Hi Martin,
On 7/11/2021 9:56 PM, Martin Blumenstingl wrote:
> Hi Minas,
>
> thanks for taking the time to get back to us!
>
> On Sun, Jul 11, 2021 at 10:15 AM Minas Harutyunyan
> <Minas.Harutyunyan@xxxxxxxxxxxx> wrote:
>>
>> Hi Martin,
>>
>> On 7/10/2021 9:07 PM, Martin Blumenstingl wrote:
>>> Hi Minas,
>>>
>>> On Thu, Jul 1, 2021 at 1:09 AM Martin Blumenstingl
>>> <martin.blumenstingl@xxxxxxxxxxxxxx> wrote:
>>>>
>>>> Hi Minas,
>>>>
>>> It's been a week since I sent my last mail
>>> In case you are taking some days off: enjoy that time!
>>> Please let us know if you have any questions about this as we're
>>> looking forward to some hints on how to debug (and of course fix!)
>>> this.
>>>
>> First of all sorry for late feedback. I missed this email thread because
>> in the subject there are no "dwc2" and my Outlook not move it to "dwc2"
>> folder of my mailbox based on rules. Today, because of rear count of
>> emails in linux-usb I was able to catch it.
>> I have added "dwc2" word in subject to avoid this situation later.
> Understood - I'll try to keep that in mind for the future.
>
>> Couple of questions to understand the case.
>>
>> 1. Is it work normally earlier? If it was works fine earlier then which
>> Kernel version and after which version broke?
> I am not sure in which kernel version it broke.
> Commit cc10ce0c51b13d ("usb: dwc2: disable power_down on Amlogic
> devices") submitted by myself made USB hotplug work (at least that's
> what the commit message says and that's what I remember).
> I haven't done any git bisect though yet
>
>> 2. Do you saw in dmesg:
>> dwc2_core_reset: HANG! Soft Reset timeout GRSTCTL_CSFTRST
>> If yes, then PHY not initialized correctly. Core can't reset if some
>> clocks from PHY are not available.
> I think you saw this in Anand's kernel log output.
> We came to the conclusion that some of his out-of-tree patches broke
> USB for him.
>
>> 3. During our recent testings we met the issue with PHY driver. Artur
>> found a bug in phy_generic driver and submitted patch on July 10:
>> [PATCH v2] usb: phy: Fix page fault from usb_phy_uevent
>> In your case, as I understand correctly, used
>> drivers/phy/amlogic/phy-meson8b-usb2.c. Could you please check if same
>> issue exist there.
> phy-meson8b-usb2.c uses the generic PHY framework (from drivers/phy)
> instead of the USB PHY framework (from drivers/usb/phy).
> The generic PHY framework does not have any event support.
> I am also not seeing any kernel BUG or WARN in dmesg. So my conclusion
> is that the phy-meson8b-usb2.c driver is not affected by the same
> issue.
>
>> 4. Can you provide full debug log for failed case?
> sure, in my kernel config I now have:
> CONFIG_USB_DWC2_DUAL_ROLE=y
> CONFIG_USB_DWC2_DEBUG=y
> # CONFIG_USB_DWC2_VERBOSE is not set
> # CONFIG_USB_DWC2_TRACK_MISSED_SOFS is not set
> CONFIG_USB_DWC2_DEBUG_PERIODIC=y
>
> With that, here's the output I get (including lsusb -t):
> 1. booting my Odroid-C1 with no external USB device plugged in (the
> USB hub you see in the lsusb output is soldered down on the PCB, so
> it's "always there")
> 2. plugging in a Corsair Voyager USB 3.0 flash drive (nothing
> automatically happened), then running lsusb -vv and lsusb -t
> 3. unplugging the Corsair Voyager and plugging in a USB 3.0 card
> reader (nothing automatically happened), then running lsusb -vv and
> lsusb -t
Could you please set verbose debugging:
CONFIG_USB_DWC2_VERBOSE=y
and repeat test 3. There are couple of transaction errors and some EP
stalled. I want to understand on which device/ep this happen.
Thank,
Minas
> 4. reboot, keeping the USB 3.0 card reader plugged in during boot
>
> lsusb -vv is needed to make newly plugged in devices show up after boot.
> This works fine with a few cheap USB 2.0 flash drives and an USB 3.0
> card reader that I have.
> However, with a Corsair Voyager USB 3.0 flash drive this doesn't work,
> I cannot see that on the bus at all.
>
> There's also a fifth case for which I have not attached any logs (but
> I can do so if required):
> If I have for example the USB 3.0 card reader or a cheap USB 2.0 flash
> drive plugged in during boot then USB hotplug is working.
> Even the Corsair Voyager USB 3.0 flash drive is detected.
>
> Please note that logfile 2 and 3 contain some "overlap" with the
> previous log in the dmesg output.
> For example: the first two lines in the "dmesg | tail -n13" output in
> logfile 2 are from the first logfile.
> I did this to show that I didn't omit anything by accident.
>
>> 5. I would preferred to see output of 'lsusb -t' for pass and fail cases.
> I included that output in all attached logs
>
> If you need any additional info, logs, etc. then please don't hesitate to ask!
>
>
> Best regards,
> Martin
>
