Hi Matthias,
Thanks for your review comments,
On Thu, 5 Jan 2023 at 02:13, Matthias Kaehlcke <mka@xxxxxxxxxxxx> wrote:
>
> Hi Anand,
>
> On Wed, Dec 28, 2022 at 10:03:15AM +0000, Anand Moon wrote:
> > Genesys Logic GL3523-QFN76 is a 4-port USB 3.1 hub that has a reset pin to
> > toggle and a 5.0V core supply exported though an integrated LDO is
> > available for powering it.
> >
> > Add the support for this hub, for controlling the reset pin and the core
> > power supply.
> >
> > Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx>
> > ---
> > drivers/usb/misc/onboard_usb_hub.c | 1 +
> > drivers/usb/misc/onboard_usb_hub.h | 1 +
> > 2 files changed, 2 insertions(+)
> >
> > diff --git a/drivers/usb/misc/onboard_usb_hub.c b/drivers/usb/misc/onboard_usb_hub.c
> > index c0e8e6f4ec0a..699050eb3f17 100644
> > --- a/drivers/usb/misc/onboard_usb_hub.c
> > +++ b/drivers/usb/misc/onboard_usb_hub.c
> > @@ -410,6 +410,7 @@ static void onboard_hub_usbdev_disconnect(struct usb_device *udev)
> > static const struct usb_device_id onboard_hub_id_table[] = {
> > { USB_DEVICE(VENDOR_ID_GENESYS, 0x0608) }, /* Genesys Logic GL850G USB 2.0 */
> > { USB_DEVICE(VENDOR_ID_GENESYS, 0x0610) }, /* Genesys Logic GL852G-OHG USB 2.0 */
> > + { USB_DEVICE(VENDOR_ID_GENESYS, 0x0620) }, /* Genesys Logic GL3523-QFN76 USB 3.1 */
>
> Please drop the '-QFN76' suffix. The GL3523 comes in different packages, 'QFN76'
> is one of them, I'd expect the other packages to use the same product id.
>
> The GL3523 is a single IC, however like the TI USB8041 or the RTS5414 it
> provides both a USB 3.1 and a USB 2.0 hub. You should also add an entry for
> the USB 2.0 hub here.
>
Ok,
> > { USB_DEVICE(VENDOR_ID_MICROCHIP, 0x2514) }, /* USB2514B USB 2.0 */
> > { USB_DEVICE(VENDOR_ID_REALTEK, 0x0411) }, /* RTS5411 USB 3.1 */
> > { USB_DEVICE(VENDOR_ID_REALTEK, 0x5411) }, /* RTS5411 USB 2.1 */
> > diff --git a/drivers/usb/misc/onboard_usb_hub.h b/drivers/usb/misc/onboard_usb_hub.h
> > index 2ee1b0032d23..b32fad3a70f9 100644
> > --- a/drivers/usb/misc/onboard_usb_hub.h
> > +++ b/drivers/usb/misc/onboard_usb_hub.h
> > @@ -32,6 +32,7 @@ static const struct of_device_id onboard_hub_match[] = {
> > { .compatible = "usb451,8142", .data = &ti_tusb8041_data, },
> > { .compatible = "usb5e3,608", .data = &genesys_gl850g_data, },
> > { .compatible = "genesys,usb5e3,610", .data = &genesys_gl850g_data, },
> > + { .compatible = "genesys,usb5e3,620", .data = &genesys_gl850g_data, },
>
> s/genesys,//
>
> This reuses the settings of the GL850G hub, which doesn't seem correct in
> this case. For the GL850G a (minimum) reset time of 3us is configured. The
> data sheet of the GL3523 says:
>
> "The (internal) reset will be released after approximately 40 μS after
> power good.
>
> To fully control the reset process of GL3523, we suggest the reset time
> applied in the external reset circuit should longer than that of the
> internal reset circuit."
>
> Since it is 'approximately 40 μS' I'd say make the external reset 50 μS
> to be on the safe side, it's a very short time in any case.
>
Thanks for this input will update this in the next version.
> Please also add an entry for the USB 2.0 part of the IC.
alarm@odroid-n2:~$ lsusb -tv
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
ID 1d6b:0003 Linux Foundation 3.0 root hub
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M
ID 05e3:0620 Genesys Logic, Inc. GL3523 Hub
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/2p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
ID 05e3:0610 Genesys Logic, Inc. Hub
So earlier patch adds support for this device ID.
>
> > { .compatible = "usbbda,411", .data = &realtek_rts5411_data, },
> > { .compatible = "usbbda,5411", .data = &realtek_rts5411_data, },
> > { .compatible = "usbbda,414", .data = &realtek_rts5411_data, },
> > --
> > 2.38.1
> >
