On Mittwoch 16 September 2009, Oliver Neukum wrote: > Am Mittwoch, 16. September 2009 13:56:26 schrieb Volker Armin Hemmann: > > ok, I am done. Was back earlier then expected and had an > > all-awake-night, so lots of time: > > Thank you very much for the great testing. > > > with > > USB selective suspend/resume and wakeup on > > > > Root Hub Transaction Translators on > > Improved Transaction Translator scheduling off > > > > mouse is fine > > > > > > with > > USB selective suspend/resume and wakeup on > > > > Root Hub Transaction Translators off > > Improved Transaction Translator scheduling on > > > > mouse is fine > > So this is an EHCI root hub problem most likely. > This means we need to include Alan, master of ehci. > > He'll need additional debugging info. Do you know how to get > at the ehci registers through debugfs? > Furthermore, if you have a hub can you try to attach your mouse > through a hub? > > Regards > Oliver > emm, the mouse is attached through a powered 4port usb 2.0 hub. That is the only way to get it working. If I attach it directly (without loading ohci) it does not work (well, only tried with both Transaction Translator options off), and if I load ohci before I connect it, it is very very jerky. So jerky in fact, that I considered douzends of lockups a day a better alternative. debugfs is mounted (and usbmon too.): cat /sys/kernel/debug/usb/ehci/0000:00:12.2/registers bus pci, device 0000:00:12.2 EHCI Host Controller EHCI 1.00, hcd state 1 ownership 00000001 SMI sts/enable 0xc0080000 structural params 0x00102306 capability params 0x0000a072 status 4008 Periodic FLR command 010019 (park)=0 ithresh=1 Periodic period=256 RUN intrenable 37 IAA FATAL PCD ERR INT uframe 232f port 1 status 001000 POWER sig=se0 port 2 status 001005 POWER sig=se0 PE CONNECT port 3 status 001000 POWER sig=se0 port 4 status 001000 POWER sig=se0 port 5 status 001000 POWER sig=se0 port 6 status 001000 POWER sig=se0 irq normal 20356 err 2 reclaim 16 (lost 0) complete 20359 unlink 0 cat /sys/kernel/debug/usb/ehci/0000:00:13.2/registers bus pci, device 0000:00:13.2 EHCI Host Controller EHCI 1.00, hcd state 1 ownership 00000001 SMI sts/enable 0xc0080000 structural params 0x00102306 capability params 0x0000a072 status 0008 FLR command 010009 (park)=0 ithresh=1 period=256 RUN intrenable 37 IAA FATAL PCD ERR INT uframe 3a34 port 1 status 001000 POWER sig=se0 port 2 status 001000 POWER sig=se0 port 3 status 001000 POWER sig=se0 port 4 status 001000 POWER sig=se0 port 5 status 001000 POWER sig=se0 port 6 status 001000 POWER sig=se0 irq normal 0 err 0 reclaim 0 (lost 0) complete 0 unlink 0 this is with 'all off', translators off selective resume off. Glück Auf, Volker -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
