Hi Anand,
On Wed, Dec 28, 2022 at 10:03:15AM +0000, Anand Moon wrote:
> Genesys Logic GL3523-QFN76 is a 4-port USB 3.1 hub that has a reset pin to
> toggle and a 5.0V core supply exported though an integrated LDO is
> available for powering it.
>
> Add the support for this hub, for controlling the reset pin and the core
> power supply.
>
> Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx>
> ---
> drivers/usb/misc/onboard_usb_hub.c | 1 +
> drivers/usb/misc/onboard_usb_hub.h | 1 +
> 2 files changed, 2 insertions(+)
>
> diff --git a/drivers/usb/misc/onboard_usb_hub.c b/drivers/usb/misc/onboard_usb_hub.c
> index c0e8e6f4ec0a..699050eb3f17 100644
> --- a/drivers/usb/misc/onboard_usb_hub.c
> +++ b/drivers/usb/misc/onboard_usb_hub.c
> @@ -410,6 +410,7 @@ static void onboard_hub_usbdev_disconnect(struct usb_device *udev)
> static const struct usb_device_id onboard_hub_id_table[] = {
> { USB_DEVICE(VENDOR_ID_GENESYS, 0x0608) }, /* Genesys Logic GL850G USB 2.0 */
> { USB_DEVICE(VENDOR_ID_GENESYS, 0x0610) }, /* Genesys Logic GL852G-OHG USB 2.0 */
> + { USB_DEVICE(VENDOR_ID_GENESYS, 0x0620) }, /* Genesys Logic GL3523-QFN76 USB 3.1 */
Please drop the '-QFN76' suffix. The GL3523 comes in different packages, 'QFN76'
is one of them, I'd expect the other packages to use the same product id.
The GL3523 is a single IC, however like the TI USB8041 or the RTS5414 it
provides both a USB 3.1 and a USB 2.0 hub. You should also add an entry for
the USB 2.0 hub here.
> { USB_DEVICE(VENDOR_ID_MICROCHIP, 0x2514) }, /* USB2514B USB 2.0 */
> { USB_DEVICE(VENDOR_ID_REALTEK, 0x0411) }, /* RTS5411 USB 3.1 */
> { USB_DEVICE(VENDOR_ID_REALTEK, 0x5411) }, /* RTS5411 USB 2.1 */
> diff --git a/drivers/usb/misc/onboard_usb_hub.h b/drivers/usb/misc/onboard_usb_hub.h
> index 2ee1b0032d23..b32fad3a70f9 100644
> --- a/drivers/usb/misc/onboard_usb_hub.h
> +++ b/drivers/usb/misc/onboard_usb_hub.h
> @@ -32,6 +32,7 @@ static const struct of_device_id onboard_hub_match[] = {
> { .compatible = "usb451,8142", .data = &ti_tusb8041_data, },
> { .compatible = "usb5e3,608", .data = &genesys_gl850g_data, },
> { .compatible = "genesys,usb5e3,610", .data = &genesys_gl850g_data, },
> + { .compatible = "genesys,usb5e3,620", .data = &genesys_gl850g_data, },
s/genesys,//
This reuses the settings of the GL850G hub, which doesn't seem correct in
this case. For the GL850G a (minimum) reset time of 3us is configured. The
data sheet of the GL3523 says:
"The (internal) reset will be released after approximately 40 μS after
power good.
To fully control the reset process of GL3523, we suggest the reset time
applied in the external reset circuit should longer than that of the
internal reset circuit."
Since it is 'approximately 40 μS' I'd say make the external reset 50 μS
to be on the safe side, it's a very short time in any case.
Please also add an entry for the USB 2.0 part of the IC.
> { .compatible = "usbbda,411", .data = &realtek_rts5411_data, },
> { .compatible = "usbbda,5411", .data = &realtek_rts5411_data, },
> { .compatible = "usbbda,414", .data = &realtek_rts5411_data, },
> --
> 2.38.1
>
