8295p adp.

Tested-by: Bjorn Andersson <andersson@xxxxxxxxxx>

Thanks,
Bjorn

> Changes in v8:
> Reorganised code in patch-5
> Fixed nitpicks in code according to comments received on v7
> Fixed indentation in DT patches
> Added drive strength for pinctrl nodes in SA8295 DT
> 
> Changes in v7:
> Added power event irq's for Multiport controller.
> Udpated commit text for patch-9 (adding DT changes for enabling first
> port of multiport controller on sa8540-ride).
> Fixed check-patch warnings for driver code.
> Fixed DT binding errors for changes in snps,dwc3.yaml
> Reabsed code on top of usb-next
> 
> Changes in v6:
> Updated comments in code after.
> Updated variables names appropriately as per review comments.
> Updated commit text in patch-2 and added additional info as per review
> comments.
> The patch header in v5 doesn't have "PATHCH v5" notation present. Corrected
> it in this version.
> 
> Changes in v5:
> Added DT support for first port of Teritiary USB controller on SA8540-Ride
> Added support for reading port info from XHCI Extended Params registers.
> 
> Changes in RFC v4:
> Added DT support for SA8295p.
> 
> Changes in RFC v3:
> Incase any PHY init fails, then clear/exit the PHYs that
> are already initialized.
> 
> Changes in RFC v2:
> Changed dwc3_count_phys to return the number of PHY Phandles in the node.
> This will be used now in dwc3_extract_num_phys to increment num_usb2_phy 
> and num_usb3_phy.
> 
> Added new parameter "ss_idx" in dwc3_core_get_phy_ny_node and changed its
> structure such that the first half is for HS-PHY and second half is for
> SS-PHY.
> 
> In dwc3_core_get_phy, for multiport controller, only if SS-PHY phandle is
> present, pass proper SS_IDX else pass -1.
> 
> Link to v7: https://lore.kernel.org/all/20230501143445.3851-1-quic_kriskura@xxxxxxxxxxx/
> Link to v6: https://lore.kernel.org/all/20230405125759.4201-1-quic_kriskura@xxxxxxxxxxx/
> Link to v5: https://lore.kernel.org/all/20230310163420.7582-1-quic_kriskura@xxxxxxxxxxx/
> Link to RFC v4: https://lore.kernel.org/all/20230115114146.12628-1-quic_kriskura@xxxxxxxxxxx/
> Link to RFC v3: https://lore.kernel.org/all/1654709787-23686-1-git-send-email-quic_harshq@xxxxxxxxxxx/#r
> Link to RFC v2: https://lore.kernel.org/all/1653560029-6937-1-git-send-email-quic_harshq@xxxxxxxxxxx/#r
> 
> Test results:
> 
> Bus 3/4 represent multiport controller having 4 HS ports and 2 SS ports.
> 
> / # dmesg |grep hub
> [    0.029029] usbcore: registered new interface driver hub
> [    1.372812] hub 1-0:1.0: USB hub found
> [    1.389142] hub 1-0:1.0: 1 port detected
> [    1.414721] hub 2-0:1.0: USB hub found
> [    1.427669] hub 2-0:1.0: 1 port detected
> [    2.931465] hub 3-0:1.0: USB hub found
> [    2.935340] hub 3-0:1.0: 4 ports detected
> [    2.948721] hub 4-0:1.0: USB hub found
> [    2.952604] hub 4-0:1.0: 2 ports detected
> / #
> / # lsusb
> Bus 003 Device 001: ID 1d6b:0002
> Bus 001 Device 001: ID 1d6b:0002
> Bus 003 Device 005: ID 0b0e:0300
> Bus 003 Device 002: ID 046d:c077
> Bus 004 Device 001: ID 1d6b:0003
> Bus 002 Device 001: ID 1d6b:0003
> Bus 003 Device 004: ID 03f0:0024
> Bus 003 Device 003: ID 046d:c016
> 
> Krishna Kurapati (9):
>   dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport
>   dt-bindings: usb: Add bindings for multiport properties on DWC3
>     controller
>   usb: dwc3: core: Access XHCI address space temporarily to read port
>     info
>   usb: dwc3: core: Skip setting event buffers for host only controllers
>   usb: dwc3: core: Refactor PHY logic to support Multiport Controller
>   usb: dwc3: qcom: Add multiport controller support for qcom wrapper
>   arm64: dts: qcom: sc8280xp: Add multiport controller node for SC8280
>   arm64: dts: qcom: sa8295p: Enable tertiary controller and its 4 USB
>     ports
>   arm64: dts: qcom: sa8540-ride: Enable first port of tertiary usb
>     controller
> 
>  .../devicetree/bindings/usb/qcom,dwc3.yaml    |  22 +
>  .../devicetree/bindings/usb/snps,dwc3.yaml    |  13 +-
>  arch/arm64/boot/dts/qcom/sa8295p-adp.dts      |  52 +++
>  arch/arm64/boot/dts/qcom/sa8540p-ride.dts     |  22 +
>  arch/arm64/boot/dts/qcom/sc8280xp.dtsi        |  66 +++
>  drivers/usb/dwc3/core.c                       | 389 +++++++++++++++---
>  drivers/usb/dwc3/core.h                       |  28 +-
>  drivers/usb/dwc3/drd.c                        |  13 +-
>  drivers/usb/dwc3/dwc3-qcom.c                  |  28 +-
>  9 files changed, 543 insertions(+), 90 deletions(-)
> 
> -- 
> 2.40.0
> 



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux